[ Log In ]
[ Register ]

Question #: 14597

Question: Where can I get a motor driver "TX14207", or a substitute with instructions?

Current Solution

I would recommend using our 5.6 amp driver as a replacement for the TX14207 driver. Apparently, those drivers are found in the 6040 CNC routers and will not contain documentation since it is typically sold as a part of a greater assembly. Here is the link to the recommended driver:
https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

Respond:

Other Possible Solutions to this Question

  • where can I find wiring instructions for the Mach3 USB controller?

    You can find all of the wiring instructions for the Mach3 USB controller here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Scroll down until you see the videos. The wiring instructions cover wiring all of the axes, setting up the inputs to sense limit switches, setting up the outputs and how to diagnose the outputs, setting up an external relay to control external devices, and setting up spindle speed.

    Click the link to add information to this solution:
    where can I find wiring instructions for the Mach3 USB controller?

  • Are the kits provided with printed instructions or a hi-res version of whats online?

    Some of our kits use video instructions to complete the assembly and those videos can be downloaded from youtube. The kits that offer illustrations and narrative associated with the illustrations are intended to be used directly from that product page. If you wish to receive printed instructions, please call us to specifically request this.

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    TctyH5A7

    Additional Information:
    -1 OR 2+544-544-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+181-181-1=0+0+0+1

    Additional Information:
    -1' OR 2+544-544-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+409-409-1=0+0+0+1 or 'YqFOAy5a'='

    Additional Information:
    -1" OR 2+380-380-1=0+0+0+1 --

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    xcfL6U8x'; waitfor delay '0:0:15' --

    Additional Information:
    rX9a3bfP'); waitfor delay '0:0:15' --

    Additional Information:
    evHzDfpD')); waitfor delay '0:0:15' --

    Additional Information:
    -5 OR 110=(SELECT 110 FROM PG_SLEEP(15))--

    Additional Information:
    -5) OR 585=(SELECT 585 FROM PG_SLEEP(15))--

    Additional Information:
    -1)) OR 963=(SELECT 963 FROM PG_SLEEP(15))--

    Additional Information:
    74ExMZFx' OR 396=(SELECT 396 FROM PG_SLEEP(15))--

    Additional Information:
    sADmKZTL') OR 910=(SELECT 910 FROM PG_SLEEP(15))--

    Additional Information:
    BwQqNiWP')) OR 809=(SELECT 809 FROM PG_SLEEP(15))--

    Additional Information:
    YQHwupOA')) OR 34=(SELECT 34 FROM PG_SLEEP(6))--

    Additional Information:
    vjQP3wiW')) OR 626=(SELECT 626 FROM PG_SLEEP(13))--

    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@qpunq

    Additional Information:
    @@qpunq

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    Are the kits provided with printed instructions or a hi-res version of whats online?

  • Can I drive my X axes with 2 motors using one motor driver?

    It is not recommended to drive two stepping (stepper) motors with a single driver. The driver will need to output the sum of the current that is rated for both motors. The best way to drive two motors on the same axis, or if you need the motors to spin in a synchronous fashion, then have each motor connected to their own driver and connect the signal wires from the drivers to the same signal step and direction pin on the breakout/interface board.

    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    Can I drive my X axes with 2 motors using one motor driver?

  • WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

    You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

    Additional Information:
    wire size

    Click the link to add information to this solution:
    WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

  • Is there a way to change the direction of a motor with the motor to driver wiring?

    You can change the direction of a stepper motor's rotation by swapping the A and B coils where the stepper motor is connected to the stepper driver. This may not work with every stepper motor and driver combination.

    To do this:
    - Turn off all power to the stepper drivers. If this is not done, you will damage the stepper driver.
    - Wait at least 1 minute for the power to dissipate from the drivers and power supply.
    - Once power is off, remove the wires from the A+ and A- and insert these wires into the B+ and B- respectively. Then insert the wires that were in the B+ and B- into the A+ and A- respectively.

    Click the link to add information to this solution:
    Is there a way to change the direction of a motor with the motor to driver wiring?

  • Using your NEMA 24 stepping motor with microstepping, can I get a speed range from 3 RPM to 600 RPM ?
  • I have a KL23H2100-30-4B motor with a KL-4030 driver and my motor stalls if I set the rapid above 180 imp.

    What mechanical drive system are you using? If your mechanical drive system connected to the stepper motor causes the motor to spin too fast, then you will be reaching the torque limit of the motor under the load of your axis.

    Click the link to add information to this solution:
    I have a KL23H2100-30-4B motor with a KL-4030 driver and my motor stalls if I set the rapid above 180 imp.

  • I've built a machine where the y axis has (2) 425oz motors, x axis has (1) 425oz. motor, and the z axis also has (1) 425oz motor. Would it be better to purchase a redleaf system with 4 drivers? or can I just connect both y axis motors to the same driver for a total of 3 drivers?

    In all CNC electronics configurations, you will need the motor paired with its own driver.

    If two motors/drivers are intended for a single axis and the motors need to turn at the same rate and in the same direction, then the two drivers for these motors should be connected to the same signal wires from the breakout board (step (CP) and direction (CW)) signal wires.

    If the motors need to turn in opposite directions, then either one driver will need to have the direction signal inverted, or resolve the opposite direction through a change in the mechanical drive train (i.e. flip the rack on a rack and pinion configuration, or in a roller chain setup, have the chain ride along the opposite side of the drive sprocket).

    How do I go about purchasing a redleaf system with 4 drivers, where the (y) and (a) driver are connected to the same signal from the breakout board? I'd also need them to rotate in opposite directions.

    The redLeaf webpage contains a purchase option for an extra motor and driver. We can setup the redLeaf system uniquely so it conforms to your application (i.e. motors running in opposite directions).

    Click the link to add information to this solution:
    I've built a machine where the y axis has (2) 425oz motors, x axis has (1) 425oz. motor, and the z axis also has (1) 425oz motor. Would it be better to purchase a redleaf system with 4 drivers? or can I just connect both y axis motors to the same driver for a total of 3 drivers?

  • [73] Are there instructions that come with CAMBAM

    The instructions for CAMBAM is located on the CAMBAM website here:

    Written documentation: http://www.cambam.info/doc/
    Video documentation: http://www.cambam.info/vids/
    FAQ: http://www.cambam.info/support/

    Videos on the BuildYourCNC YouTube channel:

    Project using a CNC Router - The Complete Process from Start to Finish - A Must-See for Beginners



    CNC Beginner Overview - One Demonstration of the CAD, CAM and CNC Milling Process


    CNC Routing Process (CAD, CAM and CNC Control) Variant 1: CAMBAM to Mach3 and CNC Routing


    CNC Routing Process (CAD, CAM and CNC Control) Variant 2: Part 1 Starting the Design in AutoCAD


    CNC Routing Process (CAD, CAM and CNC Control) Variant 2: Part 2 Finishing the Design in AutoCAD


    CNC Routing Process (CAD, CAM and CNCl) Variant 2: Part 3 Apply Machining Operations in CAMBAM


    CNC Routing Process (CAD, CAM and CNCl) Variant 2: Part 4 Cut Out the Shelves.


    CNC Routing Process (CAD, CAM and CNCl) Variant 2: Part 5 Cut Out the Legs and Assemble.


    Part 1: From SketchUp to Fabrication


    Part 2: From SketchUp to Fabrication

    Click the link to add information to this solution:
    [73] Are there instructions that come with CAMBAM

  • [575] Instructions read 24v on the card, can it support 36vdc ?

    The power supply that is used to power this controller must be 24VDC maximum. Any higher voltage and the controller components can be damaged. The 24VDC power supply doesn't need to be a high amp power supply. I would recommend This power supply: https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

    Click the link to add information to this solution:
    [575] Instructions read 24v on the card, can it support 36vdc ?

  • Can you sell me a kit to control my motor from the pc? I already have a motor, driver and power supply.

    All you need is a CNC controller like the following options:

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

    Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

    Click the link to add information to this solution:
    Can you sell me a kit to control my motor from the pc? I already have a motor, driver and power supply.

  • Transaction EQEPB4915043, My 2.2Kw Spindle and Inverter showed up without any manual or instructions. Can you provide a manual? Thank you

    The spindle does not come with a manual, however the inverter should come with a manual booklet in the box. The wiring diagram and PD settings for the inverter and spindle (https://www.buildyourcnc.com/item/spindle-inverter-2!2kw-spindle-novfd) can be view together on the spindle page, also you can use a local hardware store extension cord (orange) to connect/wire from your outlet(220V) to your inverter and spindle accordingly from the diagram.

    Additional Information:
    I also received a spindle and inverter without a manual. While the diagrams on the product page were sufficient to get the unit running, there is no documentation anywhere to be found concerning the terminal block that is used for external control. What does one have to do to get a hold of the manual that was supposed to come with the inverter? Manuals for the 220VAC model are plentiful online; however, manuals for the 110VAC model are non-existent.

    Click the link to add information to this solution:
    Transaction EQEPB4915043, My 2.2Kw Spindle and Inverter showed up without any manual or instructions. Can you provide a manual? Thank you

  • I need wiring instructions for the breakout board you sent yesterday. It is not like the one in the videos and I don't know where to connect the 5V. No data sheet or anything.
  • Yawl sold me a ST-USB MOTION CARD I have surched all your electronics and can't find wring instructions I need to know where to connect X,Y and Z to this controler

    To connect the stepper motor drivers to the Mach3 USB interface card, you will need to follow the wiring diagram here: https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf
    which can be found here: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board along with all of the other manuals associated with that interface card.

    Please note that the DC+ and DC- on that wiring diagram (power supply to thye stepper motor drivers) is not correct. The DC- is connected to GND on the drivers and the DC+ is connected to VCC on the drivers. Typically, the DC+ on the power supply is labeled V+ and the DC- is labeled either COM or V-.

    If you are having any issues with the wiring, please let me know and I will elaborate. Thanks.

    Click the link to add information to this solution:
    Yawl sold me a ST-USB MOTION CARD I have surched all your electronics and can't find wring instructions I need to know where to connect X,Y and Z to this controler

  • [575] How do I get the USB Driver to work with Mach3 Version 1.84

    What problems are you experiencing?

    Additional Information:
    Are you able to install a newer version of Mach3? If you are worried that your configuration will be lost, you can save the configuration by copying all of the XML files from the Mach folder. The XML files contain all of the settings that you applied in Mach3. Just in case the XML files are not compatible with the new version, make sure not to erase the current Mach3 that you have on the machine.

    Click the link to add information to this solution:
    [575] How do I get the USB Driver to work with Mach3 Version 1.84

  • DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

    The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

    Additional Information:

    Click the link to add information to this solution:
    DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

  • Do you offer or can recommend a place where I can buy the Drive Pulley for NEMA 43 Stepper Motor (1586 oz-in 3/4" single shaft) 5.5 Amps?

    We don't offer those drive pullies with a 3/4" bore at the moment. We can supply them if you are willing to wait. If so, what is the pulley pitch, how many teeth and the width of the belt.

    Additional Information:
    Meant to say pulleys, not pullies.

    Click the link to add information to this solution:
    Do you offer or can recommend a place where I can buy the Drive Pulley for NEMA 43 Stepper Motor (1586 oz-in 3/4" single shaft) 5.5 Amps?

  • I need the drive setting for the 1.5kw spindle drive to work with the spindle motor where do I find them

    If you purchased the spindle from us, you should have received a little booklet that shows all of the program settings. If you did not receive that booklet, please call us so we can send you this booklet.

    If you have the booklet, please let us know specifically what setting you would like to set and we can help.

    Click the link to add information to this solution:
    I need the drive setting for the 1.5kw spindle drive to work with the spindle motor where do I find them

  • Are there any instructions for use the USP breakout board for a CO2 laser?

    The instructions to connect the USB CNC Interface for the blackTooth Laser Cutter and engraver can be found on instruction #18 on thispage: https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx

    Click the link to add information to this solution:
    Are there any instructions for use the USP breakout board for a CO2 laser?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.