Here are links to the sole pump and heat exchanger/fan. I am sending you amazon links sine I don't ahve listings of my pump and heat exchanger separately from my cooling system:
Pump: https://amzn.to/3R6zPbj
Fan/radiator (Heat exchanger): https://amzn.to/3UWOuqN

Click the link to add information to this solution:
I recently purchased a repalcement 12v DC Switching Power Supply, I hooked it up bur it did not power up the Pump and radiator. I verified the output of the unit at 12v. So I'm assuming I also need to replace the pump and the radiator. Can you supply me a link to purchase them?

Yes, if the power supplies were supplied by us, we will exchange them with 110v equivalent power supplies.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hello, I am a student working on a CO2 laser. We recently ordered two 40watt CO2 laser tubes and two 40 Watt CO2 Laser Tube Power Supply at 220V. However, our school is unable to use them due to being 220v. Is it possible to exchange these for the 110v supply, or is there a way we can go about connecting it at 110v instead of 220v? Thank you.

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
I'm trying to hook up the Spindle Cooling Kit with 12VDC Power Supply. I have all the tubes plumbed but can't figure out how to hook up the wires. The power supply you sent only has 2 AC input and 2 DC output screws. The fan has 2 wires and the pump has three and both have a JST connector. How do I wire them in?

If you were logged in when you made the purchase, you can click the "My Account" link at the top of any page on this website and see all of your orders, order line items (with direct links to these items), and shipment information.

Here is a link to the "My Account" page for your convenience:
https://www.buildyourcnc.com/CustomerInfo.aspx

I did not see your username on your internal customer record, so I added this username and you should be able to see the information in the "My Account" page.

Additional Information:
I just tested your accounts page and the cable carrier links are in there. Thanks and please let me know if you need further assistance.

Click the link to add information to this solution:
I have purchased cable carrier chain and would like to know if you could send me a copy of that order as I need to purchase extra lengths of the links I bought. Thanks

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
What else to I need to purchase along with the "3 Axis Electronics Combo w/ USB Interface Board" to get the electronics up and running? (software, 5V power supply, 4-conductor wire, etc.)

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
I've built a router frame, so I need electronics. I'm buying 2 NEMA 34s and 1 NEMA 23. Can I get a list of controller, power supply and related components so I can get them as I can afford them? Please.

Absolutely, I can answer this type of question and anything other questions you may have with your new-to-you CNC router.

Additional Information:
20

Click the link to add information to this solution:
[789] Can you help me with selecting a power supply ( and a few other components ) for the stepper motors that came with a homemade CNC Router I just purchased.

There is some variation in the outward appearance of laser power supplies due to sourcing through different vendors. However, the basic wiring requirements are the same in each case. For the unit with integrated laser controller, follow the diagram found here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/. The terminals on the signal side will have a 6 connection terminal block -- these are the ones labeled 5V, IN, G, P (or WP), L (or TTL-L), and H (or TTL-H). The High Power side will have 3 inputs for AC power, one high voltage lead, and one return line. Connect these as shown in the diagram as well: the return line goes on the "front" (beam exit end) terminal of the laser tube, the high voltage lead goes to the "back" terminal of the tube, the FG terminal (or G) receives the earth ground wire of the AC power cable, and the two AC terminals receive the line and neutral wires of the AC power cable (it doesn't matter in this case which wire goes to which terminal).

Click the link to add information to this solution:
I purchased the blackTooth Laser Engraver with integrated Laser Control Unit and have been following your instructions. I noticed that the laser tube power supply is different that what is shown in your instructions. Do you have any better wiring guides that I can follow for the version that I received?

Yes, here is the URL for the parallel breakout board that we sell:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
can I purchase just the parallel controller board? I purchased the usb option 4 axis combo and would like to also try the system with my parallel port computer. Any help with this will be greatly appreciated; my goal is to implement mach4.

Is there a test button on the laser tube power supply? You can test the laser output by using the test button. This will help you determine if the laser tube is bad, or if you have wiring issues. Sometimes, wiring to he TL may not work as some controllers are set to active low, so you may need to wire the controller to TH instead.

Additional Information:
Additionally, the mA on the high tension line does not have any relationship to the digital trigger signal from the controller to the power supply.

Click the link to add information to this solution:
I am building my own laser and have watch your trocen videos.....but laser wont fire...double checked wiring and all seems correct to diagram....but the kit i bought was for a 40 watt and i amd using a 60 watt power supply and tube.....What size does the power switching unit need to be ....I think mine is too small for the trigger mA

Sure, our blueChick and blackToe CNC Routers are considered relatively small machines at 1'x3' and 2'x4' respectively. They both use NEMA 23/24 motors. We recommend connecting the machines to either Mach3 or LinuxCNC and come with the necessary interface for either control software. You will need a computer for the control software and if you desire LinuxCNC, you will need a parallel port. Mach3 will accept either parallel port, or USB interface.

Click the link to add information to this solution:
I recently purchased the linksprite cnc engraving router and was wondering if your 3 axis small kit would be ok? the engraver came with nema 17 motors and a arduino board but but not liking the grbl control. could you point me in the right direction .Thanks.

If you would like to come to the office, please call the office at 281-815-7701 to request a visit at your specified time within our business hours so we can make sure that the right person will be there to assist you.

Click the link to add information to this solution:
I am considering the purchase of a Black foot or Green Bull CNC router and would like to come and visit your facility to see them in person and to discuss my requirements. Please can you tell me your address. I am based in NW Houston. Many thanks.

The blackFoot uses the same electronics and motors as the blackToe (2'x4') machine. The only parts that change are the gantry horizontal structural parts which may be relatively easy for you to change. We can send you those parts if you are interested in a smaller unit.

Click the link to add information to this solution:
I have a Blackfoot that was purchased in 2017, after the purchase we moved and I haven’t been able to find room for it... would you be interested in buying it back or trading for something smaller. The Blackfoot and computer have never run but I did purchase it assembled. Thanks in advance, scott

Here is the new link to the Planet CNC software download page: http://planet-cnc.com/software/

You can try the software as a demo however you will have limited g-code lines you can run. I believe it was around 500, so you can create small items with the demo.
To fully unlock the Planet-CNC software you will need to purchase the license.

Click the link to add information to this solution:
I purchased the USB BOB and the link for the Planet-cnc software is broke. Will I need to purchase a license for the software as well?

You can test the power supply, but you will need to take extra special care since the voltage on the high tension line can be lethal. Go to this instructable to see all the step on testing the power supply:

http://www.instructables.com/id/How-to-test-and-set-a-Chinese-China-made-CO2-Laser/?ALLSTEPS

Additional Information:

Click the link to add information to this solution:
I am building the Blacktooth laser cutter. What is the safest and most accurate way to test the output of the laser power supply WITHOUT connecting the laser tube? Can I use a standard multimeter and measure the voltage output of the laser power supply?

When dealing with 3rd party machines, we have a universal setup that will fit almost any other machine, although please take in consideration the specifications in which your stepper motors and drivers are used and set to!
Now changing the controls, would be more or less changing the Breakout board/interface board to a different one that might use a different program to run your machine. Usually you will not need to change your interface board or breakout board, unless the 3rd party manufacture made it specifically to that set up.

Click the link to add information to this solution:
I purchased a 3040 CNC router off eBay a year ago and would like to change the controls. The steppers are 185oz.in motors. My question do i need to purchase a interface board and break out boards?

with parallel port controllers, you have the ability to jog using two axes at the same time, but with USB controllers, this is not possible.

Click the link to add information to this solution:
[575] Hi, I recently purchased this board and everything seems to be fine! But I am not being able to jog two axis at same time as I used to do on my older board. Did I do something wrong?

The axis and connection information for the 3D Printer Main Board can be found here in the instructions below the product information.

https://www.buildyourcnc.com/item/3D-Printer-Component-electronicsAndMotors-3d-printer-mainboard-FDMElectronics-3dprintermainboard

Click the link to add information to this solution:
I purchased the driver boards and MB shield for the White Ant. None of the headers are labeled. Is there a diagram showing which headers is for which axis? Is there also a diagram showing which pin on the driver is ABCD? I have watched the vids and the boards in them do not match what was sent to me.

Many shielded cables come in various materials and designs, so having one with a copper mesh covering the inner insulator wire is no problem. We currently use a extension cord found locally at a hardware store and include one 18G wire for ground. So a specific shielded cable is not a required, unless being used next to specific and sensitive electronics that are extremely sensitive to noise and voltage interference than a shielded cable is required.

Click the link to add information to this solution:
I purchased a 2.2 spindle a while back and went to the electrical supply house to but shielded cable for the power run, I was on the web a while back and saw a picture of shielded cable that didn't look like what I had bought. should it have a copper like mesh wraped around the inner insulation. Thanks