Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
What doesn't come with the electronics that I will need so it will work?

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
What do I need to purchase that doesn't come with the electronics packages?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
I bought a used cnc router. Can you make the electronics work?

If you do not have electronics for your CNC, you will need stepper motors (or servos) that will fit your torque requirements, drivers for the motors, a power supply, applicable wires, and an interface board for computer communication. We sell electronic combo kits here https://buildyourcnc.com/electronicscombo.aspx

Click the link to add information to this solution:
I just bought a 3040 800 watt cnc. What electronics do i need to buy to run it?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
I need my spindle and cnc electronics repaired. How can I fix it?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
Can you repair the electronics on my CNC machine?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
My cnc electronics does not turn on with my spindle. How can I fix it?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
Can you finish putting my CNC electronics together for me?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
How do I wire my cnc electronics?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
Can I send used CNC electronics to you for a retrofit?

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
what do I need to hook up the electronics?

The electronics and wiring videos are located under the tutorials section (click Tutorials on the top menu. The Title is "CNC Electronics and Wiring". The actual link to these videos is: https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

Additional Information:
You will also find the electronic wiring videos for the USB controller at: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
where can I find the videos to connect the cnc electronics?

Please explain what the number 500 is? Thanks

Click the link to add information to this solution:
ReplicatorG says my white ant extruder is at 500 or more. I've replaced the electronics on the printer but that hasn't fixed it what else can I do?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

The available options for the blackFoot, is only structural components with hardware, and structure components/hardware with electronic components.
However we currently do not have any plans available for public use/distribution.

Click the link to add information to this solution:
I have a 4x8 CNC and would like to cut my own parts for the Blackfoot. What is the price for the plans and the electronics ?

There are three options on the blackFoot product page.

Two options include either electronics that use the USB interface, or parallel interface. Both of these options include stepping motors (two 425 oz-in and one 651 oz-in), motor drivers (two 3.0 amp and one 6.0 amp), power supply and either a parallel breakout board, or USB breakout board. The USB interface must be used with the planet-cnc software. The parallel interface can be used in a wider variety of control software but will require a parallel port on your computer. If a parallel port doesn't exist, you can purchase a PCI parallel port adapter (for desktop computers only).

The other option does not include electronics. This option is if you already have electronics, motors and drivers that will work with this machine, or you wish to purchase the redLeaf or redSprout assembled and plug and play CNC electronics and computer system.

Click the link to add information to this solution:
What electronics configuration is included with the blackfoot if I choose that option?

Yes, we have a 4 axis combo kit available under Motion Electronics.

Click the link to add information to this solution:
Can you supply an electronics package for a dual x-axis CNC machine (X, Y, Z)

The plans/hardware/electronics/mechanical includes everything but the wood structural components that can be cut by the customer. This plans/hardware option includes all of the electronics, like motors, drivers, controller, and all of the cables and wires to connect all of the electronics together. The mechanical components include shafts, couplings, linear rails, bearing blocks, sprockets, lead screws, etc. The hardware consists of all of the screws nuts, insert nuts, cross dowels, etc, to assemble all of the structural, mechanical, and electronics together.

Click the link to add information to this solution:
what does the plans, hardware, electronics and mechanical option consists of for a CNC router?

The electronics (stepper motors, drivers, power supply and interface board) can be found here:
https://www.buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

If your computer cannot connect to the parallel breakout board (the interface card), just make sure to inform us that you need the USB alternative.

Click the link to add information to this solution:
Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?