[ Log In ]
[ Register ]

Question #: 428

Question: HOW DO I SET UP MY MOTOR DRIVERS?

Current Solution

blueChick:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackToe:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackFoot:

X-axis
“CW8060 (6.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

greenBull:

X-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110
Mach3 Motor Tuning: 914.29 steps/in

Z-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/4 Microstep
Dipswitches: 01100100
Mach3 Motor Tuning: 1600 steps/in

Respond:

Other Possible Solutions to this Question

  • How can I connect my pc to my motor drivers and motors?

    All you need is a CNC controller like the following options:

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

    Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

    Click the link to add information to this solution:
    How can I connect my pc to my motor drivers and motors?

  • HOW MANY STEPS PER INCH DO I SET IN MOTOR TUNING?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:


    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    L8NiICEm

    Additional Information:
    -1 OR 2+427-427-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+145-145-1=0+0+0+1

    Additional Information:
    -1' OR 2+101-101-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+739-739-1=0+0+0+1 or 'kXOzulhF'='

    Additional Information:
    -1" OR 2+194-194-1=0+0+0+1 --

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:



    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    TO93cbNY

    Additional Information:
    -1 OR 2+824-824-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+681-681-1=0+0+0+1

    Additional Information:
    -1' OR 2+805-805-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+93-93-1=0+0+0+1 or 'MpFdFb3O'='

    Additional Information:
    -1" OR 2+275-275-1=0+0+0+1 --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    -1); waitfor delay '0:0:7' --

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(9),0))XOR"Z

    Additional Information:
    2k2XS4cL'; waitfor delay '0:0:15' --

    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:
    g7NWXuig'); waitfor delay '0:0:15' --

    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    XoN629J2')); waitfor delay '0:0:15' --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    -5 OR 247=(SELECT 247 FROM PG_SLEEP(15))--

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    -5) OR 122=(SELECT 122 FROM PG_SLEEP(15))--

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    -1)) OR 455=(SELECT 455 FROM PG_SLEEP(15))--

    Additional Information:
    o1WPxXu4'; waitfor delay '0:0:15' --

    Additional Information:
    X3pq07N4' OR 218=(SELECT 218 FROM PG_SLEEP(15))--

    Additional Information:
    i2jhQp7d'); waitfor delay '0:0:15' --

    Additional Information:
    xMv7x4te') OR 71=(SELECT 71 FROM PG_SLEEP(15))--

    Additional Information:
    IbKvmZZx')); waitfor delay '0:0:15' --

    Additional Information:
    YkhmkP9W')) OR 826=(SELECT 826 FROM PG_SLEEP(15))--

    Additional Information:
    -5 OR 539=(SELECT 539 FROM PG_SLEEP(15))--

    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:
    -5) OR 160=(SELECT 160 FROM PG_SLEEP(15))--

    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@EQr47

    Additional Information:
    -1)) OR 220=(SELECT 220 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 266=(SELECT 266 FROM PG_SLEEP(9))--

    Additional Information:



    Additional Information:
    -1)) OR 107=(SELECT 107 FROM PG_SLEEP(0))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    vL4vUHTG' OR 262=(SELECT 262 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    gGLXRSqE' OR 938=(SELECT 938 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    WT10Ii3x' OR 598=(SELECT 598 FROM PG_SLEEP(9))--

    Additional Information:



    Additional Information:
    QUuBKFso') OR 152=(SELECT 152 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    nI56G5Pp')) OR 493=(SELECT 493 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:



    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@nxzWO

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    vJlQYk5k

    Additional Information:
    -1 OR 2+406-406-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+236-236-1=0+0+0+1

    Additional Information:
    -1' OR 2+914-914-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+282-282-1=0+0+0+1 or '9J7jHjSj'='

    Additional Information:
    -1" OR 2+210-210-1=0+0+0+1 --

    Additional Information:



    Additional Information:



    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(14),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(0),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:



    Additional Information:



    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    RO4xZyuD'; waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    n2HpQRHN'); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    hd4dcDEY')); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    -5 OR 237=(SELECT 237 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    -5) OR 65=(SELECT 65 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 486=(SELECT 486 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 399=(SELECT 399 FROM PG_SLEEP(14))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    x4ZvP74B' OR 337=(SELECT 337 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    0VRZpjOv') OR 601=(SELECT 601 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    DrCdekI1')) OR 16=(SELECT 16 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    MQqu0z64')) OR 87=(SELECT 87 FROM PG_SLEEP(7))--

    Additional Information:



    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:



    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@HJ5oY

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    HOW MANY STEPS PER INCH DO I SET IN MOTOR TUNING?

  • 3d printer motors not moving fast enough. How should I configure the motor drivers?

    This will depend on the 3D printer that you are using and the mechanics involved. Specifically regarding the motor drivers, software is really what determines the speed of the motor. If the computer is not able to product the high number of pulses that is required for faster motion, then you can reduce the microstepping and configure the software appropriately for the new microstepping so the resolution is corrected (steps/inch or steps/mm).

    Click the link to add information to this solution:
    3d printer motors not moving fast enough. How should I configure the motor drivers?

  • How do I connect my motor wires to the driver?

    Use the datasheet associated to the motor that you purchased. Use the bipolar parallel configuration to optimum performance. The datasheets are located in their respective motor product pages. Just click on the motion electronics at the left and scroll down to the motor you have and click on the title, or datasheet link next to the motor. The datasheet will either be in the form of a pdf, or within the instructions on that product page.

    Additional Information:
    wiring diagram



    Additional Information:


    Additional Information:

    Click the link to add information to this solution:
    How do I connect my motor wires to the driver?

  • How can I control my motors and drivers from my pc?

    All you need is a CNC controller like the following options:

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

    Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

    Click the link to add information to this solution:
    How can I control my motors and drivers from my pc?

  • HOW DO I DETERMINE THE AMOUNT OF SCREW WEIGTH THAT MY MOTOR CAN HANDLE

    There are two main questions that we can answer with respect to motor torque and the mechanical advantage of lead screws, 1) What torque motor do you need to lift a particular weight, or 2) What maximum weight will my motor torque be able to lift.

    This formula uses Newtons (N) as it's final unit. Use this with the included radius (R) to determine the torque. Newtons can easily be converted to lbs or ounces using online conversions.

    Effort = Sf + (Load/(2 x pi x (R/p) x Se))

    where:
    p = pitch of the screw
    Se = screw efficiency = Standard lead screw will be between 20% (.2) and 40% (.4)
    Sf = static force. This is the force that is needed to start the movement. The number may be eliminated, but it is good to use a number in the 5 N to 20 N range.
    Load = the expected load that the effort will need to carry (i.e., the router and the included axis assembly that the motor will need to lift)
    R = radius of the lead screw


    This formula is based on the "law of the machine"

    The final effort amount with its unit of newtons and R will be the torque. For example, if the effort comes to 100 N (newtons) and the R is .5 inches, then you can assume that the effort is 50 N-in since it would take twice the effort to turn form the one inch mark from the center of the shaft.

    Example:

    Load = 90 N (20.2 lbs)
    R = 1 inch since that is the length from the center of the shaft that the motor is rated
    p = 1 inch / 13 = .08 inches

    Effort = 5 N + (90 N / (2 x 3.14 x (1 / .08) x .2))
    Effort = 5 N + (90 N / (6.28 x 12.5 x .2))
    Effort = 5 N + (90 N / (15.7))
    Effort = 5 N + (5.73 N)
    Effort = 10.7 N = 2.4 lbs = 38.4 oz-in

    I am putting the oz-in on the end because the formula considers the distance from the center of the shaft to be one inch.

    Therefore, a 425 oz-in motor would be able to lift a 20.2 lb Router with its accompanying assembly. If the assembly and router is heavier, plug in the numbers and determine the effort required.

    With a bit of algebra, the formula can be rewritten to find the load:

    Load = (Effort - Sf) x (2 x pi x (R/p) x Se)

    Another formula that does not consider friction at all:

    Effort = (Load x p) / (2 x pi x R)

    Lets see if we get similar results:

    Effort = (20 lb x .08 inches) / (2 x 3.14 x 1)
    Effort = 1.6 / 6.28 = .255 lbs = 4.08 oz-in

    The results from both formulas appear to be very small because a 13 TPI screw will have enormous mechanical advantage.

    It is evident that the first formula that does consider friction that we are loosely estimating is far more conservative than the second formula. Either way, even the most conservative formula shows that the 425 oz-in motor will handle very large weights. If you are using a lead screw with only two turns per inch, .5 inch pitch, you can determine the requirements with the first formula.

    Example for a 10 TPI 5 start (2 turns per inch) lead screw:

    Load = 90 N (20.2 lbs)
    R = 1 inch since that is the length from the center of the shaft that the motor is rated
    p = 1 inch / 2 = .5 inches

    Effort = 5 N + (90 N / (2 x 3.14 x (1 / .5) x .2))
    Effort = 5 N + (90 N / (6.28 x 2 x .2))
    Effort = 5 N + (90 N / (2.512))
    Effort = 5 N + (35.83 N)
    Effort = 40.828 N = 9.18 lbs = 146.88 oz-in

    Customer Response:
    thank you so much

    Additional Information:


    Additional Information:


    Additional Information:
    how do i calculate torque of stepper motor if lead screw coupled to motor shaft and load applied by lead screw on plate is 100 kg by vertically

    Additional Information:
    Pls


    Additional Information:
    1m 16mmdiameter ball screws calculations


    Additional Information:
    What is the max load that 2 NEMA 17 stepper motors (spaced 2 feet apart, both will be pushing up on the same gantry) can lift while using a rod with the following specifications T8 OD 8mm Pitch 2mm Lead 4mm for each motor.

    Click the link to add information to this solution:
    HOW DO I DETERMINE THE AMOUNT OF SCREW WEIGTH THAT MY MOTOR CAN HANDLE

  • HOW CAN I KNOW MUCH WEIGHT MY MOTOR CARRY?

    There are two main questions that we can answer with respect to motor torque and the mechanical advantage of lead screws, 1) What torque motor do you need to lift a particular weight, or 2) What maximum weight will my motor torque be able to lift.

    This formula uses Newtons (N) as it's final unit. Use this with the included radius (R) to determine the torque. Newtons can easily be converted to lbs or ounces using online conversions.

    Effort = Sf + (Load/(2 x pi x (R/p) x Se))

    where:
    p = pitch of the screw
    Se = screw efficiency = Standard lead screw will be between 20% (.2) and 40% (.4)
    Sf = static force. This is the force that is needed to start the movement. The number may be eliminated, but it is good to use a number in the 5 N to 20 N range.
    Load = the expected load that the effort will need to carry (i.e., the router and the included axis assembly that the motor will need to lift)
    R = radius of the lead screw


    This formula is based on the "law of the machine"

    The final effort amount with its unit of newtons and R will be the torque. For example, if the effort comes to 100 N (newtons) and the R is .5 inches, then you can assume that the effort is 50 N-in since it would take twice the effort to turn form the one inch mark from the center of the shaft.

    Example:

    Load = 90 N (20.2 lbs)
    R = 1 inch since that is the length from the center of the shaft that the motor is rated
    p = 1 inch / 13 = .08 inches

    Effort = 5 N + (90 N / (2 x 3.14 x (1 / .08) x .2))
    Effort = 5 N + (90 N / (6.28 x 12.5 x .2))
    Effort = 5 N + (90 N / (15.7))
    Effort = 5 N + (5.73 N)
    Effort = 10.7 N = 2.4 lbs = 38.4 oz-in

    I am putting the oz-in on the end because the formula considers the distance from the center of the shaft to be one inch.

    Therefore, a 425 oz-in motor would be able to lift a 20.2 lb Router with its accompanying assembly. If the assembly and router is heavier, plug in the numbers and determine the effort required.

    With a bit of algebra, the formula can be rewritten to find the load:

    Load = (Effort - Sf) x (2 x pi x (R/p) x Se)

    Another formula that does not consider friction at all:

    Effort = (Load x p) / (2 x pi x R)

    Lets see if we get similar results:

    Effort = (20 lb x .08 inches) / (2 x 3.14 x 1)
    Effort = 1.6 / 6.28 = .255 lbs = 4.08 oz-in

    The results from both formulas appear to be very small because a 13 TPI screw will have enormous mechanical advantage.

    It is evident that the first formula that does consider friction that we are loosely estimating is far more conservative than the second formula. Either way, even the most conservative formula shows that the 425 oz-in motor will handle very large weights. If you are using a lead screw with only two turns per inch, .5 inch pitch, you can determine the requirements with the first formula.

    Example for a 10 TPI 5 start (2 turns per inch) lead screw:

    Load = 90 N (20.2 lbs)
    R = 1 inch since that is the length from the center of the shaft that the motor is rated
    p = 1 inch / 2 = .5 inches

    Effort = 5 N + (90 N / (2 x 3.14 x (1 / .5) x .2))
    Effort = 5 N + (90 N / (6.28 x 2 x .2))
    Effort = 5 N + (90 N / (2.512))
    Effort = 5 N + (35.83 N)
    Effort = 40.828 N = 9.18 lbs = 146.88 oz-in

    Customer Response:
    thank you so much

    Additional Information:


    Additional Information:


    Additional Information:
    how do i calculate torque of stepper motor if lead screw coupled to motor shaft and load applied by lead screw on plate is 100 kg by vertically

    Additional Information:
    Pls


    Additional Information:
    1m 16mmdiameter ball screws calculations


    Additional Information:
    What is the max load that 2 NEMA 17 stepper motors (spaced 2 feet apart, both will be pushing up on the same gantry) can lift while using a rod with the following specifications T8 OD 8mm Pitch 2mm Lead 4mm for each motor.

    Click the link to add information to this solution:
    HOW CAN I KNOW MUCH WEIGHT MY MOTOR CARRY?

  • how do I connect an 8 wire motor to a driver?

    If the motor has 8 wires, you will need to wire the stepper motor in bipolar parallel. This motor (425 oz-in) is wired as follows:

    Red and Blue wires to A+ on driver
    Yellow and Black wires to A- on driver
    White and Brown wires to B+ on driver
    Orange and Green wires to B- on driver

    Click the link to add information to this solution:
    how do I connect an 8 wire motor to a driver?

  • HOW MUCH MOTOR CABLE DO I NEED FOR A BLACKFOOT

    The blackfoot requires a total of 50 feet of cable.

    The X axis needs 15 feet
    The Y axis needs 17 feet
    and the Z-axis needs 18 feet

    These are 20 gauge 4 conductor cable.

    Additional Information:

    Click the link to add information to this solution:
    HOW MUCH MOTOR CABLE DO I NEED FOR A BLACKFOOT

  • ok I Build my CNC machine table and now need a complete set for motor and software how you can help me

    Yes, I will need to know more specifics of the machine so I can recommend the correct electronics.

    Click the link to add information to this solution:
    ok I Build my CNC machine table and now need a complete set for motor and software how you can help me

  • I ordered the 3-axis medium stepper motor kit. The drivers i recieved were those for the 3-d printer main board, not the modular ones. How am i suppose to wire that up now?

    Please contact customerservice@buildyourcnc.com so we can assist you.

    Click the link to add information to this solution:
    I ordered the 3-axis medium stepper motor kit. The drivers i recieved were those for the 3-d printer main board, not the modular ones. How am i suppose to wire that up now?

  • HOW DO SET UP PUTTY FOR SERIAL COMMUNICATION?

    Under Connection -> Serial, configure the correct settings for the data frame

    Under Session, select Serial, the serial line "com" and speed should reflect the information set in the connection -> serial.

    Click the "Open" button to start the communication.

    Click the link to add information to this solution:
    HOW DO SET UP PUTTY FOR SERIAL COMMUNICATION?

  • Hi, I have one of your mach3 controller boards and have followed the tutorial videos but my motor drivers do not have p+ p- d+ d- I only have sted, dir, en and +5v

    Drivers will have terminals with labels that represent a pulse, clock or step, and for direction. Look at the following to determine which terminal is used for what purpose.

    Step- = CP- = P-
    Step+ = CP+ = P+
    Dir - = CW- = D-
    Dir+ = CW+ = D+

    Click the link to add information to this solution:
    Hi, I have one of your mach3 controller boards and have followed the tutorial videos but my motor drivers do not have p+ p- d+ d- I only have sted, dir, en and +5v

  • HOW DO I SET THE DIP SWITCHES?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:

    Click the link to add information to this solution:
    HOW DO I SET THE DIP SWITCHES?

  • I have my motors wired like the wiring diagram I have two motors on Y axis how do I wire the second motor

    To move two stepper motors simultaneously with the same signal, simply wire the two stepper motor drivers to the same interface board signal terminals (CP and CW).

    Additional Information:
    using a ardino uno controller and a cnc sheild on top of that how to wirer 2 motors to 1 axis its the x axis ?

    Click the link to add information to this solution:
    I have my motors wired like the wiring diagram I have two motors on Y axis how do I wire the second motor

  • How can I determine which wires on my stepper motor bellong to A+ A- B+ or B-?

    You can use a multimeter to determine the wires of the same coil (i.e A+ and A- belong to he same coil). The wires that are connected on the same coil will have relatively low resistance. A wire from one coil to another coil with have no continuity since the two coils are not touching each other.

    Click the link to add information to this solution:
    How can I determine which wires on my stepper motor bellong to A+ A- B+ or B-?

  • How do I wire my cnc electronics?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to add information to this solution:
    How do I wire my cnc electronics?

  • HOW DO I MAKE MY MACHINE SQUARE?

    I use a standard large "L" square used in construction. I run gantry up and down with the bit along one side of the square to make the square aligned with the x-axis. I then run the bit along the other edge and if I see space from the edge of the bit to the square, I adjust the gantry square by loosening and tightening the eye bolts that hold the chain at the ends of the table. Repeat as necessary to get the desired square.

    Additional Information:

    Click the link to add information to this solution:
    HOW DO I MAKE MY MACHINE SQUARE?

  • WHAT DO I SET FOR MY STEPS PER?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:


    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    L8NiICEm

    Additional Information:
    -1 OR 2+427-427-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+145-145-1=0+0+0+1

    Additional Information:
    -1' OR 2+101-101-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+739-739-1=0+0+0+1 or 'kXOzulhF'='

    Additional Information:
    -1" OR 2+194-194-1=0+0+0+1 --

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:



    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    TO93cbNY

    Additional Information:
    -1 OR 2+824-824-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+681-681-1=0+0+0+1

    Additional Information:
    -1' OR 2+805-805-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+93-93-1=0+0+0+1 or 'MpFdFb3O'='

    Additional Information:
    -1" OR 2+275-275-1=0+0+0+1 --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    -1); waitfor delay '0:0:7' --

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(9),0))XOR"Z

    Additional Information:
    2k2XS4cL'; waitfor delay '0:0:15' --

    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:
    g7NWXuig'); waitfor delay '0:0:15' --

    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    XoN629J2')); waitfor delay '0:0:15' --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    -5 OR 247=(SELECT 247 FROM PG_SLEEP(15))--

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    -5) OR 122=(SELECT 122 FROM PG_SLEEP(15))--

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    -1)) OR 455=(SELECT 455 FROM PG_SLEEP(15))--

    Additional Information:
    o1WPxXu4'; waitfor delay '0:0:15' --

    Additional Information:
    X3pq07N4' OR 218=(SELECT 218 FROM PG_SLEEP(15))--

    Additional Information:
    i2jhQp7d'); waitfor delay '0:0:15' --

    Additional Information:
    xMv7x4te') OR 71=(SELECT 71 FROM PG_SLEEP(15))--

    Additional Information:
    IbKvmZZx')); waitfor delay '0:0:15' --

    Additional Information:
    YkhmkP9W')) OR 826=(SELECT 826 FROM PG_SLEEP(15))--

    Additional Information:
    -5 OR 539=(SELECT 539 FROM PG_SLEEP(15))--

    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:
    -5) OR 160=(SELECT 160 FROM PG_SLEEP(15))--

    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@EQr47

    Additional Information:
    -1)) OR 220=(SELECT 220 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 266=(SELECT 266 FROM PG_SLEEP(9))--

    Additional Information:



    Additional Information:
    -1)) OR 107=(SELECT 107 FROM PG_SLEEP(0))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    vL4vUHTG' OR 262=(SELECT 262 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    gGLXRSqE' OR 938=(SELECT 938 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    WT10Ii3x' OR 598=(SELECT 598 FROM PG_SLEEP(9))--

    Additional Information:



    Additional Information:
    QUuBKFso') OR 152=(SELECT 152 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    nI56G5Pp')) OR 493=(SELECT 493 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:



    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@nxzWO

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    vJlQYk5k

    Additional Information:
    -1 OR 2+406-406-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+236-236-1=0+0+0+1

    Additional Information:
    -1' OR 2+914-914-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+282-282-1=0+0+0+1 or '9J7jHjSj'='

    Additional Information:
    -1" OR 2+210-210-1=0+0+0+1 --

    Additional Information:



    Additional Information:



    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(14),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(0),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:



    Additional Information:



    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    RO4xZyuD'; waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    n2HpQRHN'); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    hd4dcDEY')); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    -5 OR 237=(SELECT 237 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    -5) OR 65=(SELECT 65 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 486=(SELECT 486 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 399=(SELECT 399 FROM PG_SLEEP(14))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    x4ZvP74B' OR 337=(SELECT 337 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    0VRZpjOv') OR 601=(SELECT 601 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    DrCdekI1')) OR 16=(SELECT 16 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    MQqu0z64')) OR 87=(SELECT 87 FROM PG_SLEEP(7))--

    Additional Information:



    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:



    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@HJ5oY

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    WHAT DO I SET FOR MY STEPS PER?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.