[ Log In ]
[ Register ]

Question #: 588

Question: IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER

Current Solution

Check step 9 on this page: http://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Respond:

Other Possible Solutions to this Question

  • HOW THE ROUTER IS CONNECTED TO ELECTRONICS?

    The parallel breakout board has a relay that can turn the router on and off according to the control software in the computer. The router will turn on automatically prior to the machine moving (a time frame can be set so the router is up to speed). When the machine is finished and is not moving, the router automatically turns off. This is with the m3, m4, and m5 codes in the g-code.

    If you are interested in the USB breakout board, you will need to get an independent relay board.

    Click the link to add information to this solution:
    HOW THE ROUTER IS CONNECTED TO ELECTRONICS?

  • HOW IS THE ROUTER CONNECTED TO ELECTRONICS?

    The parallel breakout board has a relay that can turn the router on and off according to the control software in the computer. The router will turn on automatically prior to the machine moving (a time frame can be set so the router is up to speed). When the machine is finished and is not moving, the router automatically turns off. This is with the m3, m4, and m5 codes in the g-code.

    If you are interested in the USB breakout board, you will need to get an independent relay board.

    Click the link to add information to this solution:
    HOW IS THE ROUTER CONNECTED TO ELECTRONICS?

  • HOW CAN THE ROUTER BE CONTROLLED OR CONNECTED TO ELECTRONICS COMPUTER?

    The parallel breakout board has a relay that can turn the router on and off according to the control software in the computer. The router will turn on automatically prior to the machine moving (a time frame can be set so the router is up to speed). When the machine is finished and is not moving, the router automatically turns off. This is with the m3, m4, and m5 codes in the g-code.

    If you are interested in the USB breakout board, you will need to get an independent relay board.

    Click the link to add information to this solution:
    HOW CAN THE ROUTER BE CONTROLLED OR CONNECTED TO ELECTRONICS COMPUTER?

  • DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

    The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

    Click the link to add information to this solution:
    DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

  • I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

    We do have a relay board that words like a standard relay.

    Here is the URL of the relay board that we offer:

    https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

    Click the link to add information to this solution:
    I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

  • HAVE 3D PRINTER THAT WANT TO MAKE CNC ROUTER ,IS THERE ANY GUIDES SHOW ME THE WAY

    What 3d printer do you have?

    Additional Information:
    whiteant

    Click the link to add information to this solution:
    HAVE 3D PRINTER THAT WANT TO MAKE CNC ROUTER ,IS THERE ANY GUIDES SHOW ME THE WAY

  • HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

    Yes, our porter cable collets and nuts will fit the porter cable 7518.

    Additional Information:

    Click the link to add information to this solution:
    HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

  • DO HAVE TO REMOVE THE PORTER CABLE 892 ROUTER EVERY TIME CHANGE BIT?

    If you remove the dust shoe, you should be able to reach the collet to remove the end mill.

    Click the link to add information to this solution:
    DO HAVE TO REMOVE THE PORTER CABLE 892 ROUTER EVERY TIME CHANGE BIT?

  • I HAVE NOT SEEN ANY REFERENCES TO ENCODER FEED-BACK CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

    I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

    If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

    Click the link to add information to this solution:
    I HAVE NOT SEEN ANY REFERENCES TO ENCODER FEED-BACK CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

  • HOW TO KNOW IF THE POWER SUPPLY OF THE LASER TUBE IS DAMAGED

    This video will illustrate how to test for laser power:

    Click the link to add information to this solution:
    HOW TO KNOW IF THE POWER SUPPLY OF THE LASER TUBE IS DAMAGED

  • DOES THE PRICE OF 2’ X 4’ ROUTER INCLUDE EVERYTHING WOULD NEED TO START ROUTING?

    You will need the following:
    - router/spindle for the machine
    - computer to control the machine
    - construct a table if the optional table is not purchased
    - wire and cable to connect all of the electronics

    Additional Information:
    - software to run the gcode (purchased separately)

    Click the link to add information to this solution:
    DOES THE PRICE OF 2’ X 4’ ROUTER INCLUDE EVERYTHING WOULD NEED TO START ROUTING?

  • I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

    We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

    Here is a link to a tutorial for a DIY relay circuit:



    There is no vacuum control on the Planet-CNC program, however you could use the same concept of the router/spindle on/off using the relay circuit. Although you will have to use either the flood or mist function for the vacuum.

    Click the link to add information to this solution:
    I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

  • WHICH WIRES ARE CONNECTED TO THE EMERGENCY STOP BUTTON

    You can use one of the terminals on the input side of the breakout board to connect the e-stop switch.

    Click the link to add information to this solution:
    WHICH WIRES ARE CONNECTED TO THE EMERGENCY STOP BUTTON

  • I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

    Can you provide the model number of your VFD?

    Yes, I have the "YL600 - 2S - 2K20"

    It just came with a small booklet that is all in Chinese...

    Click the link to add information to this solution:
    I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

  • I HAVE NOT SEEN ANY REFERENCES TO STEPPING MOTOR ENCODER FEED-BACK FOR CLOSED LOOP CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

    I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

    If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

    Click the link to add information to this solution:
    I HAVE NOT SEEN ANY REFERENCES TO STEPPING MOTOR ENCODER FEED-BACK FOR CLOSED LOOP CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

  • HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

    The motor that is attached to the 4th axis is wired as follows:

    The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-

    Click the link to add information to this solution:
    HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

  • IF MY COMPUTER DOESN'T HAVE A PARALLEL PORT, HOW DO I RUN THE MACHINE?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Additional Information:

    Click the link to add information to this solution:
    IF MY COMPUTER DOESN'T HAVE A PARALLEL PORT, HOW DO I RUN THE MACHINE?

  • DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

    Yes, we have the optional table for the blackToe, but we need to fabricate it, which only takes one day. We generally reserve one week for the total fabrication and packing of all parts.

    Click the link to add information to this solution:
    DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

  • WAS WONDERING IF YOU COULD TELL ME WHETHER OR NOT SHIP ANY OF YOUR KIT PRODUCTS TO THE UK?

    You can determine if the area is serviceable by:
    - selecting the items you want to purchase on the website
    - go to the cart (shopping cart top left of any webpage)
    - log in, or register
    - Enter the address and click on calculate shipping.

    The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

    Click the link to add information to this solution:
    WAS WONDERING IF YOU COULD TELL ME WHETHER OR NOT SHIP ANY OF YOUR KIT PRODUCTS TO THE UK?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.