Try the probe connected between the input and DCM with just wires connected to those terminals. When you short the two wires, you should see the change in the diagnostic screen.

Make sure that the probe configuration is correct:
Config -> ports and pins -> inputs tab
on the probe line, make sure the pin number matches the IN number on the controller. Make sure that the port number is 3. And finally, make sure the active low is set correctly. Toggle the active low to toggle the normally open and normally closed state of the probe.

Additional Information:
Nothing changes in the diagnostic screen, however the Digitize led is lit. One wire on in4 the other on DCM. If I were to put a multi-meter to any of the pins would there show any voltage?

Click the link to add information to this solution:
[575] I have my probe conected and have checked continuity but my probe does not show to be working. What else could be wrong?

If you are getting the message RNR Motion Card Not Found, the controller is shorting. Check the wiring to make sure you have all of the correct wires in the correct terminals. Check the voltages of all the terminals to make sure everything shows the correct polarity and voltages.

Additional Information:
Mine did the same thing. Try pushing the USB cable all the way into the port and slightly up. My usb port on the card is slightly oversized and breaking the connection. Ordering some USB type B connectors off of amazon, gonna try and re-solder a new port on the card before replacing the card.

Additional Information:


Additional Information:
I am having the same problem but nothing has fixed it. I have replaced the card but still no results.


Additional Information:
I am having the same problem but nothing has fixed it. I have replaced the card but still no results.

Click the link to add information to this solution:
[575] After reset of E stop, I get error message "RnR Motion Card Not Found". Have you any advice?

Check that the port number in the outputs tab for the specific output you are using is set to port 3. Also, make sure you are wiring the output as shown in the outputs video below:

Click the link to add information to this solution:
[575] Hey friend have problem outups is always high m3 m5 not work

When the z axis is going down, the laser turns on. When the z axis is going up, it turns off. The z axis directions is only a signal that is either 5v or 0v. That determines the direction. In vectric, you will need to set your machining operations with a very very small depth so the time it takes to get to its final depth is a very short time.

Click the link to add information to this solution:
AM NOT SURE HOW TO SET THE Z AXIS TURN ON/OFF LASER WHEN CREATE CODE. KNOW THAT ITS TYPICALLY Z-AXIS MOVEMENT DOES THIS - BUT YOU DONT SHOW ANYTHING HOOKED UP IN PLACE OF AXIS.

Yes, the Mach3 USB controller will work with the latest Windows version and in 64-bit mode. The 32-bit mode is only relevant for using the parallel port driver if you are using a parallel port breakout board. Since this controller is connected via a USB cable, the 64-bit state will work fine.

Additional Information:
mach3 not showing in device manager

Click the link to add information to this solution:
[575] I have a 64 bit Windows 11 laptop. Will this interface board work with this? If not is there an option you can suggest.

Make sure that the spindle motor output pin is not interfering with the signal. Go to config -> ports and pins -> motor outputs, at the bottom of the table, there will be a line for spindle. Make sure that spindle line item is disabled.

Additional Information:
I disabled the spindle port and I am still only able to activate port 3 and get 24v and even there when I enter m5 the voltage bounces all over the place. The other outputs read all over the place whether they have been designated as the spindle on the spindle settings tab

Additional Information:
I tried wiring a relay to each of the outputs and only out3 was able to activate the relay

Click the link to add information to this solution:
[575] I connected this to 24v power supply and only out3 will show 24v when activated the other 3 read 300+v whether activated or not

with parallel port controllers, you have the ability to jog using two axes at the same time, but with USB controllers, this is not possible.

Click the link to add information to this solution:
[575] Hi, I recently purchased this board and everything seems to be fine! But I am not being able to jog two axis at same time as I used to do on my older board. Did I do something wrong?

You will need to change the default attribute of the browser that you are using (i.e. Google Chrome, IE, Firefox).

Instructions to change this default attribute:
1. Click on the "start menu"
2. Click on "control panel"
3. Click on "programs"
4. Click on "default programs"
5. Click on "set you default programs"
6. Select the browser that you would like to fix
7. Click on "choose defaults for this program"
8. Find where it says "mailto" and set that to the default that you desire.

Click the link to add information to this solution:
THE SEND MAIL IN CONTACT US PAGE OF BUILDYOURCNC.COM WEBSITE DOES NOT WORK. ALSO CALLED MAILTO:

Have you tried comparing all of the parameters for the motor outputs? For instance, go into the motor outputs screen in the mill profile, take note of all the parameters. Then open the turn profile, go into the motor outputs and change the parameters from the notes you had in the mill profile.

If that works, do the same for the other setting screens.

Click the link to add information to this solution:
[575] Everything works in mill, but if I wanna use turn software then there is problems to recognize rnrmotion card.

The Mach3 USB will not work with Mach4. Consider the Pokeys57CNC controller instead. The Pokeys57CNC controller will work with Mach3 or Mach4 and contains more features than most CNC machines need, including 8 motor outputs, 4 onboard relays, limit home and probe inputs, galvanically isolated outputs, and much more.
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[575] Will this work with Mach4. I,m thinking to upgrade from Mach3.

Open the input signals dialog box by clicking on config, then ports and pins, then input signals. For each line item that you use (i.e. x++, y--, etc) make sure the port number is 3.

Also, make sure there is a 24v power supply connected to the DCM and 24V terminals. One side of the NO on the limit switch must connect to the DCM, or the power supply V- terminal.

Additional Information:

Click the link to add information to this solution:
[575] I cannot get the limits to work I’m normally open as you state

You need to set up the homing/limits parameters. You can find this screen by clicking config->Homing/Limits. Make sure to wire the home switches on separate input terminals (i.e. X home switch on IN1, Y home switch on IN2, etc). You can add the limit switches to any of the IN terminals, even on the same IN terminals where the home switches are located.

Check out this video on how to wire multiple switches on a single terminal.

Additional Information:
20

Additional Information:
20

Click the link to add information to this solution:
[575] my axises X,Y,Z will all light green along with my soft limit switch button. When hitting REF ALL HOME no axis move and all my DROs go back to ZERO

What problems are you experiencing?

Additional Information:
Are you able to install a newer version of Mach3? If you are worried that your configuration will be lost, you can save the configuration by copying all of the XML files from the Mach folder. The XML files contain all of the settings that you applied in Mach3. Just in case the XML files are not compatible with the new version, make sure not to erase the current Mach3 that you have on the machine.

Click the link to add information to this solution:
[575] How do I get the USB Driver to work with Mach3 Version 1.84

To use a touch plate on any controller, all you need is a conductive flat material with a known thickness and some wire and alligator clips. Solder a wire to the touch plate and connect the other end of the wire to the free input terminal of the controller. Connect a wire with an alligator clip to the ground of the controller (on the Mach3 USB controller, this ground is the DCM terminal, or the digital gnd on the 24VDC power supply). Connect the alligator clip to the end mill.

You can either use a script to serve as the probe, or you can use the ref all home button and setup the touch plate as a home switch.

Additional Information:
I connect wire to cmd- and to in2. I cant getbit to work, what arecthe corresponding ports and pins to usenin mach3? Please help.

Click the link to add information to this solution:
[575] Can you tell me where to find a script (for Auto Tool Zero button) to zero Z axis from a touch plate?

You can use two MGPs (bare MPGs) to provide independent axis control. The handwheel input on this controller contains discrete inputs for the X, Y, Z, and A axes. These inputs can receive a pulse to move their axis. For instance, you can connect an MPG to the X-axis pin and the wheel will move the X-axis only.

Of course, if you have a traditional pendant, you can move any axis independently from only a single wheel with a switch that selects the axis you wish to move.

Click the link to add information to this solution:
[575] can we use two MPG for two axis independant axis movement

Are you using Mach3 or Mach4?

Additional Information:
using Mach3

Click the link to add information to this solution:
[816] PLS HELP ON TEST MODE THE LED DO COME ON BUT THERE IS NO MOVEMENT ON THE Z AXIS

If the pins from the terminal block on the side of the board are outputs, or at least 2 of them are outputs, then you can connect our modular driver to the board (example: cw230). If they are all inputs, then you would not be able to connect an external driver.

Click the link to add information to this solution:
I AM USING A XYLOTEX 3 AXIS BOARD AND WANT TO ADD ANOTHER MOTOR SLAVED THE X-AXIS. WILL DRIVE CW230 WORK?

Honestly, I have never looked at my device manager to determine what type of connection the MAch3 USB controller shows up as. I simply allow Mach3 to recognize the board via its plugin. Are you trying to use the controller in a non-conventional way?

Additional Information:
s

Click the link to add information to this solution:
[575] The controller shows up in device manager as a HID. Should it be a com-port?

OK, the Issue was with the wiring: Blue and Yellow, which is A+ A-, and Red and Green, which is B+ B-.

Working awesome now!

Click the link to add information to this solution:
[575] Mach3 board only jearking the steppers not rotating, i tried many settings but no luck here is the video https://1drv.ms/v/s!AuEcOHVa1BRjg7Iqu9teAEjsd4fnTA