[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 592

Question: WHAT ARE THE BLACKTOOTH LENS SIZES AND FOCAL LENGTH SPECIFICATIONS?

Current Solution

The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

The mirrors are 25mm wide mirrors.

Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.

Respond:

Other Possible Solutions to this Question

  • What size and length of cable carrier suits the BlackTooth laser cutter?

    The space within the blackTooth laser cutter is so tight that a cable carrier will not fit.

    Click the link to respond:
    What size and length of cable carrier suits the BlackTooth laser cutter?

  • What are the specifications for the 2" strip brush as far as dimensions and width of the rubber top?

    The strip brush is .2 inches (5.23 mm) wide, so a slot of that width or slightly wider will work. We use a .25 inch groove and use glue to adhere the strip brushes in our dust shoe.

    The material of the bristles and the strip that holds the bristles are nylon.

    Click the link to respond:
    What are the specifications for the 2" strip brush as far as dimensions and width of the rubber top?

  • WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

    Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

    Click the link to respond:
    WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

  • please provide pdf documentation, at lease requirements and specifications, for 24" x 20" blackTooth Laser Cutting and Engraving System

    We do not provide any .pdf, requirements or specifications for any CNC machines we have on the market, for DIY builds. Currently you can view all the information we have for viewing purposes on our blackTooth here:(https://buildyourcnc.com/Item/cnc-machine-blacktooth-laser-cutter-engraver-40w) and is available for purchase as a DIY kit.

    This laser system can work in a house environment or a shop environment, this machine can also run in either 110V or 220V.

    Click the link to respond:
    please provide pdf documentation, at lease requirements and specifications, for 24" x 20" blackTooth Laser Cutting and Engraving System

  • what are the specs of the blacktooth laser cutter (dimensions and weight) when assembled?

    The blackTooth envelope dimensions and weight:

    - Length and width: 37" x 34"
    - The height: 11.25"
    - The weight: 70 lbs.

    Click the link to respond:
    what are the specs of the blacktooth laser cutter (dimensions and weight) when assembled?

  • I have been asked to provide an exhaust for the Blacktooth Laser Cutter CO2 40W. I see no specifications or guidelines for exhausting fumes from the machine. Can someone help me?

    Exhausting the blackTooth laser cutter is a very important consideration and should be taken seriously, especially if you are cutting materials that give off toxic fumes when the material is burned. You will want a 4 inch hose to connect from the blackTooth to a blower, and another 4 inch hose to connect from the blower to the outside. The blower should be sufficient to provide completely negative pressure within the laser enclosure so there will be no escape of gasses.

    The connections at the machine, at the blower and at the location the hose exhausts outside should be thoroughly checked for leaks. Use a gasket, or silicone. Once complete, try cutting a non-toxic material that will give off an odor (wood, or non-toxic plastic) and try the system and determine if the smell is present.

    Click the link to respond:
    I have been asked to provide an exhaust for the Blacktooth Laser Cutter CO2 40W. I see no specifications or guidelines for exhausting fumes from the machine. Can someone help me?

  • WHAT IS LASER AND LENS FOCAL LENGTH?

    The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

    The mirrors are 25mm wide mirrors.

    Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.

    Click the link to respond:
    WHAT IS LASER AND LENS FOCAL LENGTH?

  • WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

    If you take the standard parallel cable BoB (Break Out Board), then you will need control software (Mach 3 or EMC2) and CAM software to make your G-Code (such as CamBam). Personally I use CamBam and Mach 3, they work beautifully but don't expect to turn them on and know how they work out of the box. Give yourself a few weeks to get familiar with the basics. CamBam is VERY powerful software for it's price. I'm surprised how much I keep learning on what I can do with it...I highly recommend it if you want as much control as possible.

    Mach 3 + CamBam as a bundle costs $310. EMC2 will give you a free replacement for Mach 3 and is exclusively for Linux.

    If you use the USB BoB, it will cost an extra $75 + $75 for the software. This is an all-in-one package so no need for Mach 3 or CamBam.

    For etching rasters (jpeg, bmp, tiff, non-vectors, photos), I highly recommend PicEngrave. It has been a labor of love for the past 9 years and John has done a wonderful job with it. It easily compares in quality compared to software that is in the $200-$300 range. John's software runs $40 and can be found here: http://picengrave.com/ (don't let the modest website fool you, this stuff can do amazing things). DotG and the Mach3 engrave plugin are two other options and instructions can be found on Dustans page in the gallery on buildyourcnc.com website.

    Click the link to respond:
    WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

  • WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

    I would say mechanically, between the official build instructions, Warren's awesome blog (http://blacktoothlaser.blogspot.com/) and the tips in the forum, the blackTooth is a really simple build. The challenges come with electronics and software. There's a number of different ways to drive the laser and motors. A decent understanding of electronics and computers is a must.

    Click the link to respond:
    WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

  • WHAT ARE SOME USEFUL MODIFICATIONS CAN APPLY TO THE BLACKTOOTH LASER CUTTER?

    Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

    Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

    Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

    Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

    Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

    To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

    A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

    Click the link to respond:
    WHAT ARE SOME USEFUL MODIFICATIONS CAN APPLY TO THE BLACKTOOTH LASER CUTTER?

  • What´s the size and weight of the blacktooth shipping box?

    For our blackTooth laser cuter and engraver, the specified packages in shipment may vary to option chosen and additional purchases.

    3 packages:
    40" x 21" x 5"/54 lb.
    17" x 12" x 12"/27 lb.
    40" x 10" x 7"/5 lb.

    Click the link to respond:
    What´s the size and weight of the blacktooth shipping box?

  • what is the size/width of pulley and timing belt used in Blacktooth laser cutter ?

    The blackTooth uses MXL timing belt with 1/4" MXL Drive Pulley 20 teeth.

    Click the link to respond:
    what is the size/width of pulley and timing belt used in Blacktooth laser cutter ?

  • what is the physical size of the blacktooth area with the working size of 20 x 23"?

    The blackTooth work-space area and travel (X and Y axis travel) is 20" x 24"

    Click the link to respond:
    what is the physical size of the blacktooth area with the working size of 20 x 23"?

  • whatt is the physical size of the blacktooth area with the working size of 20 x 23"?

    To allow a 4'x8' stock to be used by a blackTooth laser system, you will need to cut the large sheet with a standard woodworking tool such as a hand saw, circular saw, table saw, jig saw, etc. Alternatively, you can purchase our very affordable 4'x8' vertical laser systems that allows a 4'x8' sheet stock.

    Click the link to respond:
    whatt is the physical size of the blacktooth area with the working size of 20 x 23"?

  • WHAT ARE THE BLACKTOOTH SHIPPING DIMENSIONS?

    The blacktooth ships in 3 boxes.

    Structure 38x22x5 #54

    Components 14x13x13 #30

    Laser Tube 35x7x6 #4

    Click the link to respond:
    WHAT ARE THE BLACKTOOTH SHIPPING DIMENSIONS?

  • What kind of computer comes with the blacktooth and do i need to install windows after purchase?

    For the integrated computer for the blackTooth, the hard drive doe not need to be formatted, but will require an OS (operating system) to be installed. Ubuntu Linux can be installed with the CNC integrated software from Linuxcnc.org. Windows can also be installed.

    Click the link to respond:
    What kind of computer comes with the blacktooth and do i need to install windows after purchase?

  • Can we order a preassembled version of the blacktooth laser cutter and what would the lead time be.

    We do have the option of assembled blackTooth CNC.
    For further information on lead time and quote; please email (customerservice@buildyourcnc.com)

    Click the link to respond:
    Can we order a preassembled version of the blacktooth laser cutter and what would the lead time be.

  • I believe I understand USB v Parallel BoB on the Blacktooth but what is "integrated computer" mean?

    Integrated computer for our blackFoot means, that the computer components will be included with that kit. Meaning that a motherboard(mini itx) with a on-board processor, RAM, HDD and power supply is sent.
    So the blackTooth will be a all in one kit, excluding any software with the price.

    Click the link to respond:
    I believe I understand USB v Parallel BoB on the Blacktooth but what is "integrated computer" mean?

  • I was wondering what the max depth is for something to go into the 40W C02 Laser cutter and engraver with blacktooth

    Hello, I was wondering if the Blactooth laser cutter can engrave in 3d, different depths in the same piece of wood?

    Additional Information:

    Click the link to respond:
    I was wondering what the max depth is for something to go into the 40W C02 Laser cutter and engraver with blacktooth

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.