You can expect a two week lead time for the redFrog pick and place machine.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE LEAD TIME FOR REDFROG?

You can expect a two week lead time for the redFrog pick and place machine.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

You can expect a one week lead time for our machines.

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT IS THE LEAD TIME FOR BLACKTOE?

You can expect a one week lead time for our machines.

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT IS THE LEAD TIME FOR BLACKFOOT

You can expect a one week lead time for our machines.

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

You can expect a one week lead time for our machines.

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT LEAD TIME CAN EXPECT FOR BLACKTOE SO PICK UP THE MACHINE?

You can expect a two week lead time for the redFrog pick and place machine.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE PICK AND PLACE LEAD TIME?

The ALL POWERFULL!!!

Click the link to add information to this solution:
WHAT'S THE BRAIN

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT'S THE DIFFERENCE BETWEEN PARALLEL BREAKOUT BOARD AND USB ITERFACE?

The blackfoot requires a total of 50 feet of cable.

The X axis needs 15 feet
The Y axis needs 17 feet
and the Z-axis needs 18 feet

These are 20 gauge 4 conductor cable.

Additional Information:

Click the link to add information to this solution:
CABLE LENGTHS FOR THE BLACKFOOT

The parts list is located on this page: http://buildyourcnc.com/cnckitintro.aspx at the bottom of the description.

Additional Information:



Additional Information:

Click the link to add information to this solution:
PARTS LIST FOR THE BOOK MACHINE

This will depend on your use. If you use the cnc all day every day, then I would recommend a fan. With the heat sinks exposed, they should do just fine.

Click the link to add information to this solution:
DO NEED FAN FOR THE ELECTRONICS

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW MUCH MOTOR CABLE FOR THE BLACKFOOT?

The stamps.com technical support is developersupport@stamps.com

Click the link to add information to this solution:
WHAT THE TECHNICAL SUPPORT FOR STAMPS.COM?

The base greenLean CNC Machine Kit package includes:
- Structure (all of the structural parts that make up the gantry and rib system). The structure does not include the spoilboard.
- Hardware (All of the fasteners, like screws, nuts, cross dowels, washers, etc.)
- Mechanical components (bearings, rails, sprockets, shafts, etc.)
- Electronics (3 NEMA 651 Motors, 3 6.0 Amp drivers power supply, interface card to connect the drivers to a computer, and 91 feet of motor cable. Hookup wire to connect the electronics is not included.)
- 2.2kw Spindle and VFD

Here is a link to the greenLean CNC Macnine page: https://www.buildyourcnc.com/item/cnc-machine-greenLean-v1

Click the link to add information to this solution:
WHAT COMES IN THE BOX FOR BASIC GREENLEAN?

The total length of the brush strip for a 2.2kW spindle would be 17 1/4" inches.

Additional Information:
20

Click the link to add information to this solution:
LENGTH OF THE BRUSH STRIP FOR SPINDLE 2.2KW

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE