Since you mentioned there is a nasty smell, I'm wondering if there might have been a issue with the power supply. Can you email us your name for the order and specific voltage you are using for the redFly? at techsupport@buildyourcnc.com. Also I want to mention if you have the USB cord plugged in to the redFly if it has the parallel interface board?

Click the link to add information to this solution:
When I first hooked up my redFly and was manually testing all the axes, everything was going well, then my Y axis stopped working all together, and now my X and Z have stopped also and my redFly has a nasty smell coming from it and none of the stepper motors seem to be getting power.

If your axis shutters and will not move unless moved by another force, that sounds like your acceleration is set too high. Lower the acceleration until it works well, then lower it a bit more to have a margin of safety.

IF that didn't work, try swapping the X and Y drivers. That way you will pinpoint if the issue is the driver. If the proplem persists, then there may be an issue with the motor itself.

The X and Y drivers can be easily swapped by swapping only the motor wires.

- Remove the x-axis motor wires from the X driver.
- Remove the Y motor wires from the Y driver.
- Insert the X motor wires into the Y driver.
- Insert the Y motor wires into the X driver.

Now the Y-axis will move the gantry. Test the Gantry movement by moving the Y axis using the up and down arrow keys (mach3).

Click the link to add information to this solution:
X AXIS STEPPER MOTOR STALLS AND SHUTTERS WHEN COMING FROM A STAND STILL WON'T MOVE WITHOUT PUSH BY HAND. I TOOK THE CHAINS OFF SPUN FINE WITH OUT LOAD. HAVE CHAIN HOOKED UP CAN MACHINE BACK FORTH HAND, NO HANG UPS OR ANYTHING, BUT TRY TO IT DOESN'T JUST SPINS OUT. ANY SUGGESTIONS?

It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

Click the link to add information to this solution:
I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

Click the link to add information to this solution:
I am using USB breakout board with planet-cnc software. When I enable jogging keyboard x axis starts to move by itself (whether keyboard connected of not). When I press stop - it stops for a moment and then starts to move again. What could that be? Tried to reinstall software - did not help.

You may want to try using a ferrite core or an inductor in addition to the shielded cable. Also, make sure you are grounding the shield at both ends. Even though this is not high frequency, grounding the shield at both ends in a motor scenario may help. Also, try to reduce any parallel wire runs.

Click the link to add information to this solution:
[575] Hi, I plug HY 220v spindle on the board. It work, but the is a unstable frequency on the spindle. I put shielded wires from BOB to Inverter, and from Inverter to Spindle. But the problem still there. I read that I have to put a Analogue PWM, is that true, or I have problem with my wires... Thank you

Dealing with our USB BoB, it is really similar to the MK1 board, but is also loosely based on their DIY board as well. We have not seen that much of jitters or jerks, that we have noticed here while fabricating and testing the boards. We have not heard that many issues dealing with the board about abnormalities in running, unless we have not been notified in regards to customers who have used them under continuous use.

Click the link to add information to this solution:
Its mentioned that your USB Breakout board is based on Planet-CNC's MK1 board. Planet-CNC on their forums mention that they've discontinued their MK1 because of a low buffer memory which caused jitters and jerks in the machine? Am I likely to face a similar problem with your board?

If you are using Mach3 do you have your hotkeys set up correctly?

Additional Information:
The office was closed on the weekends and during Dr. Martin Luther King Jr. Holiday.

Click the link to add information to this solution:
I got my Blackfoot 4.3 built. Hooked it to the Redleaf and when testing the axis controls Im able to move the X axis using the Right arrow key, but unable to move it with the left key. I have no control on my Y axis. Tried calling for tech support and recieve voicemail 2 days in a row after a few calls each day.

The fact that you cannot move the motors with the keyboard serves as a clue to a couple possibilities.

- The software may not be communicating with parallel port. (One possibility may be that your step pins are not low active, or vice versa depending on your drivers).
- You may not be in the correct tab of Mach3. Make sure you are in the Program Run tab.
- The jog on/off button on the program run screen may not be lit (invoked).

This address below shows the complete troubleshooting for this type of situation. It will show how to test each pin at the parallel port at the back of the computer and everything else associated with correctly wiring the electronics.

https://buildyourcnc.com/CNCElectronicsandWiring.aspx




Additional Information:
6 axis robot with Mach3 Card 6 Axis Motion Controller

Click the link to add information to this solution:
I bought Mach 4 and Mach 3 USB Motion card STB4100. The installation Manual you direct me to is for installing board with Mach3. Where can I find directions for the combination of products I bought? The axis motors are held stationary by the magnets but when I try to jog an axis from mach 4 program, no movement.

I am not using a parallell port. I am using a USB.

Click the link to add information to this solution:
I bought Mach 4 and Mach 3 USB Motion card STB4100. The installation Manual you direct me to is for installing board with Mach3. Where can I find directions for the combination of products I bought? The axis motors are held stationary by the magnets but when I try to jog an axis from mach 4 program, no movement.

If your axis shutters and will not move unless moved by another force, that sounds like your acceleration is set too high. Lower the acceleration until it works well, then lower it a bit more to have a margin of safety.

IF that didn't work, try swapping the X and Y drivers. That way you will pinpoint if the issue is the driver. If the proplem persists, then there may be an issue with the motor itself.

The X and Y drivers can be easily swapped by swapping only the motor wires.

- Remove the x-axis motor wires from the X driver.
- Remove the Y motor wires from the Y driver.
- Insert the X motor wires into the Y driver.
- Insert the Y motor wires into the X driver.

Now the Y-axis will move the gantry. Test the Gantry movement by moving the Y axis using the up and down arrow keys (mach3).

Click the link to add information to this solution:
X axis stepper motor stalls and shutters when coming from a stand still and won't move without a push by hand. I took the chains off and spun the motor fine with out a load. When I have the chain hooked up I can move the machine back and forth fine by hand, with no hang ups or anything, but when I try to have the motor move the machine it doesn't and just spins out. Any suggestions?

Make sure all your bolts/screws are tighten correctly and if using a lead screw make sure your anti-backlash nut is not offset. Now a default setting will be 10101100 for your driver dip switch settings and in motor tuning (mach3) 1600 steps per, 400.02 velocity, 4 in acceleration. now the acceleration and velocity can be adjusted to move your machine faster, but if set to high they could stall. Make sure you have the correct wiring from your motor to your driver (https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf).

Click the link to add information to this solution:
I have your Nema 24 electronics kit and am having problems with the Z axis dropping over time. I am using a PC 8902 motor. Any ideas on what the problem is? What should be the motor tuning values in Mach3? Thanks

We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

Here is a link to a tutorial for a DIY relay circuit:

Click the link to add information to this solution:
I am putting together the Blackfoot and I am using a porter cable router. I am confused on how to relay the routetr with the USB board. is there another relay switch that goes between the USB board and the router so that planet CNC can turn the router and perhaps the vacuum on and off?

If your laser machine needs to reflect off of three mirrors before it finally passes the focal lens, then I would recommend realigning the laser.

You might also want to see if the nozzle is hot. If so, then the laser energy is hitting some of the nozzle body and not all of the laser energy is exiting the small aperture of the nozzle. To determine if this is the cause, remove the nozzle and try the operation again to see if you have better results. If the results are better with the nozzle off, then realign the mirrors. If you are still having difficulty getting the laser energy to exit the nozzle, increase the diameter of the nozzle aperture.

If you are still having poor results, take a look at the focal lens and the mirrors for any debris. An unclean lens and mirrors are a common cause of poor lasing performance.

Click the link to add information to this solution:
Is this a problem with the tube or the power supply? The tube is illuminated but I don't get clear firing to the piece. This is a rastering work and I get faint results and then it will be fine, then nothing. Tube changes from pink to solid line purple even when vectoring or manually holding the fire button. https://youtu.be/rX5xZoM6_bk

We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

Here is a link to a tutorial for a DIY relay circuit:

Click the link to add information to this solution:
I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

It is not clear that mobile phones do produce brain tumors, or any serious health effects for that matter. A number of epidemiology studies have been almost completely negative on the issue.

See the article I wrote with John Moulder in IEEE Spectrum magazine and also Moulder's FAQ on mobile phones and health.

There has been a lot of discussion over the years about the possible mechanisms by which microwave energy such as emitted by cell phones might produce biological effects. The one unequivocal mechanism is the heating of tissue, but mobile phones operate at power levels that are too low to cause noticeable heating in the user. Scientists have speculated about other mechanisms, but these theories remain unproven and many of them have been challenged on biophysical grounds.

Whatever may be the risks or nonrisks of mobile phone radiation, a hands-free kit is an effective way for the user to reduce his or her exposure to radiofrequency energy while using a mobile phone.

Kenneth R. Foster, Professor
Department of Bioengineering
University of Pennsylvania

Click the link to add information to this solution:
I WOULD LIKE TO INQUIRE ABOUT THE PHYSICS PRINCIPLES REGARDING USE OF MOBILE PHONES AND DEVELOPMENT BRAIN TUMORS. I'VE BEEN THROUGH MANY SITES BUT THEY CAN NEVER GIVE AN EXACT ANSWER. REALLY SOMEONE TUMORS OR DOES IT HAVE DO WITH INTENSITY RADIATION DISTANCE BETWEEN PHONE INDIVIDUAL?

To home the z-axis using a plate:
- Connect the end mill using a large clamping device like an alligator clip with a wire connected to GND.

- Connect the plate (solder a wire to the plate) to one of the input pins.

- You can use the autoset to setup that pin in Mach3 simply by touching the two together once connected to the pin and GND.

Alternatively, the end mill can be connected to the pin and the plate connected to GND as long as there becomes a complete circuit when the end mill touches the plate.

To setup homing for the Planet-CNC homing and limits, go to the Planet-CNC Machine setup page which explains the process step by step: http://www.planet-cnc.com/faq/machine_setup/

Customer Response:
How do I get homing on z to work with planet cnc software using build your own usb board. I have gone to planet website and followed the instructions provided but my software will not allow entries in the required fields they are grayed out is it because I am not using planet-cnc's board, I have used this method for years with Mach3 and would like to use it with the usb board and software.

Answer:
Just received information from the developer. The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Click the link to add information to this solution:
How do I get Homing on Z to work with Plate and Ground using Buildyourcnc usb board all the entries for the sensor in planet-cnc are grayed out. I am using input z- and I purchased the software

Planet-cnc is the best place to get information on setting up the software for the USB interface. We will test the z-axis plate homing method on Monday to be able to provide a more thorough explanation.

Click the link to add information to this solution:
Has anyone at BuildYourCnc ever tested homeing the z axis using a plate and ground clip using their BuildYourCnc usb breakout Board and a registered copy of Planet-Cnc software. If the answer is yes could they provide instruction from BuildYourCnc and not Planet-Cnc as their instruction does not work with BuildYourCnc USB breakout Board.

Modifying the Z-axis to accommodate a larger motor will be a worth while task and is possible, however we have not calibrated the z-axis therefore using the 1600 Steps-per inch in the motor tuning on our machine in our shop. We have not noticed any significant depth increments from not calibrating the z-axis but only from zeroing the z axis too close to the material. Also in your design did you specify the actual depth and the length of tool (end mill/ bit) that you are using?

Click the link to add information to this solution:
I bought a Blacktoe 2 x 8 three years ago and have always had a problem with the Zid axis. No matter how tightly I've calibrated the axis it always cuts to deep. Can I put a larger Stepper motor on Z-axis using the same motion electronics that came with the original machine.