Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

Dealing with our USB BoB, the potentiometer that will be used in the key jog, is a 5V, 5k - 10k Ohm potentiometer.

Click the link to add information to this solution:
I am building a cnc mill using your USB controller and i would like to know what is the specification of potentiometer used for adjusting manual axis jog speed

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I am making my own CNC setup using all the electronics from your website and I have many questions. Please advise how to have my computer recognize the USB connection from my breakout board also I would like to use a water cooled spindle but I need to know the parts required for a 4x10 bed area used for woods and plastics

Recommend first test to check a non-working axis, is to connect the current working axis(ex X-axis) to either the y/z axis to test the actual board and wiring in other axis setup. If tests failed and working (x-axis setup) does not working in the new axis location, go the Planet-CNC/File/Settings/Axes and check if your current non-working axis setup requires a inverted pulse. Check box and test again.
Next test if first fails, is to check continuity in your wires. A simple multimeter(ohm's) will work, just connect the positive and negative ends to one side of the same wire and if reading comes to 0.000, wire has continuity and if reads 0.L then there is a break in the wire and should be replaced.

Click the link to add information to this solution:
I installed the USB CNC Planet and got out of your USB controler $ 75 .Viska have linked to a video 'Party - 2.. X - running and y and z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work.

To get the activation code, all you need to do is plug the USB board into the computer using a USB cable, go to machine -> firmware -> update. After the firmware is updated the program will present to you a dialog box containing the activation code.

Additional Information:
MUAR-QVXU-CAYW-CBWQ


Additional Information:
MUIS-RQPB-PTHB-QTTB

Additional Information:
MUIH-EERP-IADB-TRIP

Additional Information:
9zYWBVf5TxKSK7hEr8gFX3EBw5wa0AMMllQqgftIAnKvZ8DXItLxaPbOB3jWvnpczl/sM/De0scRPHfSxWGmcA==

Additional Information:
Key: LUQR-BQYI-SCEW-QVBT

Additional Information:


Additional Information:
after i copy the code in the lower case i recived the same message (more than 8 times) ,, this is a evaluation...,, what i need to do to register properly?

Additional Information:
MUJR-BISM-KRDN-KKER
056971

Additional Information:
0561234

Additional Information:
MURL-QPQU-EGBJ-FNMB

Additional Information:
MUCE-LFMQ-WBCW-MLHO

Additional Information:


Additional Information:
LUTA-ADVJ-FXTW-FBCE

Additional Information:
LUTA-ADVJ-FXTW-FBCE

Additional Information:
looking for registration key for MUUK-IBTW-ECTL-CJWD

Additional Information:
MUXO-PIYY-KNHD-RKLY

Additional Information:
MUUE-YYCR-FCIC-VATK

Additional Information:
MUUE-YYCR-FCIC-VATK

Additional Information:


Additional Information:
MUEY-YLJU-OBRR-LJBV

Additional Information:
MUSP-JFDV-EKGQ-OVLW

Additional Information:
MUSP-JFDV-EKGQ-OVLW

Additional Information:


Additional Information:


Additional Information:
MULY-XRYF-BBDN-FBWP

Additional Information:


Additional Information:


Additional Information:
how to generate activation code richauto a11

Additional Information:
MUJC-LNIL-EOHS-YKNQ

Additional Information:
sdfd

Additional Information:
m l

Additional Information:
MUXC-RWKB-PKAL-HGNN

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Click the link to add information to this solution:
THEY ARE ASKING FOR THE ACTIVATION CODE AND SERIAL NUMBER USB BOARD. HOW CAN GET THAT INFORMATION?

The Federal Communications Commission (FCC) is the primary federal agency responsible for safety aspects of modern-day wireless telecommunications systems. The FCC's Internet address is shown below. Recently FCC published an excellent report, cited below, to assist citizens and local governments dealing with siting of telecommuncations towers. This report contains charts and figures describing the characteristics and performance of telecommunications antennas. The report also contains practical guidance on application of provisions of the Telecommunications Act of 1996, which is the governing legislation regarding safety and siting of wireless telelcommunications facilities. Web page: RF Safety Program Page. Report title: "A Local Government Official's Guide to Transmitting Antenna RF Emission Safety: Rules, Procedures, and Practical Guidance." The Local and State Government Advisory Committee (LSGAC) and the FCC have developed this guide to aid local governmental officials and citizens in understanding safety issues related to radiofrequency emissions from telecommunications towers. Gary Zeman, Sc.D., CHP Lawrence Berkeley National Laboratory

Click the link to add information to this solution:
I AM TAKING THE FINAL YEAR PROJECT IN BASE STATIONS AND AIR INTERFACE. WOULD LIKE TO HAVE SOME INFORMATION.

You can use the Pokeys57CNC board with our 3.0 amp drivers. The Pokeys57CNC has all of the headers necessary to provide the pulse train to any common stepper driver.

Here is the link to the Pokeys57CNC interface board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Here is the link to the 3.0 amp stepper motor driver:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-3!0a

Click the link to add information to this solution:
I'm planning on using your 425 oz motors and need help on selecting the right interface and driver boards. The PoKeys57 CNC USB card looks good but I wonder if the 2.5 amp driver boards shown with it are enough for the 3 amp motors?

For the USB controller and reversing the rotation for a motor, you would need to do this in the software (planet-cnc). In the configuration, you will need to reverse the direction by inverting the direction output.

Technically, the motor changes direction when the direction signal changes from a high to a low, or vice verse. For instance, the motor turns in one direction when the direction signal is, say, low. The motor will turn in the other direction when the direction signal is high. High is 5v and low is 0v or gnd.

Click the link to add information to this solution:
I have wired the step motors with the USB breakout board. When I jog the y axis it travels in the wrong direction. How do i switch the motors rotation?

Here is the answer to your first questions regarding the blueChick motors:
https://buildyourcnc.com/FAQ/9024

The shipping of the blueChick CNC will depend on if the machine is assembled or not. There is a duty for international orders, but I am unsure of the cost in other countries other than the US.

Thanks

Click the link to add information to this solution:
What are the specs for the stepper motors on the Bluechick? How much for shipping to Toronto, ON, Canada? Is there duty for shipping to Canada?

The USB interface only works with momentary switches unfortunately. If you have extensive knowledge of digital electronics, you can apply a receiver that uses a microcontroller and a transmitter with another microcontroller that produces the pulsing signal with the controls that you need.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I would like to make a handheld remote for the USB CNC Board using a joystick instead of momentary switches. Could you suggest one that will work with your board.

Your steps per inch will vary. I suggest watching my calibration video.

Click the link to add information to this solution:
I AM CURRENTLY HAVING SOME PROBLEM SQUARING THE GANTRY AND MY STEPS PER INCH ARE NOT 1422.22 ACCORDING TO YOUR CALCULATIONS IN AUTO SET UP THEY COME OUT LIKE 1416.#### THIS A BIG DEAL?

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I have your mach3 USB BoB, do you guys sell a torch control relay I can wire up to turn my plasma torch on and off and how I would wife that too this BoB?

The velocity is too high and/or the acceleration is too high and/or the axis is not calibrated and the motor is trying to move too fast, or trying to move too much inertia that the rated torque cannot overcome.

The recommended action would be to lower the velocity and the acceleration and do a calibration using the "set steps per unit" wizard on the settings tab of Mach3.

Once the calibration is completed and you have confirmed that the motor is moving the correct distance in reality compared to the DRO (digital readout) in Mach3, then you can increase the velocity and acceleration in the motor tuning section of Mach3 (config -> motor tuning).

Click the link to add information to this solution:
Developed an issue, when moving the y-axis it started to move, than stalled and sounded like gears grinding. Had to re-zero the y-axis. Using the USB controller with Mach3 software. What would cause this?

Recommend first test to check a non-working axis, is to connect the current working axis(ex X-axis) to either the y/z axis to test the actual board and wiring in other axis setup. If tests failed and working (x-axis setup) does not working in the new axis location, go the Planet-CNC/File/Settings/Axes and check if your current non-working axis setup requires a inverted pulse. Check box and test again.
Next test if first fails, is to check continuity in your wires. A simple multimeter(ohm's) will work, just connect the positive and negative ends to one side of the same wire and if reading comes to 0.000, wire has continuity and if reads 0.L then there is a break in the wire and should be replaced.

Click the link to add information to this solution:
I installed the USB CNC Planet software- 2.10.1406.1201., and got out of your USB controller $ 75. 00.All have linked like a video USB CNC Controller/Interface Wiring Instructions Part 2, X - running . Y, and Z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work.I used 425 oz-in motors

Yes, you can use 2 motors in the same axis output, however you will still need a driver for that motor! Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

Also you can run a slave motor using another axis on the board, and setting it up in the Planet-CNC settings.

Planet-CNC/File/Settings/Axes, here you will enter 3 in the Number of Axes location, and then change the Function of the Axis 4 to Slave 1. There you will have the 4th axis or A-axis be a slave for the x-axis.
Slave 1 - X-Axis
Slave 2 - Y-Axis
Slave 3 - A-Axis
Slave 4 - B-Axis
Etc...




Additional Information:
Do you act as if it's one motor and it goes to one controller on the motherboard?

Click the link to add information to this solution:
Can I run two stepper motors off the same axis output on the USB controller?

If your motors turn very slowly using your Mach3 USB board, then either the pulse from the board is being output at a slow rate or the motor drivers are set to a higher than expected microstepping:

The Mach3 USB board outputs the pulse rather than the computer, but Mach3 controls this pulse frequency within the motor tuning section. First, determine if the travel distance is correct with the computer and the physical travel of the machine.

If the travel is different, then your stepper motor driver's microstepping is incorrect, or the steps per inch/mm in the motor tuning within Mach3 is incorrect.

If the travel is correct, then simply change the velocity and acceleration parameters to your desired level. If Mach3 will not achieve the velocity you desire, then decrease your stepper motor driver's microstepping setting, readjust the step per inch/mm in mach3 and readjust the acceleration and velocity to your desired levels.

Additional Information:
Text is engraved in mirror image

Click the link to add information to this solution:
I have not used my CNC router (Mach3, USB interface board) for several months. When I tried to use it, all 3 stepper motors moved extremely slowly. Where should I start troubleshooting?