Yes, the CNC machine hardware and plans combo is the same machine as in the book. The machine that we provide the plans for, can be found on the website, here http://buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:



Additional Information:

Click the link to add information to this solution:
IS THE HARDWARE AND PLANS MACHINE SAME AS BOOK MACHINE?

It sounds like you got a misprinted book. If you purchased it from us, please contact us directly for a replacement. If you bought it from Amazon or a third party, you'll need to contact them. General information about lead screws is available on this website and at buildyourtools.com.

Click the link to add information to this solution:
Just bought Build Your own CNC Machine book. It is missing the chapter on lead screws that is described on page 181 at the end of Chaprer 16. Where can I get this info?

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
in your book - Build you own CNC Machine. Can I use 9/32" thick bearing instead of 1/4" thick?

You can use the board5.nc as the expansion parts.

Additional Information:
20

Click the link to add information to this solution:
Where is the link for the expansion kit for the CNC Routing Machine Kit Version 1.3?

Three 24" x 48" sheets of mdf is used for the book build or the combo #1 plans and kit.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
nt9ZbSRf

Additional Information:
-1 OR 2+534-534-1=0+0+0+1 --

Additional Information:
-1 OR 2+83-83-1=0+0+0+1

Additional Information:
-1' OR 2+658-658-1=0+0+0+1 --

Additional Information:
-1' OR 2+552-552-1=0+0+0+1 or '8QfEjrbS'='

Additional Information:
-1" OR 2+524-524-1=0+0+0+1 --

Additional Information:
if(now()=sysdate(),sleep(15),0)

Additional Information:
0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

Additional Information:
0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

Additional Information:
(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

Additional Information:
-1; waitfor delay '0:0:15' --

Additional Information:
-1); waitfor delay '0:0:15' --

Additional Information:
-1)); waitfor delay '0:0:15' --

Additional Information:
1 waitfor delay '0:0:15' --

Additional Information:
MXjE3Md3'; waitfor delay '0:0:15' --

Additional Information:
gont9Py6'); waitfor delay '0:0:15' --

Additional Information:
ixm7ZgaG'); waitfor delay '0:0:15' --

Additional Information:
L3WX2lOf')); waitfor delay '0:0:15' --

Additional Information:
-5 OR 669=(SELECT 669 FROM PG_SLEEP(15))--

Additional Information:
-5) OR 526=(SELECT 526 FROM PG_SLEEP(15))--

Additional Information:
-1)) OR 99=(SELECT 99 FROM PG_SLEEP(15))--

Additional Information:
B3hszLzc' OR 556=(SELECT 556 FROM PG_SLEEP(15))--

Additional Information:
K9OJrDz1') OR 613=(SELECT 613 FROM PG_SLEEP(15))--

Additional Information:
73wbJn3w')) OR 247=(SELECT 247 FROM PG_SLEEP(15))--

Additional Information:

*DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

Additional Information:

'||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

Additional Information:

'||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@zROBD

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW MUCH MDF IS USED FOR THE BOOK MACHINE COMBO #1

The blackToe machine is offered as a kit only. We do have a machine that is build form plans. The plans refer to the scratch build machine: http://www.buildyourcnc.com/cnckitintro.aspx and the one in the book "Build Your Own CNC Machine": http://www.buildyourcnc.com/Book.aspx

Additional Information:
20

Click the link to add information to this solution:
Do you offer plans for the blackToe CNC Machine?

The book design uses all NEMA 23/24 motors which can be found here:
https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

I recommend the Mach3 USB option as you will be able to use the USB connection for control.

If you are planning to build from the plans developed by the folks over at Woodsmith Magazine which is loosely based on the book design, use this electronics package:
https://buildyourcnc.com/item/electronicsAndMotors-3axis-heavy-gantry-elcombo

Click the link to add information to this solution:
Which electronics package is required for the CNC machine from the book designs?

We do not offer any free plans. We offer the CNC Scratch Build Kit which includes plans to build a CNC machine from scratch. You can find more information about this by clicking on this link https://buildyourcnc.com/cnckitintro.aspx

Additional Information:
WTF!! It says right on your utube page free plans available. I'll paste it from Utube right here.(DIY CNC Router for Under $900 - Free Plans Available) Very misleading, I spent a lot of time looking for this stuff and am lucky I found this because apparently none of its available for free. Very misleading, dishonest sales tactics. I'm sure you've made money conning honest people out of there money but your not gonna get shit from me. After reading what other people here have written, and the fact that you lie about the cost, at least on UTUBE, It is clear your a liar and a piece of shit. carry on though by all means and continue making money being a liar.

Additional Information:
So maybe you should edit your YT post that says you DO have free plans?

Click the link to add information to this solution:
I was told you have some free CNC machine plans. I can't find them. Where are they?

The electronics (stepper motors, drivers, power supply and interface board) can be found here:
https://www.buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

If your computer cannot connect to the parallel breakout board (the interface card), just make sure to inform us that you need the USB alternative.

Click the link to add information to this solution:
Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
I am building the CNC in your book - Build you own CNC Machine. One of the bearing thicknesses is 1/4" I can't find that bearing online. I can find 9/32, will that be a problem. Do you have a source? Thx

The scratchBuild page as listed above (link: https://buildyourcnc.com/cnckitintro.aspx), will have all the necessary hardware (bolts, screws, nuts, washers, etc) to finish the 2' x 4' scratchBuild CNC machine, with a DVD tutorial that will help you along the way.

Please read carefully, some items do not come included in the kit.
Listed materials of items not Included:
Computer of your choice that contains a parallel port
Router of your choice
Sheets of MDF for the structural parts
Aluminum Angles for rails (.75"x.75"x.125").
Lead screws (1/2" allthread/lead screw, or other of your choice). suggested lengths below:
X-Axis: ~52 Inches
Y-Axis: ~32 Inches
Z-Axis: ~14 Inches
Electronics

Click the link to add information to this solution:
I am following the build your own CNC book build for my first machine. Is the hardware on this page https://buildyourcnc.com/item/cnc-machine-scratchbuild the complete hardware kit (minus the items it already noted were not included) required for the build?

We currently do not sell any plan's for any of our machines, only for our scratch and build kit.

Click the link to add information to this solution:
Would you sell a kit that has all of the hardware and electronics with CNC plans for the table and gantry? Some of have access to a CNC temporarily (TechShop) but want one of our own.

The electronics combo with the sku of 101 on Amazon.com includes a parallel interface.

Click the link to add information to this solution:
I am looking at your 3 axis CNC machine kit(part #101) on Amazon. Is the interface on this kit USB?

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

Additional Information:

Click the link to add information to this solution:
THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

Absolutely! You can have almost unlimited limit switches and home switches on this controller. It all comes down to the wiring scheme used. I recommend the home switches be on separate input terminals. For example, IN1 would have the X home switch, IN2 would have the Y home switch and, IN3 would have the Z home switch if you plan on using home switches for the Z axis.

Adding the limit switches, these can be located on any input you want, even on the IN1, 2 or 3. The wiring scheme I like to use is as follows:
- IN1 has the X home, X limit ++, and X Limit --
- IN1 has the Y home, Y limit ++, and Y Limit --
- IN1 has the Z home, Z limit ++, and Z Limit --

In most cases, the Limit -- is the same switch as the Home switch.

These can be wired as NC (Normally closed) as a serial scheme, or as NO (Normally open) as a parallel scheme.

To understand the limits and wiring schemes, check out this video:

Click the link to add information to this solution:
[575] Hi, for the manage the limit switches, is it possible to have, for example, the same limit switch for X-- and X homing? And what is the configuration in mach3? In my CNC machine they are in the same position. Thank you

Mounting the extruder to the whiteAnt can be done a couple of ways. One is to take the 4 mounting holes located at the lower portion of the z-axis rail support and use long screws protruding out. Take a thinner material and drill the four holes matching the locations of the 4 screws and screw on nuts to hold it in place. The other option would be to use the metal bracket and fasten to the edge of the rail support.

Click the link to add information to this solution:
CAN YOU GIVE ME SOME HELP OR POINT IN THE RIGHT DIRECTION TO INCORPORATE MK 7 EXTRUDER WITH BOOK PLANS FOR 3D PRINTER?

Yes, that is not a problem at all. Give us a call.

Click the link to add information to this solution:
Can you custimize the 2'x4' CNC Machine Kit (blackToe v4.1) w/ 2.2kW Spindle into a 2'x3' Machine Kit?

The kit was designed to be hand cut, however if you want to get a CNC machine to cut it, you will have to add the dimension(etc.) Into the code of the CNC machine software to process and cut the MDF.
Since we do not provide the files/code.

Click the link to add information to this solution:
Do you all provide files to cut the MDF parts in the combo #1 on a CNC instead of having to hand cut them?

BYCNC Response:
The book build was intended to be 20 inches x 40 inches. Larger machines were designed after the book build was introduced so customers would have the option to go bigger than what the book offered. Check out our larger machines on the website as the machines sizes range from 1 foot x 3 feet all the way up to 6 feet x 12+ feet.

User Response:
I'm not wanting to spend $3,000+ on a machine, I want to build one that will do a 4x8 sheet of wood. Will the plans in the book scale up?

BYCNC Response:
It is possible to scale the book build up, but the rigidity of the gantry would be questionable at that span, even if the height of the gantry structure were to be increased. The gantry design would need to be modified to become a box shape rather than a flat configuration. The kits on the site were design for those wanting a larger machine.

Click the link to add information to this solution:
I BOUGHT YOUR BOOK AND WAS HOPEING IT HAD PLANS OR DIMENTIONS ON HOW TO BUILD A CNC HOLD 4X8 SHEET OF PLY. WILL THE IN SCALE UP?