[ Log In ]
[ Register ]

Question #: 489

Question: MOTOR WIRES FOR BLACKTOE

Current Solution

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Respond:

Other Possible Solutions to this Question

  • HOW LONG SHOULD THE MOTOR CABLES BE FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    HOW LONG SHOULD THE MOTOR CABLES BE FOR BLACKTOE

  • BLACKTOE MOTOR CABLE LENGTH

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    BLACKTOE MOTOR CABLE LENGTH

  • BLACKTOE MOTOR CABLE LENGTH

    The total length of cable for the greenBull 5x is 50 ft.
    Now the individual lengths for all three axis, is x=15 ft, y=17 ft, z=18 ft.

    Click the link to respond:
    BLACKTOE MOTOR CABLE LENGTH

  • BLACKTOE MOTOR CABLES

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    BLACKTOE MOTOR CABLES

  • BLACKTOE MOTOR CABLE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    BLACKTOE MOTOR CABLE

  • THE BLACKTOE REQUIRES HOW MUCH MOTOR CABLE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    THE BLACKTOE REQUIRES HOW MUCH MOTOR CABLE

  • WHAT IS THE LEAD TIME FOR BLACKTOE?

    You can expect a one week lead time for our machines.

    Click the link to respond:
    WHAT IS THE LEAD TIME FOR BLACKTOE?

  • WHAT IS THE LEAD TIME FOR BLACKTOE?

    You can expect a two week lead time for the redFrog pick and place machine.

    Click the link to respond:
    WHAT IS THE LEAD TIME FOR BLACKTOE?

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

  • What profile do I use in VCarve for a BlackToe?

    The blackToe is a CNC Router based on standard CNC Routing and milling actions. If you are referring to a profile machining operation (where the path follows the inside or outside edge of a polygon, line, arc or circle) then the profile is actually more a function what you want the CNC router (blackToe in this case) to do. A profile expects a specific end mill in the spindle and requires the specifications of the end mill in the profile operation.

    If you are referring to profile to mean "post processor" or specifications (profile of the control) for the g-code interpretation for a specific control program (like Mach3), then you will need to set the post processor in VCarve post-processor to the control program you are using.

    Please provide more specific information here so I can delve in a bit deeper.

    Click the link to respond:
    What profile do I use in VCarve for a BlackToe?

  • 100 oz-in motor wires to driver

    Black - A+, Green A-, Red B+, Blue B-

    Click the link to respond:
    100 oz-in motor wires to driver

  • Do you offer plans for the blackToe CNC Machine?

    The blackToe machine is offered as a kit only. We do have a machine that is build form plans. The plans refer to the scratch build machine: http://www.buildyourcnc.com/cnckitintro.aspx and the one in the book "Build Your Own CNC Machine": http://www.buildyourcnc.com/Book.aspx

    Additional Information:
    20

    Click the link to respond:
    Do you offer plans for the blackToe CNC Machine?

  • WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

    You can expect a one week lead time for our machines.

    Click the link to respond:
    WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

  • My question about motor tuning for the blacktoe in Mach 3 was for the aceleration and velocity settings what are the recomended settings

    In the customer service live, just enter "motor tuning" and it will give you a list of all the recommended or default settings for our machines. However the acceleration and velocity for the greenBull(other machines) will be an actual determination on your trials. You will want the highest possible acceleration and velocity without the motors stalling, so you can do increments of ten to be on the safe side, if it is too slow try increments of 25.

    The steps per inch is dependent on the microstepping:
    Steps/Inch for the x and y
    Steps = 200 motor steps per revolution x 16 microsteps = 3200 steps
    Inches = sprocket number of teeth x pitch of the sprocket = 14 x .25" = 3.5 inches
    steps/inch = 3200 / 3.5 = 914.28
    This is really a starting point. You will then need to use the mach3 calibration function to get the perfect steps/inch value. Use as long a measurement as possible when calibrating.

    Velocity:
    Start with a value of 1000 ipm. Increase this value with a relatively low acceleration at about 10. You will notice at a particular velocity that it will stall. This is your stall velocity. I would take the stall velocity and reduce it by about 30% to 50% which should give you a good final safe velocity.

    Acceleration:
    Once the velocity is found, raise the acceleration until it start to stall at a low velocity. Reduce the acceleration by about the same percentage to stick with a safe acceleration.

    The acceleration is mostly dependent on torque (current) and the top speed is dependent on the amount of voltage.

    Give some tests with all of the axes running at the same time. If you notice and stalling, reduce velocities and acceleration depending on when the stall happens (top end, or acceleration curve).


    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in
    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in
    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:


    Additional Information:
    4th axis


    Additional Information:

    Click the link to respond:
    My question about motor tuning for the blacktoe in Mach 3 was for the aceleration and velocity settings what are the recomended settings

  • WHAT LEAD TIME CAN EXPECT FOR BLACKTOE SO PICK UP THE MACHINE?

    You can expect a one week lead time for our machines.

    Click the link to respond:
    WHAT LEAD TIME CAN EXPECT FOR BLACKTOE SO PICK UP THE MACHINE?

  • How do I connect my motor wires to the driver?

    Use the datasheet associated to the motor that you purchased. Use the bipolar parallel configuration to optimum performance. The datasheets are located in their respective motor product pages. Just click on the motion electronics at the left and scroll down to the motor you have and click on the title, or datasheet link next to the motor. The datasheet will either be in the form of a pdf, or within the instructions on that product page.

    Additional Information:
    wiring diagram

    Click the link to respond:
    How do I connect my motor wires to the driver?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.