The dual 24VDC relay can use any 24V power supply that outputs 24V DC. A great power supply that will work well with this dual 24VDC relay is this power supply: https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
[797] Should I use a 24V power supply for this relay?

We generally use the USB to power the interface (breakout board). The current from the computer is sufficient to supply the breakout board.

Click the link to add information to this solution:
I have a blue brew break-out board. Do I use a seprate power supply for it and what amp output should it have if used.

We generally use the USB to power the interface (breakout board). The current from the computer is sufficient to supply the breakout board.

Click the link to add information to this solution:
I have a blue brew break-out board. Do I use a seprate power supply for it and what amp output should it have if used.

The 2.2kW spindle has a power rating of 2.2kW or 2200 watts.

If the VFD AC voltage input is rated for 220 volts, then 2200 watts / 220 volts is 10 amps, so a 15 or 20 amp breaker will work.

If the VFD AC voltage input is rated for 110 volts, then 2200 watts / 110 volts is 20 amps, so a 25 or 30 amp breaker will work.

Additional Information:



Additional Information:

Click the link to add information to this solution:
[77] What circuit breaker should I use for this spindle?

The 2.2kW spindle has a power rating of 2.2kW or 2200 watts.

If the VFD AC voltage input is rated for 220 volts, then 2200 watts / 220 volts is 10 amps, so a 15 or 20 amp breaker will work.

If the VFD AC voltage input is rated for 110 volts, then 2200 watts / 110 volts is 20 amps, so a 25 or 30 amp breaker will work.

Additional Information:



Additional Information:

Click the link to add information to this solution:
[79] What size circuit breaker should I use for this VFD?

The 2.2kW spindle has a power rating of 2.2kW or 2200 watts.

If the VFD AC voltage input is rated for 220 volts, then 2200 watts / 220 volts is 10 amps, so a 15 or 20 amp breaker will work.

If the VFD AC voltage input is rated for 110 volts, then 2200 watts / 110 volts is 20 amps, so a 25 or 30 amp breaker will work.

Additional Information:



Additional Information:

Click the link to add information to this solution:
[78] What size circuit breaker should I use for this spindle?

I would recommend either a 36VDC or a 48VDC power supply with 10 amps. Here are links to these power supplied on this website:

https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-36v-48v

Click the link to add information to this solution:
[807] What size power supply do I need to this?

Most of our power supplies allow for a 9 amp current draw.

For the Neutral, Live and earth ground, wire gauge for that level of current is 14 for relatively short cable lengths. Increase the gauge for longer lengths past 25 feet.

For the DC 24V output terminals to the drivers, 20 gauge is fine. If the power supply is connecting to only one driver, increase the wire gauge to 14.

Additional Information:
What gage wire should I use from motor to driver

Additional Information:


Additional Information:

Click the link to add information to this solution:
What wire AWG can I use to connect the power supply 24v 8.3 amps

When connecting our power supply, no matter if it is 24 or 36 volts with our drivers/motors, you should always use bipolar parallel. This will allow you to have the best torque at higher speeds.

Click the link to add information to this solution:
I have your nema 24 motors using the 36v power supply. Should I use the Bipolar series for the wiring the motors since I am using the 36 volt ad not a 24v power supply?

Yes, you can use 2 motors in the same axis output, however you will still need a driver for that motor! Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

Also you can run a slave motor using another axis on the board, and setting it up in the Planet-CNC settings.

Planet-CNC/File/Settings/Axes, here you will enter 3 in the Number of Axes location, and then change the Function of the Axis 4 to Slave 1. There you will have the 4th axis or A-axis be a slave for the x-axis.
Slave 1 - X-Axis
Slave 2 - Y-Axis
Slave 3 - A-Axis
Slave 4 - B-Axis
Etc...




Additional Information:
Do you act as if it's one motor and it goes to one controller on the motherboard?

Click the link to add information to this solution:
What wiring should I use to connect two motors for one axis?

The best choice would be a type K thermocouple.

Click the link to add information to this solution:
What thermocouple or thermister should I use for the extruder hot end?

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

Any of the following power supplies will be fine for powering the Mach3 USB controller:
https://www.buildyourcnc.com/item/24v

however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

The blackfoot requires a total of 50 feet of cable.

The X axis needs 15 feet
The Y axis needs 17 feet
and the Z-axis needs 18 feet

These are 20 gauge 4 conductor cable.

Additional Information:

Click the link to add information to this solution:
WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

The pocketing depth per pass will depend on the hardness of the material, the router/spindle you are using and on the melting point of the material. Use the feedrate that you would normally use for the size and type of end mill. You will need to test the depth per pass, starting at the full depth of the pocket. The spindle should have no problem, but if you are using a router, then it may bog down, so easing up on the depth per pass is recommended. If the spindle/router has no problem at the depths you are using, then you need to evaluate the edge finish to determine if it is acceptable. If it is not acceptable, then ease up on the depth per pass. Keep doing these steps until you have the finish and precision you expect.

Click the link to add information to this solution:
what depth increment should I use for pocketing and profiling with the 1/2" end mill?

Adding more fans will require more power from the power supply. Each fan should have the amps that the fan draws. Add the total amps from the three fans and add one amp for the pump and you will have the total power requirement. The 12V 2amp power supply that accompanies the spindle cooling kit will probably be insufficient for the additional two fans.

Click the link to add information to this solution:
[772] Can I add 3 fans and a bigger radiator to this with the 12vdc power supply

The motors could be wired incorrectly causing them to lock up. Make sure to check the wiring to make sure the X and Y are connected to the correct terminals.

Click the link to add information to this solution:
When Blacktooth is powered on the motors get power but will not turn. What should I do?

There are several specifications related to CAM software that you will need to consider.

1. The CAM software will need to be able to offer the features that match that of the machine you select to perform the fabrication. Some of these machines include, standard 3 axis vertical CNC milling machine, turning machine, and 4 or 5 axis CNC machine.

2. The CAM software will need to contain the features that you feel are necessary for how you will apply the machine. For example, are you making signs? Are you milling parts for a machine? There is a wide array of CAM software that will work well for one application and not another.

3. The CAM software will need to work well with your workflow and processes, and have the user interface that you prefer.

Click the link to add information to this solution:
How do I determine what CAM program I should use?

Yes, the purpose of the dual relay is so you have the ability to control two separate relays with two separate signals. One signal will go to one of the two relays, and the other signal will go to the other relay.

Click the link to add information to this solution:
[797] Can this relay accept two separate signals?