[ Register ]

### Question #: 490

Question: BLACKTOE MOTOR CABLES

Current Solution

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Respond:

### Other Possible Solutions to this Question

• HOW LONG SHOULD THE MOTOR CABLES BE FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

HOW LONG SHOULD THE MOTOR CABLES BE FOR BLACKTOE

• BLACKTOE MOTOR CABLE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

BLACKTOE MOTOR CABLE

• MOTOR WIRES FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

MOTOR WIRES FOR BLACKTOE

• BLACKTOE MOTOR CABLE LENGTH

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

BLACKTOE MOTOR CABLE LENGTH

• THE BLACKTOE REQUIRES HOW MUCH MOTOR CABLE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

THE BLACKTOE REQUIRES HOW MUCH MOTOR CABLE

• MOTOR 4 CONDUCTOR CABLES FOR BLACKFOOT

The blackfoot requires a total of 50 feet of cable.

The X axis needs 15 feet
The Y axis needs 17 feet
and the Z-axis needs 18 feet

These are 20 gauge 4 conductor cable.

MOTOR 4 CONDUCTOR CABLES FOR BLACKFOOT

• DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

Yes and properly soldered.

20

DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

• BLACKTOE CABLE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

BLACKTOE CABLE

• BLACKTOE REQUIRED HOW MUCH CABLE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

BLACKTOE REQUIRED HOW MUCH CABLE

• WHAT IS THE LEAD TIME FOR BLACKTOE?

You can expect a one week lead time for our machines.

WHAT IS THE LEAD TIME FOR BLACKTOE?

• WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

• WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

• WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

• WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

• WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

You can expect a one week lead time for our machines.

WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

• WHAT LEAD TIME CAN EXPECT FOR BLACKTOE SO PICK UP THE MACHINE?

You can expect a one week lead time for our machines.

WHAT LEAD TIME CAN EXPECT FOR BLACKTOE SO PICK UP THE MACHINE?

• MOTOR CABLE FOR BLACKFOOT

The blackfoot requires a total of 50 feet of cable.

The X axis needs 15 feet
The Y axis needs 17 feet
and the Z-axis needs 18 feet

These are 20 gauge 4 conductor cable.

MOTOR CABLE FOR BLACKFOOT

• WHAT MOTOR TUNING SETTINGS?

blueChick:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackToe:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackFoot:

X-axis
“CW8060 (6.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

greenBull:

X-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110
Mach3 Motor Tuning: 914.29 steps/in

Z-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/4 Microstep
Dipswitches: 01100100
Mach3 Motor Tuning: 1600 steps/in

Scratch-Build / Book-Build Kit:

X-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 1600 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

L8NiICEm

-1 OR 2+427-427-1=0+0+0+1 --

-1 OR 2+145-145-1=0+0+0+1

-1' OR 2+101-101-1=0+0+0+1 --

-1' OR 2+739-739-1=0+0+0+1 or 'kXOzulhF'='

-1" OR 2+194-194-1=0+0+0+1 --

if(now()=sysdate(),sleep(15),0)

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

-1; waitfor delay '0:0:15' --

TO93cbNY

-1 OR 2+824-824-1=0+0+0+1 --

-1 OR 2+681-681-1=0+0+0+1

-1' OR 2+805-805-1=0+0+0+1 --

-1' OR 2+93-93-1=0+0+0+1 or 'MpFdFb3O'='

-1" OR 2+275-275-1=0+0+0+1 --

-1); waitfor delay '0:0:15' --

if(now()=sysdate(),sleep(15),0)

-1); waitfor delay '0:0:7' --

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

-1); waitfor delay '0:0:15' --

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

-1)); waitfor delay '0:0:15' --

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

1 waitfor delay '0:0:15' --

0"XOR(if(now()=sysdate(),sleep(9),0))XOR"Z

2k2XS4cL'; waitfor delay '0:0:15' --

(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

g7NWXuig'); waitfor delay '0:0:15' --

-1; waitfor delay '0:0:15' --

XoN629J2')); waitfor delay '0:0:15' --

-1); waitfor delay '0:0:15' --

-5 OR 247=(SELECT 247 FROM PG_SLEEP(15))--

-1)); waitfor delay '0:0:15' --

-5) OR 122=(SELECT 122 FROM PG_SLEEP(15))--

1 waitfor delay '0:0:15' --

-1)) OR 455=(SELECT 455 FROM PG_SLEEP(15))--

o1WPxXu4'; waitfor delay '0:0:15' --

X3pq07N4' OR 218=(SELECT 218 FROM PG_SLEEP(15))--

i2jhQp7d'); waitfor delay '0:0:15' --

xMv7x4te') OR 71=(SELECT 71 FROM PG_SLEEP(15))--

IbKvmZZx')); waitfor delay '0:0:15' --

YkhmkP9W')) OR 826=(SELECT 826 FROM PG_SLEEP(15))--

-5 OR 539=(SELECT 539 FROM PG_SLEEP(15))--

-5) OR 160=(SELECT 160 FROM PG_SLEEP(15))--

1'"

1����%2527%2522

@@EQr47

-1)) OR 220=(SELECT 220 FROM PG_SLEEP(15))--

-1)) OR 266=(SELECT 266 FROM PG_SLEEP(9))--

-1)) OR 107=(SELECT 107 FROM PG_SLEEP(0))--

vL4vUHTG' OR 262=(SELECT 262 FROM PG_SLEEP(15))--

gGLXRSqE' OR 938=(SELECT 938 FROM PG_SLEEP(15))--

WT10Ii3x' OR 598=(SELECT 598 FROM PG_SLEEP(9))--

QUuBKFso') OR 152=(SELECT 152 FROM PG_SLEEP(15))--

nI56G5Pp')) OR 493=(SELECT 493 FROM PG_SLEEP(15))--

1'"

1����%2527%2522

@@nxzWO

vJlQYk5k

-1 OR 2+406-406-1=0+0+0+1 --

-1 OR 2+236-236-1=0+0+0+1

-1' OR 2+914-914-1=0+0+0+1 --

-1' OR 2+282-282-1=0+0+0+1 or '9J7jHjSj'='

-1" OR 2+210-210-1=0+0+0+1 --

if(now()=sysdate(),sleep(15),0)

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

0"XOR(if(now()=sysdate(),sleep(14),0))XOR"Z

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

0"XOR(if(now()=sysdate(),sleep(0),0))XOR"Z

(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

-1; waitfor delay '0:0:15' --

-1); waitfor delay '0:0:15' --

-1)); waitfor delay '0:0:15' --

1 waitfor delay '0:0:15' --

RO4xZyuD'; waitfor delay '0:0:15' --

n2HpQRHN'); waitfor delay '0:0:15' --

hd4dcDEY')); waitfor delay '0:0:15' --

-5 OR 237=(SELECT 237 FROM PG_SLEEP(15))--

-5) OR 65=(SELECT 65 FROM PG_SLEEP(15))--

-1)) OR 486=(SELECT 486 FROM PG_SLEEP(15))--

-1)) OR 399=(SELECT 399 FROM PG_SLEEP(14))--

x4ZvP74B' OR 337=(SELECT 337 FROM PG_SLEEP(15))--

0VRZpjOv') OR 601=(SELECT 601 FROM PG_SLEEP(15))--

DrCdekI1')) OR 16=(SELECT 16 FROM PG_SLEEP(15))--

MQqu0z64')) OR 87=(SELECT 87 FROM PG_SLEEP(7))--

1'"

1����%2527%2522

@@HJ5oY

WHAT MOTOR TUNING SETTINGS?

• MOTOR CABLE LENGTH FOR BLUECHICK

The recommended total length of motor cable should be 15 feet for the blueChick v4.2

Z - 6 feet
Y - 5 feet
X- 4 feet

20 AWG 4 conductor

If your drivers will be positioned farther from the machine, you may need longer cable.

MOTOR CABLE LENGTH FOR BLUECHICK

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales