I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors.

Dealing with our USB BoB, the potentiometer that will be used in the key jog, is a 5V, 5k - 10k Ohm potentiometer.

Click the link to add information to this solution:
I am building a cnc mill using your USB controller and i would like to know what is the specification of potentiometer used for adjusting manual axis jog speed

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
Would I be able to use the Mach3 CNC Control Software or any of the CNC CAM Software(BOBCAD/CAM,CAMBAM) if I choose to use the Planet-CNC USB Interface Board?

A wireless MPG is generally independent of the controller since it communicates to Mach3 directly and does not pass through the controller. I am using a wireless MPG and I have no problems with either of the controllers that I sell (Mach3 USB controller or the Pokeys57CNC controller).

The issue you are having may be in the configuration of the wireless MPG that you are using.

Click the link to add information to this solution:
I am trying to decide which board I should use. I have a wireless MPG and every time I jog Z my X axis steps. If this is not a board issue I would like to go with a wired MPG. So I would like a board that I can have a wired MPG, use a tool touch off probe, control either spindle (VFD) on/off or on/off with speed control, and have homing switches.

I also place the controller very close to the drivers (on the back of the gantry). All of the cables are shielded. The only long cables are the mains power cables and the USB cable. The USB cable is shielded and contains active repeaters.

There is no problem putting all of the electronics in a box and using long cables to the motors. This is the way I did it for a very long time.

Click the link to add information to this solution:
Great site. I saw your videos of wiring the Mach3 USB controller. You place the drivers next to the Steppers. This means that you have very long leads to the USB Board? What about the placement of the controlling PC? Is it a problem to have the USB board, PSUs and Drivers in a control box and long leads to the steppers? Thank you.

You can download a trial version of PlanetCNC software from their site at http://www.planet-cnc.com/index.php?page=software to see how you like the interface. If you look at their main GUI screen, along the left side you will see 4 boxes labeled X,Y,Z and A. These represent the axes the software is equipped to control. (A being Axial, or rotational motion) Typically a separate motor and driver is used to control each axis. If you plan to switch axes you will need to connect and disconnect the outputs from your software to the drivers.

Click the link to add information to this solution:
sorry, this is what i meant to say: OK, so if I use the USB version then I would find the rotary/linear axis definitions in the planet cnc control software somewhere. I will be needing to change axis type often for various projects that is why I am asking.

The firmware update for the USB board is done by PlanetCNC. with your board hooked up to the computer via USB cable, log into PlanetCNC. Then, from the Machine tab on the toolbar choose firmware from the drop down and click on update.

Click the link to add information to this solution:
Is there a firmware update in the last two years for your USB board? If so how do we get it and install? If not do you expect any updates? If updates are released how do we find out?

Buying both the blackToe and the 4th axis is an available option, but take into account the clearance available on the gantry. The best option for the table will be a adjustable mid-section table. That will be able to lower when the 4th axis is going to be used. Or have a elongated table that has a portion for the basic CNC, then a section for the 4th axis.

Click the link to add information to this solution:
Would it be possible to buy the blackToe, and the 4th Axis, then build your own Tslot table to attach both items to? Would a setup like this be possible?

SketchUcam will output gcode which standard CNC control software will typically interpret, execute and control CNC machines. So, there is no problem using SketchUcam. However, our CNC machine control software that use our CNC machine interface boards require Windows OS, of Linux. The Mach3 USB board will only run with Mach3 control software which runs under the Windows OS. The parallel breakout board can run under Windows or Linux OS and the computer must contain a parallel port.

Click the link to add information to this solution:
I would like to know if your breakout board and driver boards are compatible with MAC OS X working with Sketch Up pro using SketchUcam ?

Yes, you can use a corner plate very easily. You will want to make a corner plate that has three independent plates that do not conduct with each other. Each of these plates will be connected to a different input (i.e. IN1 for X, IN2 for Y and IN3 for Z). The end mill or tool that is inserted into the spindle will connect to V- of the 24V power supply, or the DCM on the controller, which is connected to the 24V V-. Then, you can use the ref all home button on the program run screen of Mach3.

Click the link to add information to this solution:
I have the mach 3 USB board running a XYZ router, and a Z touch off (button style @ fixed position). I am wondering if there's a way to also use an X,Y plate that will only be responsible for corner finding. Is the digitize input the only input that can be used for a touch plate?

Yes, you can use a laptop if you have a controller that uses a USB, like the Mach3 USB card. If you don't have that, you can purchase that part here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

If you have a controller board that connects to a 25 pin connector, modern laptops will not be able to connect to that port.

How old is your CNC computer system?

Additional Information:
The CNC computer system is 2013 (5 years). The built in video card went out. I will order the Mach3 USB card. Thank you.

Additional Information:
You're welcome

Click the link to add information to this solution:
The motherboard on the computer I bought from you went out. What would you suggest. I have a laptop, could I use it and use a Mach3 USB interface board?

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

Click the link to add information to this solution:
I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I have your mach3 USB BoB, do you guys sell a torch control relay I can wire up to turn my plasma torch on and off and how I would wife that too this BoB?

Increasing the size on your Z-axis is possible by making the over z axis longer (rails, wood structure). Remember the location of your router/spindle and over all integrity of the z-axis structure.
Now another way of getting a longer reach is making a adjustable height table, so that you can raise or lower the material section(2' x 4') to add taller material or get a deeper cut.

Click the link to add information to this solution:
Is it possible to increase the Z axis on the Blacktoe 2x4? My ideal would be to have 8" of travel.

The USB interface only works with momentary switches unfortunately. If you have extensive knowledge of digital electronics, you can apply a receiver that uses a microcontroller and a transmitter with another microcontroller that produces the pulsing signal with the controls that you need.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I would like to make a handheld remote for the USB CNC Board using a joystick instead of momentary switches. Could you suggest one that will work with your board.

The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?