[ Log In ]
[ Register ]

Question #: 430

Question: HOW DO I SET THE DIP SWITCHES?

Current Solution

blueChick:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackToe:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackFoot:

X-axis
“CW8060 (6.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

greenBull:

X-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110
Mach3 Motor Tuning: 914.29 steps/in

Z-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/4 Microstep
Dipswitches: 01100100
Mach3 Motor Tuning: 1600 steps/in

Additional Information:

Respond:

Other Possible Solutions to this Question

  • How should I connect the limit switches to my laser controller?

    If you are using the AWC708 or equivalent laser controller, the limit switches will connect between the EL input terminal and the GND terminal in normally open (NO) connection. Most limit switches can be connected as NO, or normally closed (NC).

    For instance, a limit switch for the X- limit will be connected from the ELX- terminal to the NO connection of the limit switch, then a connection from the GND terminal on the laser controller to the COM connection to the same limit switch.

    Click the link to add information to this solution:
    How should I connect the limit switches to my laser controller?

  • I bought a, 3-Axis NEMA23 CNC Kit (36V/9.7A/382oz-in/KL-4030.but dont know how to set the dip switches on my drivers. The place I bout the kit from isent very good and support.

    That driver (not purchased here) is a standard 3.0 amp driver that will have the dip switch settings on the top of the driver. You will need to determine the amp rating of you motor for the scheme that you wire your motor to the driver (bipolar parallel is recommended in most circumstances but can depend on your power supply output). Check the stepping motor datasheet for your motor to determine this amp rating.

    The other set of switches will be configure the microstepping. This will depend on your mechanical setup (i.e. lead screw, rack and pinion, roller chain, timing belt, etc.) and the specifications of such mechanical parts.

    This general formula (which can be searched using the Customer Service Live with many examples): step/inch = (natural motor steps * desired microsteps) / (mechanical travel for one motor rotation)

    Click the link to add information to this solution:
    I bought a, 3-Axis NEMA23 CNC Kit (36V/9.7A/382oz-in/KL-4030.but dont know how to set the dip switches on my drivers. The place I bout the kit from isent very good and support.

  • How do I wire the limit switches on the VLXL? Also, where do I place them? You included 2 rotary and two other limit switches.

    You can actually select many places for the switches, depending on where you think your zero will be. I will take pictures of where we positioned our switches. We set the positions so the zero is at the bottom left corner of the machine.

    Additional Information:
    I will take pictures tomorrow.

    Additional Information:
    Thank you. Just want to finish before the holiday.

    Additional Information:
    Not a problem at all and my apologies for not having that information. I have been meaning to put up a video on the limit switch connection as it is somewhat difficult to explain the process in words and diagrams.

    Additional Information:
    Any update?

    Additional Information:
    I plan on driving to the office later today and take pictures.

    Additional Information:
    Thank you. I've just done almost everything else. Just waiting for the grade 3 grease in the mail. Also, where do you suggest connecting the cable carriers? I ran everything through the top but the carrier is getting kind of full. Because of that, it is pushing the belt out when the gantry moves.

    Additional Information:
    I will take pictures of those connections as well.

    Additional Information:
    Much appreciated.

    Additional Information:
    It’s my pleasure.

    Additional Information:
    I’m almost to the office. I’ve been shuttling my kids around today. Sorry for the wait.

    Additional Information:
    I’m adding the images to the end of the VLXL instructions.

    Additional Information:
    The limit switch connections use the NO (Normally Open) terminals. That means that the switch, when not engaged, is normally open (no connection between the com and the NO terminal). When the switch is engaged, then the connection is closed and the NO and COM terminal become connected, making a circuit.

    Additional Information:
    Did you bend the arm on the x switch? Or can you mount it flush with enough give to trigger? Same on both sides?


    Additional Information:
    It does look like it is bent in the picture. No, you do not need to bend the arm of the rotary switch.

    Additional Information:
    We only have the rotary switch on one side.

    Click the link to add information to this solution:
    How do I wire the limit switches on the VLXL? Also, where do I place them? You included 2 rotary and two other limit switches.

  • Limit, E-stop and home switches: To set up the maximum number of switches set up I would need 2 BOB's, correct? How is this implimented and wired?

    The parallel breakout board allows for 4 input connections. Each input connection can have an unlimited number of switches, but if you need to separate the switch circuit for, say, all of the home switches, you can use another input pin. There is no need to add another breakout board to add more switches unless you need to use the input pins for totally unique conditions that may or may not be related to CNC functions.

    Customer response:
    To Clarify: I need to set up 3 home switches which can double for limits (that's 3 pins.). Another pin for a probe. That's 4 pins used. Now I need to set up the other limit and E-stop switches. No pins left, how do I do that? Can a ground pin be doubled up on?

    Plus, I have a SuperPID. Another pin?

    Additional answer:
    You can put all of your limit switches (including the E-stop which serves the same purpose as the limit switches) and home switches on a single pin. When homing, mach3 will move the axis it wants to home, hit the switch, pull away from the switch, then move the next axis and repeat the steps for the next two axes.

    The probe is on the 2nd pin. The SuperPID is on the 3rd pin and now you have another pin remaining.

    The GND terminal can be doubled up.

    Additional Information:
    how about a diagram to reference showing the pin-out to use

    Here is the diagram for the parallel breakout board (pins 10 through 13 are used for input):

    The circuit is from the GND to the input

    Here is the diagram for the Mach3 USB board (pins I1 through I4 are used for input):
    https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf
    The circuit is from the V- to the input pin

    Click the link to add information to this solution:
    Limit, E-stop and home switches: To set up the maximum number of switches set up I would need 2 BOB's, correct? How is this implimented and wired?

  • What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

    Any of the following power supplies will be fine for powering the Mach3 USB controller:
    https://www.buildyourcnc.com/item/24v

    however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
    https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

    Click the link to add information to this solution:
    What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

  • how do I build the blackfoot?

    the blackFoot is built using the online instructions found here: http://buildyourcnc.com/Item/cnc-machine-blackFoot-v4

    Click the link to add information to this solution:
    how do I build the blackfoot?

  • HOW DO I SET UP MY MOTOR DRIVERS?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in

    Click the link to add information to this solution:
    HOW DO I SET UP MY MOTOR DRIVERS?

  • how do I get the status of my order?

    If you are needing a status of an order that you purchased from us, you can either log-in and click on the "My Account" link at the top, or call us at 281-815-7701.

    The "My Account" link will contain all of the orders and tracking numbers associated with those orders. If the order does not contain a tracking number, call us to get a status of the order. In most cases, we will call you first if there is a backorder in our inventory.

    Click the link to add information to this solution:
    how do I get the status of my order?

  • How do I put two motors on the same axis

    Yes, you can use 2 motors in the same axis output, however you will still need a driver for that stepper motor. Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

    The wiring scheme would look like this:
    The step and direction output terminals on the CNC controller interface for the axis you want to have two motors would connect to both drivers of the two stepper motors on that axis.

    Additional Information:
    I have been running two motors from the same driver for 10 years on my 3m x 1.6m router. Both motors driving the gantry are wired together. I see no reason to use two drivers. The motors are high torque Nema 34. I've had no issues.

    Additional Information:

    Click the link to add information to this solution:
    How do I put two motors on the same axis

  • How do I wire two motors on the same axis?

    Yes, you can use 2 motors in the same axis output, however you will still need a driver for that stepper motor. Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

    The wiring scheme would look like this:
    The step and direction output terminals on the CNC controller interface for the axis you want to have two motors would connect to both drivers of the two stepper motors on that axis.

    Additional Information:
    I have been running two motors from the same driver for 10 years on my 3m x 1.6m router. Both motors driving the gantry are wired together. I see no reason to use two drivers. The motors are high torque Nema 34. I've had no issues.

    Additional Information:

    Click the link to add information to this solution:
    How do I wire two motors on the same axis?

  • How do I submit an idea in the R&D section?

    Click on the R&D menu selection. Log in, using the convenient log in section on that page and fill out the two questions pertaining to the research request.

    Click the link to add information to this solution:
    How do I submit an idea in the R&D section?

  • How do I connect a heated bed to the whiteant

    Connecting a heater bed to the whiteAnt is currently unavailable with our current version electronics, as we have tried to get around that issue here! We do not have the available slot for another thermocouple, so reading the temperature will not be possible for the heater bed. Also doubling the heater bed and extruder is not recommended, in which our current electronics will not be able to work with the additional heater bed.

    Click the link to add information to this solution:
    How do I connect a heated bed to the whiteant

  • how do I connect the parallel breakout board?

    You can go here to find the diagrams and instruction on connecting the parallel breakout board:

    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

    Also, please make sure to watch all of the electronics tutorial videos here:
    https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Click the link to add information to this solution:
    how do I connect the parallel breakout board?

  • How do I connect my motor wires to the driver?

    Use the datasheet associated to the motor that you purchased. Use the bipolar parallel configuration to optimum performance. The datasheets are located in their respective motor product pages. Just click on the motion electronics at the left and scroll down to the motor you have and click on the title, or datasheet link next to the motor. The datasheet will either be in the form of a pdf, or within the instructions on that product page.

    Additional Information:
    wiring diagram



    Additional Information:


    Additional Information:

    Click the link to add information to this solution:
    How do I connect my motor wires to the driver?

  • How do I interface to a laser with the Pokey57

    We have a video that shows the connection and implementation of a CO2 laser on the youtube channel here:

    &t=17s

    That video should show how I'm connecing the Pokeys57CNC to the laser tube power supply TL/TH terminal. I also show how to configure Mach3 to trigger the laser on and off using the M7 and M9 codes.

    Let me know if this helps.

    Click the link to add information to this solution:
    How do I interface to a laser with the Pokey57

  • HOW DO I WIRE FROM THE BREAKOUT BOARD TO DRIVER?

    CP+ to COM
    CP- to STEP
    CP+ to CW+ (small jumper wire)
    CW- to DIR

    Additional Information:
    If the driver does not have CP or CW labels, the CP is Step and the CW is Direction or DIR. If you connect the 5v to CP+ (or Step+) and CW+ (or DIR+) and the pin to CP- (or Step-) and another pin to CW- (or DIR-), then in software, the configuration for the step on that axis must be active low. Otherwise, if you connect the GND to CP- (or Step-) and CW- (or DIR-) and the pin to CP+ (or Step+) and another pin to CW+ (or DIR+), then in software, the configuration for the step on that axis must be active high.

    Additional Information:
    If you have a driver that is labeled pul, dir and ena: Pul+ is the Step+ and Pul- is the Step-. Pul is short for pulse. A pulse will create a step. Don't worry about the enable terminals.

    On the x-axis, pin #2 can go to pul- and pin #3 can go to dir-. The 5v will go to pul+ and dir+. The configuration for each axis for step will be active low and toggle active low for the dir on each axis to make it go in the direction desired.

    Additional Information:


    Additional Information:


    Additional Information:


    Additional Information:

    Click the link to add information to this solution:
    HOW DO I WIRE FROM THE BREAKOUT BOARD TO DRIVER?

  • HOW MANY STEPS PER INCH DO I SET IN MOTOR TUNING?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:


    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    L8NiICEm

    Additional Information:
    -1 OR 2+427-427-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+145-145-1=0+0+0+1

    Additional Information:
    -1' OR 2+101-101-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+739-739-1=0+0+0+1 or 'kXOzulhF'='

    Additional Information:
    -1" OR 2+194-194-1=0+0+0+1 --

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:



    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    TO93cbNY

    Additional Information:
    -1 OR 2+824-824-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+681-681-1=0+0+0+1

    Additional Information:
    -1' OR 2+805-805-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+93-93-1=0+0+0+1 or 'MpFdFb3O'='

    Additional Information:
    -1" OR 2+275-275-1=0+0+0+1 --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    -1); waitfor delay '0:0:7' --

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(9),0))XOR"Z

    Additional Information:
    2k2XS4cL'; waitfor delay '0:0:15' --

    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:
    g7NWXuig'); waitfor delay '0:0:15' --

    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    XoN629J2')); waitfor delay '0:0:15' --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    -5 OR 247=(SELECT 247 FROM PG_SLEEP(15))--

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    -5) OR 122=(SELECT 122 FROM PG_SLEEP(15))--

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    -1)) OR 455=(SELECT 455 FROM PG_SLEEP(15))--

    Additional Information:
    o1WPxXu4'; waitfor delay '0:0:15' --

    Additional Information:
    X3pq07N4' OR 218=(SELECT 218 FROM PG_SLEEP(15))--

    Additional Information:
    i2jhQp7d'); waitfor delay '0:0:15' --

    Additional Information:
    xMv7x4te') OR 71=(SELECT 71 FROM PG_SLEEP(15))--

    Additional Information:
    IbKvmZZx')); waitfor delay '0:0:15' --

    Additional Information:
    YkhmkP9W')) OR 826=(SELECT 826 FROM PG_SLEEP(15))--

    Additional Information:
    -5 OR 539=(SELECT 539 FROM PG_SLEEP(15))--

    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:
    -5) OR 160=(SELECT 160 FROM PG_SLEEP(15))--

    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@EQr47

    Additional Information:
    -1)) OR 220=(SELECT 220 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 266=(SELECT 266 FROM PG_SLEEP(9))--

    Additional Information:



    Additional Information:
    -1)) OR 107=(SELECT 107 FROM PG_SLEEP(0))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    vL4vUHTG' OR 262=(SELECT 262 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    gGLXRSqE' OR 938=(SELECT 938 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    WT10Ii3x' OR 598=(SELECT 598 FROM PG_SLEEP(9))--

    Additional Information:



    Additional Information:
    QUuBKFso') OR 152=(SELECT 152 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    nI56G5Pp')) OR 493=(SELECT 493 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:



    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@nxzWO

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    vJlQYk5k

    Additional Information:
    -1 OR 2+406-406-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+236-236-1=0+0+0+1

    Additional Information:
    -1' OR 2+914-914-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+282-282-1=0+0+0+1 or '9J7jHjSj'='

    Additional Information:
    -1" OR 2+210-210-1=0+0+0+1 --

    Additional Information:



    Additional Information:



    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(14),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(0),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:



    Additional Information:



    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    RO4xZyuD'; waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    n2HpQRHN'); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    hd4dcDEY')); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    -5 OR 237=(SELECT 237 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    -5) OR 65=(SELECT 65 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 486=(SELECT 486 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 399=(SELECT 399 FROM PG_SLEEP(14))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    x4ZvP74B' OR 337=(SELECT 337 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    0VRZpjOv') OR 601=(SELECT 601 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    DrCdekI1')) OR 16=(SELECT 16 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    MQqu0z64')) OR 87=(SELECT 87 FROM PG_SLEEP(7))--

    Additional Information:



    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:



    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@HJ5oY

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    HOW MANY STEPS PER INCH DO I SET IN MOTOR TUNING?

  • HOW DO DETERMINE THE STEPS PER INCH

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:


    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    L8NiICEm

    Additional Information:
    -1 OR 2+427-427-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+145-145-1=0+0+0+1

    Additional Information:
    -1' OR 2+101-101-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+739-739-1=0+0+0+1 or 'kXOzulhF'='

    Additional Information:
    -1" OR 2+194-194-1=0+0+0+1 --

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:



    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    TO93cbNY

    Additional Information:
    -1 OR 2+824-824-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+681-681-1=0+0+0+1

    Additional Information:
    -1' OR 2+805-805-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+93-93-1=0+0+0+1 or 'MpFdFb3O'='

    Additional Information:
    -1" OR 2+275-275-1=0+0+0+1 --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    -1); waitfor delay '0:0:7' --

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(9),0))XOR"Z

    Additional Information:
    2k2XS4cL'; waitfor delay '0:0:15' --

    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:
    g7NWXuig'); waitfor delay '0:0:15' --

    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    XoN629J2')); waitfor delay '0:0:15' --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    -5 OR 247=(SELECT 247 FROM PG_SLEEP(15))--

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    -5) OR 122=(SELECT 122 FROM PG_SLEEP(15))--

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    -1)) OR 455=(SELECT 455 FROM PG_SLEEP(15))--

    Additional Information:
    o1WPxXu4'; waitfor delay '0:0:15' --

    Additional Information:
    X3pq07N4' OR 218=(SELECT 218 FROM PG_SLEEP(15))--

    Additional Information:
    i2jhQp7d'); waitfor delay '0:0:15' --

    Additional Information:
    xMv7x4te') OR 71=(SELECT 71 FROM PG_SLEEP(15))--

    Additional Information:
    IbKvmZZx')); waitfor delay '0:0:15' --

    Additional Information:
    YkhmkP9W')) OR 826=(SELECT 826 FROM PG_SLEEP(15))--

    Additional Information:
    -5 OR 539=(SELECT 539 FROM PG_SLEEP(15))--

    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:
    -5) OR 160=(SELECT 160 FROM PG_SLEEP(15))--

    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@EQr47

    Additional Information:
    -1)) OR 220=(SELECT 220 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 266=(SELECT 266 FROM PG_SLEEP(9))--

    Additional Information:



    Additional Information:
    -1)) OR 107=(SELECT 107 FROM PG_SLEEP(0))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    vL4vUHTG' OR 262=(SELECT 262 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    gGLXRSqE' OR 938=(SELECT 938 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    WT10Ii3x' OR 598=(SELECT 598 FROM PG_SLEEP(9))--

    Additional Information:



    Additional Information:
    QUuBKFso') OR 152=(SELECT 152 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    nI56G5Pp')) OR 493=(SELECT 493 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:



    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@nxzWO

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    vJlQYk5k

    Additional Information:
    -1 OR 2+406-406-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+236-236-1=0+0+0+1

    Additional Information:
    -1' OR 2+914-914-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+282-282-1=0+0+0+1 or '9J7jHjSj'='

    Additional Information:
    -1" OR 2+210-210-1=0+0+0+1 --

    Additional Information:



    Additional Information:



    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(14),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(0),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:



    Additional Information:



    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    RO4xZyuD'; waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    n2HpQRHN'); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    hd4dcDEY')); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    -5 OR 237=(SELECT 237 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    -5) OR 65=(SELECT 65 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 486=(SELECT 486 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 399=(SELECT 399 FROM PG_SLEEP(14))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    x4ZvP74B' OR 337=(SELECT 337 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    0VRZpjOv') OR 601=(SELECT 601 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    DrCdekI1')) OR 16=(SELECT 16 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    MQqu0z64')) OR 87=(SELECT 87 FROM PG_SLEEP(7))--

    Additional Information:



    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:



    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@HJ5oY

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    HOW DO DETERMINE THE STEPS PER INCH

  • HOW DO I CONNECT A TOUCH PLATE TO THE BREAKOUT BOARD?

    The instructions on how to do this are found here, in these two videos, http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx

    Additional Information:

    Click the link to add information to this solution:
    HOW DO I CONNECT A TOUCH PLATE TO THE BREAKOUT BOARD?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.