You will need to construct the table frame to your specifications and with a structure, fixtures and clamping to hold the timber that will be sculpted. You will also need the appropriate end mill that is designed to carve the timber. A dust extraction (vacuum) will be necessary to remove the dust and chips.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi, I intend on sculpting a surfboard out of a timber slab using the following kitset: greenBull 6x with Hybrid Laser/Spindle Head (includes Spindle/VFD and Laser Components) - USB Interface (Long Z). Will i need to purchase any additional items to have a fully operational cnc machine that is capable of carving the surfboard from a timber slab?

The Mach3 USB interface board will require a 24V power supply to enable the use of the input, output terminals, and the spindle VFD 0-10V and output for speed control.

Click the link to add information to this solution:
Hi Patrick right now I have a parallel port cnc machine that I built in 2013 using the hardware and components I purchased from your website. I want to update my system by changing my current parallel port interface board to a Mach3 USB interface board from your website. Is the Mach3 USB interface board all I need to do this or is there other components I need to get. please advise.

I can send you a new license. All you need to do is email me at customerservice@buildyourcnc.com and state the name the license is under and I will send you another license.

Click the link to add information to this solution:
I bought and downloaded about 2 years ago, recently my PC that I use for my CNC crashed and now have to reinstall Mach3 but the license download has since expired. What I need to do to activate the software?

Most likely, the driver is not receiving the high or low signal for the direction terminals. The way direction works for an axis is the controller will output a high signal (5V) for one direction and low signal (0V) for the opposite direction. If the signal is always at one signal, say 5V, whether it is commanded in one direction or the other, then the axis will only move in that direction.

To solve this problem, make sure that the wiring is secure at both ends (from the controller to the driver). Also, make sure the Dir+ and DIR- are both wired correctly (i.e. the Dir- is connected to the signal gnd on the controller and the ZD is connected to Dir+ on the driver.

You can use a multimeter to determine the voltage at the ZD terminal by:
- setting the multimeter to DC voltage (the V with a straight line, or dashed line above the V)
- place the black lead on the gnd terminal
- place the red lead on the ZD terminal
- press the page up button and check the voltage
- press the page down button and check the voltage.

You should see the voltage change from 0V to 5V or vice versa.

Click the link to add information to this solution:
Hi I have just set up my machine using a mach 3 USB board I can only get the Z to go in one direction Y and X are Ok I have check wiring and looked at video over and over what have I missed??

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

No, we have gotten away from the planet-cnc boards as they have decided to not support our board with their software. You can use the Mach3 USB board as an alternative. You will be better off with Mach3 as a control software as this is widely used and supported.

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have the older discontinued USB breakout board. The y-axis no longer works and have traced it to the breakout board. Is there a replacement board that can use the same Planet CNC software running on Windows 10?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

Consider the loads on each axis when choosing appropriate stepper motors. If your holding torque is maxed out at roughly 16oz/in (1lb/in), then you could use the NEMA 11 or 14. Also consider the shaft sizes and current ratings when choosing drivers that pair with the motors.

Click the link to add information to this solution:
I am planning to build a scratch CNC machine to do rotary engraving on writing pens. Can you recommend the parts I would need? I'm thinking NEMA 14 (11?) and 3/8" acme rod. Not sure which linear motion to use. I have an old lathe to use for the 4th axis.

Hi, you can call me at the 281-815-7701 number. Please leave a message when you call as most of the calls are screened to avoid scam calls. You can also email me at customerservice@buildyourcnc.com or phooddaniel@berkeley.edu.

The newer kits that are featured on the home page include everything you need except a computer and software. The legacy CNC routers that are located in the CNC machines menu selection include all of the parts for the gantry, but you will need to build the table yourself. All of the information on the measurements to be followed for the table construction are on the machine pages.

Click the link to add information to this solution:
I am looking at getting a 4x8 cnc router kit. I am having a hard time figuring out what is included in the kit and what else i will need to buy with it to get off the ground and running. Is there someone i could talk to to walk me through it? If not, can you break down what all I need to go from scratch to a running set up? thanks

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

Not sure what you mean by the statement "I don't know when you answer". Please explain. I answer all of the incoming emails until my inbox is completely empty and all phone calls to the company go straight to my cell phone and I answer all of the calls, and if I don't answer, I call back immediately.


Additional Information:
I just searched my email and found no emails with your email address associated with the email listed with this question. I cannot answer questions if no correspondence was provided by you.

Click the link to add information to this solution:
Please send an email, I am giving up on buying a machine from you because I don't know when you answer. I was asking about getting just the working parts and rails sent to Fiji. You sent an answer and some questions, but I have no way of knowing if you responded again.

Fusion 360 is a program that allows you to design in a parametric 3 dimensional environment and also provides a great CAM toolset. Fusion 360 will produce the gcode with the CAM capabilities. The gcode is used to move the machine in various ways in order to mill the material; however, software is needed to interpret this gcode and cause the machine to move according to the gcode instructions. This is called control software. So Fusion is CAD/CAM, and you still need "control". Mach3 is one example of control software for milling and is highly recommended.

Install Mach3 onto the computer that will connect to the redFly(CNC electronics), then configure the Mach3 parameters for the machine (motor tuning, plug-ins, inputs/output, etc.). Home the machine, load the gcode into Mach3 and the machine will move according to the gcode.

A word of caution, since you are new to CNC machines, make sure you familiar yourself with the machine and the movements of the machine specific to how the gcode is arranged with respect to the coordinates of the machine. Try with very simple gcode until you get a very good understanding of how the machine will move.

Click the link to add information to this solution:
Hello, My friend has purchased the Redfly and I am helping him a little with it. We are both very new to CNC. I am using fusion 360 at the moment. This can tool path and create gcode. I was wondering if Mach 3 or similar is still needed. Is there a tutorial you could point me to that explains how to get the Gcode from the PC, via Serial to the Redfly?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?

Yes, the Mach3 USB controller will work with the latest Windows version and in 64-bit mode. The 32-bit mode is only relevant for using the parallel port driver if you are using a parallel port breakout board. Since this controller is connected via a USB cable, the 64-bit state will work fine.

Additional Information:
mach3 not showing in device manager

Click the link to add information to this solution:
[575] I have a 64 bit Windows 11 laptop. Will this interface board work with this? If not is there an option you can suggest.

Decreasing the speed of acceleration in the cutter? Meaning of your router/spindle?, To modify the speed of a router will be going to the router itself and modifying the speed, but if a spindle is being used modifying it will be done either manually in the VFD (VFD Setup:
Change PD001 to '0' (source of run commands)
Change PD003 to 300 (main frequency - Hz)
Change PD004 to 300 (base frequency - Hz)
Change PD005 to 400 (max operating frequency - Hz)
Change PD006 to 2.5 (intermediate frequency - Hz)
Change PD008 to 220 (max voltage - V)
Change PD009 to 15 (intermediate voltage - V)
Change PD010 to 8 (minimum voltage - V)
Change PD011 to 100 (frequency lower limit - Hz)
Change PD142 to 7 (rated motor current - Amps)
Change PD143 to 2 (motor pole number)
Change PD144 to 3000 (rated motor revolution))<- make sure these are your settings in the VFD. If the spindle is wired to the breakout board and is working through Mach 3 then the modification will be done in your CamBam/Feed rate settings.

Click the link to add information to this solution:
How can I decrease the rapid acceleration of the cutter from a completed cutting operation to a new location so that the stepper motor will not lose its steps and mess up the machine zero settings? I am using CamBam and Mach3 on my machine with a chain drive. what is the best way to reduce accleration

Considering enlarging the machine, might have its down sides do to the structural integrity of the scratch build machine. Primarily by making the width longer it will start to sag in the center, which will lead to having to redesign the gantry to be more structurally rigid to support the added length. Which then will increase the weight and height of your gantry to support the add size, which will always end up to creating a larger CNC.

We usually do not recommend modifying the scratch build CNC, due to the very limited capabilities, and the structural design of the scratch build. We also do not recommend using longer than 48" ACME screw/leadscrew due to the increasing chance of warping and bending in the ACME screws/leadscrew in the given length.
We do recommend modifying the CNC machines we sell to accommodate the added requests that some of our customers desire, but you will be limited to the width of the gantry with our machines.

Click the link to add information to this solution:
I've read your book and I'm looking to purchase the hardware kit with DVD as well as an electronics kit. I would like my machine to have a working area of at least 24" wide by 48" long. Can I just make the bed (and gantry) wider to accommodate larger priceslike 30"x60"? If so what electronics kit would you recommend?

Yes, you can use a corner plate very easily. You will want to make a corner plate that has three independent plates that do not conduct with each other. Each of these plates will be connected to a different input (i.e. IN1 for X, IN2 for Y and IN3 for Z). The end mill or tool that is inserted into the spindle will connect to V- of the 24V power supply, or the DCM on the controller, which is connected to the 24V V-. Then, you can use the ref all home button on the program run screen of Mach3.

Click the link to add information to this solution:
I have the mach 3 USB board running a XYZ router, and a Z touch off (button style @ fixed position). I am wondering if there's a way to also use an X,Y plate that will only be responsible for corner finding. Is the digitize input the only input that can be used for a touch plate?

Make sure that the port setting for that output is set to port 3. To do this in Mach3, click config -> Ports & Pins -> click the outputs tab and in the list of outputs, select the output you want to use and set the port to 3.

Click the link to add information to this solution:
I have a single axis motion for my table saw fence. Motor, limit switches and e-stop work fine. I now need to add an air solenoid relay but I cannot get the outputs to work. I have 24v supply connected and tried using the Spindle output on pin 1. But using a multimeter, there is no voltage on the Output 1 terminal.