[ Log In ]
[ Register ]

Question #: 571

Question: HOW THE ROUTER IS CONNECTED TO ELECTRONICS?

Current Solution

The parallel breakout board has a relay that can turn the router on and off according to the control software in the computer. The router will turn on automatically prior to the machine moving (a time frame can be set so the router is up to speed). When the machine is finished and is not moving, the router automatically turns off. This is with the m3, m4, and m5 codes in the g-code.

If you are interested in the USB breakout board, you will need to get an independent relay board.

Respond:

Other Possible Solutions to this Question

  • HOW IS THE ROUTER CONNECTED TO ELECTRONICS?

    The parallel breakout board has a relay that can turn the router on and off according to the control software in the computer. The router will turn on automatically prior to the machine moving (a time frame can be set so the router is up to speed). When the machine is finished and is not moving, the router automatically turns off. This is with the m3, m4, and m5 codes in the g-code.

    If you are interested in the USB breakout board, you will need to get an independent relay board.

    Click the link to add information to this solution:
    HOW IS THE ROUTER CONNECTED TO ELECTRONICS?

  • HOW CAN THE ROUTER BE CONTROLLED OR CONNECTED TO ELECTRONICS COMPUTER?

    The parallel breakout board has a relay that can turn the router on and off according to the control software in the computer. The router will turn on automatically prior to the machine moving (a time frame can be set so the router is up to speed). When the machine is finished and is not moving, the router automatically turns off. This is with the m3, m4, and m5 codes in the g-code.

    If you are interested in the USB breakout board, you will need to get an independent relay board.

    Click the link to add information to this solution:
    HOW CAN THE ROUTER BE CONTROLLED OR CONNECTED TO ELECTRONICS COMPUTER?

  • IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER
  • WHAT IS THE DIFFERENCE BETWEEN PARALLEL AND USB ELECTRONICS COMBOS MOTOR KITS

    The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

    The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

    The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

    Additional Information:


    Additional Information:


    Additional Information:
    USB Motion controller breakout board work with planet cnc software?

    Click the link to add information to this solution:
    WHAT IS THE DIFFERENCE BETWEEN PARALLEL AND USB ELECTRONICS COMBOS MOTOR KITS

  • WHERE ARE THE ELECTRONICS WIRING VIDEOS?

    The blackFoot CNC machine kit does not include a table. The table can be made as long or shot as you need. for instance, if you are looking for a travel of 4 fet x 4 feet, then the table will need to be about 6 feet long to get the full 4 feet of travel.

    The electronics are very straight forward using the connection diagram for the breakout board that you select. Use the videos for a general idea and then use the connection diagram to verify the correct connections for the interface of your choosing.

    Yes,the USB interface replaces the breakout board, but remember that you will need to use the planet-cnc software with the USB interface.

    Additional Information:
    The electronics does accompany the cnc machine kits as long as you select the option "with electronics". There are option to purchase the machines without electronics and that would be necessary if you either have your own electronics, or you prefer the plug and play cnc computer system we call the redLeaf, or redSprout. This will also be necessary if you prefer the electronics that use the USB interface rather than the parallel interface.

    Additional Information:

    Click the link to add information to this solution:
    WHERE ARE THE ELECTRONICS WIRING VIDEOS?

  • WHERE ARE THE ELECTRONICS WIRING VIDEOS?

    The electronics and wiring videos are located under the tutorials section (click Tutorials on the top menu. The Title is "CNC Electronics and Wiring". The actual link to these videos is: https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Additional Information:
    You will also find the electronic wiring videos for the USB controller at: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

    Click the link to add information to this solution:
    WHERE ARE THE ELECTRONICS WIRING VIDEOS?

  • WHICH WIRES ARE CONNECTED TO THE EMERGENCY STOP BUTTON

    You can use one of the terminals on the input side of the breakout board to connect the e-stop switch.

    Additional Information:

    Click the link to add information to this solution:
    WHICH WIRES ARE CONNECTED TO THE EMERGENCY STOP BUTTON

  • DO NEED FAN FOR THE ELECTRONICS

    This will depend on your use. If you use the cnc all day every day, then I would recommend a fan. With the heat sinks exposed, they should do just fine.

    Click the link to add information to this solution:
    DO NEED FAN FOR THE ELECTRONICS

  • HOW CAN THE ROUTER BE CONTROLLED BY COMPUTER?

    The parallel breakout board has a relay that can turn the router on and off according to the control software in the computer. The router will turn on automatically prior to the machine moving (a time frame can be set so the router is up to speed). When the machine is finished and is not moving, the router automatically turns off. This is with the m3, m4, and m5 codes in the g-code.

    If you are interested in the USB breakout board, you will need to get an independent relay board.

    Click the link to add information to this solution:
    HOW CAN THE ROUTER BE CONTROLLED BY COMPUTER?

  • HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH

    The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

    Click the link to add information to this solution:
    HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH

  • DO HAVE TO REMOVE THE PORTER CABLE 892 ROUTER EVERY TIME CHANGE BIT?

    If you remove the dust shoe, you should be able to reach the collet to remove the end mill.

    Click the link to add information to this solution:
    DO HAVE TO REMOVE THE PORTER CABLE 892 ROUTER EVERY TIME CHANGE BIT?

  • HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

    The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

    Click the link to add information to this solution:
    HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

  • HOW TO KNOW IF THE POWER SUPPLY OF THE LASER TUBE IS DAMAGED

    This video will illustrate how to test for laser power:

    Click the link to add information to this solution:
    HOW TO KNOW IF THE POWER SUPPLY OF THE LASER TUBE IS DAMAGED

  • DOES THE PRICE OF 2’ X 4’ ROUTER INCLUDE EVERYTHING WOULD NEED TO START ROUTING?

    You will need the following:
    - router/spindle for the machine
    - computer to control the machine
    - construct a table if the optional table is not purchased
    - wire and cable to connect all of the electronics

    Additional Information:
    - software to run the gcode (purchased separately)

    Click the link to add information to this solution:
    DOES THE PRICE OF 2’ X 4’ ROUTER INCLUDE EVERYTHING WOULD NEED TO START ROUTING?

  • DOES THE PLUG AND PLAY ELECTRONICS COMPUTER FOR 3 AXIS CNC MACHINE HAVE ENOUGH MEMORY RAM ADDITIONAL SOFTWARE (BOBCAD-CAM, BOBART, MACH3) TO BE ADDED FUNCTION WELL?

    The plug and play system does have enough memory for additional software. The redLeaf comes standard with a 1TB hard drive.

    Click the link to add information to this solution:
    DOES THE PLUG AND PLAY ELECTRONICS COMPUTER FOR 3 AXIS CNC MACHINE HAVE ENOUGH MEMORY RAM ADDITIONAL SOFTWARE (BOBCAD-CAM, BOBART, MACH3) TO BE ADDED FUNCTION WELL?

  • HAVE 3D PRINTER THAT WANT TO MAKE CNC ROUTER ,IS THERE ANY GUIDES SHOW ME THE WAY

    What 3d printer do you have?

    Additional Information:
    whiteant

    Click the link to add information to this solution:
    HAVE 3D PRINTER THAT WANT TO MAKE CNC ROUTER ,IS THERE ANY GUIDES SHOW ME THE WAY

  • HOW DO YOU HOOK UP THE SPINDLE TO INVERTER?

    U - Pin1
    V - Pin2
    W - Pin3
    Pin4 Dead

    Additional Information:
    My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    HOW DO YOU HOOK UP THE SPINDLE TO INVERTER?

  • HOW TO HOOK UP THE VFD INVERTER WALL OUTLET?

    Input to VFD:
    240V Active - R
    240V Neutral - S
    Ground - E

    Additional Information:

    Click the link to add information to this solution:
    HOW TO HOOK UP THE VFD INVERTER WALL OUTLET?

  • DO NEED TO GET THE BIG PLANING BIT OR SURFACING AND GO OVER SPOIL BOARD MAKE SURE THAT IT IS PERFECTLY LEVEL IN RELATION ROUTER?

    Yes, that is highly recommended for all the reasons you can imagine. Say you were doing engraving, not surfacing the spoilboard will either exhibit some areas that have no engraving at all, or areas that have engraving that is too deep. If you are cutting completely through the material, then one end may be cut all the way through but the other end will not have a complete cut, or produce onion skinning on the bottom of the workpiece.

    Click the link to add information to this solution:
    DO NEED TO GET THE BIG PLANING BIT OR SURFACING AND GO OVER SPOIL BOARD MAKE SURE THAT IT IS PERFECTLY LEVEL IN RELATION ROUTER?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.