[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 506

Question: HOW LONG SHOULD THE MOTOR CABLES BE FOR BLACKTOE

Current Solution

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Respond:

Other Possible Solutions to this Question

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

  • HOW MUCH MOTOR CABLE SHOULD PURCHASE FOR THE BLUECHICK

    The recommended total length of motor cable should be 15 feet for the blueChick v4.2

    Z - 6 feet
    Y - 5 feet
    X- 4 feet

    20 AWG 4 conductor

    If your drivers will be positioned farther from the machine, you may need longer cable.

    Click the link to respond:
    HOW MUCH MOTOR CABLE SHOULD PURCHASE FOR THE BLUECHICK

  • THE BLACKTOE REQUIRES HOW MUCH MOTOR CABLE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    THE BLACKTOE REQUIRES HOW MUCH MOTOR CABLE

  • BLACKTOE MOTOR CABLES

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    BLACKTOE MOTOR CABLES

  • How long should it take to build the vertical laser kit?

    Assembling the Vertical Laser XL machine will vary depending on your specific abilities. The length of time can be as short as one weekend, or as long as two weeks.

    Click the link to respond:
    How long should it take to build the vertical laser kit?

  • WHAT LENGTH OF MOTOR CABLE SHOULD BE USED WTIH THE BLUECHICK V4.2

    The recommended total length of motor cable should be 15 feet for the blueChick v4.2

    Z - 6 feet
    Y - 5 feet
    X- 4 feet

    20 AWG 4 conductor

    If your drivers will be positioned farther from the machine, you may need longer cable.

    Click the link to respond:
    WHAT LENGTH OF MOTOR CABLE SHOULD BE USED WTIH THE BLUECHICK V4.2

  • 3d printer motors not moving fast enough. How should I configure the motor drivers?

    This will depend on the 3D printer that you are using and the mechanics involved. Specifically regarding the motor drivers, software is really what determines the speed of the motor. If the computer is not able to product the high number of pulses that is required for faster motion, then you can reduce the microstepping and configure the software appropriately for the new microstepping so the resolution is corrected (steps/inch or steps/mm).

    Click the link to respond:
    3d printer motors not moving fast enough. How should I configure the motor drivers?

  • For tuning the motors in mach 3 should I be running a gcode or is keyboard jogging enough to determine the stall rates

    It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
    If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

    Click the link to respond:
    For tuning the motors in mach 3 should I be running a gcode or is keyboard jogging enough to determine the stall rates

  • For tuning the motors in mach 3 should I be running a gcode or is keyboard jogging enough to determine the stall rates

    Keyboard jogging will give you a good start at motor tuning since going from a stop to rapid travel speed is the quickest the machine will be required to accelerate. However, best practice is to also run test files and actually cut the type of materials you expect to deal with to test machine performance under load and make any fine adjustments needed for maximum performance.

    Click the link to respond:
    For tuning the motors in mach 3 should I be running a gcode or is keyboard jogging enough to determine the stall rates

  • MOTOR WIRES FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    MOTOR WIRES FOR BLACKTOE

  • Do you offer plans for the blackToe CNC Machine?

    The blackToe machine is offered as a kit only. We do have a machine that is build form plans. The plans refer to the scratch build machine: http://www.buildyourcnc.com/cnckitintro.aspx and the one in the book "Build Your Own CNC Machine": http://www.buildyourcnc.com/Book.aspx

    Additional Information:
    20

    Click the link to respond:
    Do you offer plans for the blackToe CNC Machine?

  • WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

    You can expect a one week lead time for our machines.

    Click the link to respond:
    WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

  • My question about motor tuning for the blacktoe in Mach 3 was for the aceleration and velocity settings what are the recomended settings

    In the customer service live, just enter "motor tuning" and it will give you a list of all the recommended or default settings for our machines. However the acceleration and velocity for the greenBull(other machines) will be an actual determination on your trials. You will want the highest possible acceleration and velocity without the motors stalling, so you can do increments of ten to be on the safe side, if it is too slow try increments of 25.

    The steps per inch is dependent on the microstepping:
    Steps/Inch for the x and y
    Steps = 200 motor steps per revolution x 16 microsteps = 3200 steps
    Inches = sprocket number of teeth x pitch of the sprocket = 14 x .25" = 3.5 inches
    steps/inch = 3200 / 3.5 = 914.28
    This is really a starting point. You will then need to use the mach3 calibration function to get the perfect steps/inch value. Use as long a measurement as possible when calibrating.

    Velocity:
    Start with a value of 1000 ipm. Increase this value with a relatively low acceleration at about 10. You will notice at a particular velocity that it will stall. This is your stall velocity. I would take the stall velocity and reduce it by about 30% to 50% which should give you a good final safe velocity.

    Acceleration:
    Once the velocity is found, raise the acceleration until it start to stall at a low velocity. Reduce the acceleration by about the same percentage to stick with a safe acceleration.

    The acceleration is mostly dependent on torque (current) and the top speed is dependent on the amount of voltage.

    Give some tests with all of the axes running at the same time. If you notice and stalling, reduce velocities and acceleration depending on when the stall happens (top end, or acceleration curve).


    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in
    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in
    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:


    Additional Information:
    4th axis


    Additional Information:

    Click the link to respond:
    My question about motor tuning for the blacktoe in Mach 3 was for the aceleration and velocity settings what are the recomended settings

  • how do I determine the steps per inch for the motors?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to respond:
    how do I determine the steps per inch for the motors?

  • WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • HOW MUCH MOTOR CABLE FOR THE BLACKFOOT?

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    HOW MUCH MOTOR CABLE FOR THE BLACKFOOT?

  • Can the Redleaf CPU be mounted in a vertical position so that motor cables run straight down?

    Absolutely. Everything in the redLeaf control box is securely fastened and can be mounted in any orientation.

    Check out this example where the Children's Museum of Houston mounted their redLeaf vertically.

    https://www.buildyourcnc.com/tutorials/Example-customer-blackfoot-houston-childrens-museum

    Click the link to respond:
    Can the Redleaf CPU be mounted in a vertical position so that motor cables run straight down?