[ Log In ]
[ Register ]

Question #: 192

Question: WHAT DOES FFC STANDS FOR

Current Solution

FFC stands for Film Finance Corporation

Respond:

Other Possible Solutions to this Question

  • What settings does I use for controlling the spindle in StepCon/Linuxcnc?

    LinuxCNC has excellent documents; however, I would like to offer our help in case you don't understand the information on that page. So, please use this FAQ (Question #: 13233) to state your questions by submitting additional information below.

    The LinuxCNC spindle control page is found here: http://linuxcnc.org/docs/html/examples/spindle.html

    Additional Information:
    After reading the LinuxCNC page my first questions would be can the spindle be controlled by PWM signal? Also, what pin on the parallel port would I set to Spindle Enable and FRW?

    Additional Information:
    To connect your computer to the VFD, use a USB to RS-485 interface. RS-485 is just a serial interface protocol that uses standard 0 to +5 voltage TTL signal levels for communication (as opposed to RS-232 which uses -12v and +12 for signal level changes).

    Get a high quality interface to reduce any issues during the process. The VFD should have two terminals labeled RS+ and RS-. The USB to RS-485 adapter should have this labeled on it as well so the connections should be relatively straight forward.

    In the VFD parameters:
    PD001: 2 to accept RS485 commands
    PD002: 2 to accept frequency comands
    PD163: 1 to RS485 slave address:1
    PD164: 1 RS485 baud rate 9600
    PD165: 3 8bit, no parity, 1 stop bit

    Make sure LinuxCNC is also set accordingly:

    The PIN14 and PIN16 in the stepconf wizard should be set to unused because you don't want LinuxCNC to be outputting unnecessary signals.

    In the options step of the stepconf wizard:
    - Check the Include Halui user interface component.
    - Check the Include custom PyVCP GUI panel.
    - Check Spindle speed display

    You will want to edit the custom.hal text file located in the folder that was created from the stepconf wizard. Add these following lines:
    loadusr -Wn vfd hy_vfd -n vfd -d /dev/ttyUSB0 -p none -r 9600
    net spindle-cmd-rpm-abs => vfd.speed-command
    net spindle-cw motion.spindle-forward => vfd.spindle-forward
    net spindle-ccw motion.spindle-reverse => vfd.spindle-reverse
    net on motion.spindle-on => vfd.spindle-on

    The dev folder in linux is typically used for interfacing devices and peripherals to the computer as these devices are communicated by simple memory addresses and these files are linked directly to these addresses.

    Under the custom_postgui.hal file, change this line:

    from: sets spindle-at-speed true
    to: net spindle-at-speed => cfd.spindle_at_speed

    and add the line:

    setp vfd.enable 1

    When you start LinuxCNC, you will a spindle section with the reverse and forward buttons, a stop button and - and + buttons. Use these buttons to conform that the spindle is functioning properly. The spindle speed indicator in LinuxCNC will show the spindle speed and you can confirm that this is equal to the speed indicated on the VFD.


    Credit for this helpful information goes to:


    Additional information was also added by us to provide a better understanding.

    Click the link to respond:
    What settings does I use for controlling the spindle in StepCon/Linuxcnc?

  • WHAT DOES COPYRIGHT MEAN

    Copyright, a form of intellectual property law, protects original works of authorship including literary, dramatic, musical, and artistic works, such as poetry, novels, movies, songs, computer software, and architecture. Copyright does not protect facts, ideas, systems, or methods of operation, although it may protect the way these things are expressed

    Click the link to respond:
    WHAT DOES COPYRIGHT MEAN

  • WHAT DOES YOUR HEART PUMP?

    Your heart pumps blood.

    Click the link to respond:
    WHAT DOES YOUR HEART PUMP?

  • WHAT DOES COPYRIGHT PROTECT?

    Copyright, a form of intellectual property law, protects original works of authorship including literary, dramatic, musical, and artistic works, such as poetry, novels, movies, songs, computer software, and architecture. Copyright does not protect facts, ideas, systems, or methods of operation, although it may protect the way these things are expressed

    Click the link to respond:
    WHAT DOES COPYRIGHT PROTECT?

  • what horizon does the sun set?

    The sun sets on the western horizon.

    Click the link to respond:
    what horizon does the sun set?

  • WHAT MOTORS DOES THE BLACK TOOTH USE?
  • WHAT MOTORS DOES THE BLACK TOOTH USE?
  • What does an electronics combo include?

    There are a few electronic combos that include various motors and drivers, but common to all of these are the power supply (36v) and breakout board. The most common combo is the standard 3-axis combo which includes three 425 oz-in motors and three 3.0 amp drivers. The heavy gantry combo includes one 651 oz-in motor and 6.0 amp driver and two 425 oz-in motors and two 3.0 amp drivers. The combo for the greenBull CNC Machine kit is three 651 oz-in motors and three 6.0 amp drivers.

    Click the link to respond:
    What does an electronics combo include?

  • what does the error code on my vfd mean?

    Remember, steps to correct and troubleshoot issues with any electrical devices should be done by a professional electrician.

    If you have an HY series VFD, the fault codes are below:

    OC-1: Over-current during ramp up or over-current at constant speed.
    Recommended actions: 1, 2, 3, 4

    OC-1: Over-current during ramp up or over-current at constant speed.
    Recommended actions: 1, 2, 5, 6

    OC-2: Over-current at deceleration or over-current at stop.
    Recommended actions: 1, 7, 2, 9, 10

    dL: Output short circuit.
    Recommended actions: 11, 1, 10

    Ou-1 or 2: Over-voltage at stop, over-voltage at acceleration, over-voltage at constant speed or over-voltage at deceleration
    Recommended actions: 12, 13

    Fb: Fuse break.
    Recommended actions: 14, 10

    Lu: Low voltage.
    Recommended actions: 15, 16, 17

    OH: Over heat of inverter.
    Recommended actions: 18, 19, 20

    OL-1: Inverter overload 150% per minute
    Recommended actions: 2, 21, 22

    OL-2: Motor overload 150% per minute.
    Recommended actions: 21, 23, 24, 25, 26, 21

    dT: Motor over-torque
    Recommended actions: 21, 23

    E.b.S.A or E.b.S.n or E.b.S.d or E.b.S.S: No feedback from the auxiliary coil or the lectromagnetic contactor
    Recommended action: 27

    bt: Braking transistor damage.
    Recommended action: 27

    CPu: CPU fault.
    Recommended action: 27

    E.E.E.S or E.E.E.n or E.E.E.d or E.E.E.A: EEPROM fault
    Recommended action: 27


    List of recommended actions:
    If error shows at ramp up or at constant speed:
    1. Check for a short circuit or partial short circuit and the insulation of the output wire is sufficient.
    2. Increase the capacity or the inverter if it is too small. Replace with an inverter that has a larger capacity
    3. Extend the ramp-up time
    4. Decrease the torque and increase the set value.
    5. Check if the motor is blocked and if there is a sudden change in load.
    6. Check if there is a sudden chance in the power supply voltage.
    7. Extend ramp down time
    9. DC breaking is too high. Decrease DC breaking
    10. Replace the inverter.
    11. Check to see if there is a short circuit with the connection wire of the motor.
    12. Extend the ramp-down time or add a breaking resistor.
    13. Check the mains supply voltage and insure there isn't ant sudden change in voltage.
    14. Send the inverter for repair.
    15. Check whether the input voltage is normal
    16. check whether there is a sudden change in load.
    17. Check whether there is any phase missing.
    18. Check the fan in the inverter. Is it spinning? Is it blocked? Does it have any foreign matter stuck on the fins of the fan? If so, clear the fan.
    19. Check the ambient temperature in the space that the inverter is placed.
    20. Check for adequate ventilation for the inverter where it is placed.
    21. Check for jamming or any sudden change with respect to mechanical load.
    22. Set the V/F curve correctly.
    23. The motor is too small.
    24. The motor is hot and the insulation of the motor degraded.
    25. Check if the voltage has a large variance.
    26. Check if there is a phase missing.
    27. Contact the supplier

    Additional Information:
    I have cnc wood carving machine 1325 the inverter showing error 0006

    Additional Information:
    What is uc3 error

    Additional Information:
    My inverter read error oc-1 high frequency how you can help me please


    Additional Information:
    My inverter read error oc-1 high frequency how you can help me please


    Additional Information:
    203

    Additional Information:
    E2 error

    Additional Information:
    Hello , I have an Redsail cnc and I get the following error " UC3 "after that the spindle stops arter a small knocking sound ,would there be an solution to this ?

    Additional Information:


    Additional Information:
    what does it mean when my spindle VFD shows E o and stops.


    Additional Information:
    Vfd er.01.5c

    Additional Information:
    CPFO error displayed reason

    Additional Information:
    Solve it

    Additional Information:
    My Spindle VFD Holip HLPA01D523C get error E.OC.A after factory reset. and now get error E.OC.n after i change the starting mode from Start from Starting
    Frequency to Frequency track start. whats wrong with the vactory setting?

    Additional Information:
    Er20

    Additional Information:
    Fault 503

    Additional Information:
    Fault 503

    Additional Information:
    What VFD do you have?

    Click the link to respond:
    what does the error code on my vfd mean?

  • What cnc machine does the plans refer to?

    The plans refer to the scratch build machine: http://www.buildyourcnc.com/cnckitintro.aspx and the one in the book "Build Your Own CNC Machine": http://www.buildyourcnc.com/Book.aspx

    Click the link to respond:
    What cnc machine does the plans refer to?

  • what horizon for sun set?

    The sun sets on the western horizon.

    Click the link to respond:
    what horizon for sun set?

  • how much is the planet-cnc key for the diy cnc? What does planet-cnc replace in standard cnc?

    The base price for planet cnc is 69 Euros, which translates to $85.85 dollars. Can be found here (http://www.planet-cnc.com/index.php?page=shop)

    Additional Information:


    Additional Information:

    Click the link to respond:
    how much is the planet-cnc key for the diy cnc? What does planet-cnc replace in standard cnc?

  • what does the plans, hardware, electronics and mechanical option consists of for a CNC router?

    The plans/hardware/electronics/mechanical includes everything but the wood structural components that can be cut by the customer. This plans/hardware option includes all of the electronics, like motors, drivers, controller, and all of the cables and wires to connect all of the electronics together. The mechanical components include shafts, couplings, linear rails, bearing blocks, sprockets, lead screws, etc. The hardware consists of all of the screws nuts, insert nuts, cross dowels, etc, to assemble all of the structural, mechanical, and electronics together.

    Click the link to respond:
    what does the plans, hardware, electronics and mechanical option consists of for a CNC router?

  • What do i need for a co2 laser

    To add CO2 laser functionality to your existing CNC machine, you will need everything listed on this page: https://www.buildyourcnc.com/LaserComponents.aspx

    The number of mirrors and mirror mounts will depend where and at what orientation the laser tube will be mounted in the machine. There is already a mirror mount in the head/nozzle unit, so keep that in mind.

    Click the link to respond:
    What do i need for a co2 laser

  • WHAT DO I SET FOR MY STEPS PER?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to respond:
    WHAT DO I SET FOR MY STEPS PER?

  • What size stepper motors does the blueChick use?

    The blueChick uses NEMA 23 425 oz/in motors.

    Click the link to respond:
    What size stepper motors does the blueChick use?

  • WHAT'S THE LEAD TIME FOR REDFROG?

    You can expect a two week lead time for the redFrog pick and place machine.

    Click the link to respond:
    WHAT'S THE LEAD TIME FOR REDFROG?

  • WHAT MACHINES DO WE SELL PLANS FOR

    Yes, the CNC machine hardware and plans combo is the same machine as in the book. The machine that we provide the plans for, can be found on the website, here http://buildyourcnc.com/Item/cnc-machine-scratchbuild

    Click the link to respond:
    WHAT MACHINES DO WE SELL PLANS FOR

  • WHAT ARE CHINA PRICES FOR COLLETS?

    From: Milan Shah
    ACCU-FIX Precision Tools Pvt Ltd
    458, Manjusar GIDC, Savli, Vadodara, Gujarat, India
    Mobile: +(91) 7567975718

    ER 11 - STD. Precision Collet $3.61 - No 1/2" shank sizes.
    ER 16 - STD. Precision Collet $4.05
    ER 20 - STD. Precision Collet $4.27
    ER 25 - STD. Precision Collet $4.34
    ER 32 - STD. Precision Collet $4.69
    ER 40 - STD. Precision Collet $5.32
    ---------------------------------------------------------------

    Click the link to respond:
    WHAT ARE CHINA PRICES FOR COLLETS?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.