[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 617

Question: HOW CAN YOU ENHANCE THE BLACKTOOTH LASER CUTTER?

Current Solution

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Respond:

Other Possible Solutions to this Question

  • how can I exhaust the blacktooth co2 laser cutter

    Exhausting the blackTooth laser cutter is a very important consideration and should be taken seriously, especially if you are cutting materials that give off toxic fumes when the material is burned. You will want a 4 inch hose to connect from the blackTooth to a blower, and another 4 inch hose to connect from the blower to the outside. The blower should be sufficient to provide completely negative pressure within the laser enclosure so there will be no escape of gasses.

    The connections at the machine, at the blower and at the location the hose exhausts outside should be thoroughly checked for leaks. Use a gasket, or silicone. Once complete, try cutting a non-toxic material that will give off an odor (wood, or non-toxic plastic) and try the system and determine if the smell is present.

    Click the link to respond:
    how can I exhaust the blacktooth co2 laser cutter

  • Does the blackTooth laser cutter can acrylic plastic?

    Exhausting the blackTooth laser cutter is a very important consideration and should be taken seriously, especially if you are cutting materials that give off toxic fumes when the material is burned. You will want a 4 inch hose to connect from the blackTooth to a blower, and another 4 inch hose to connect from the blower to the outside. The blower should be sufficient to provide completely negative pressure within the laser enclosure so there will be no escape of gasses.

    The connections at the machine, at the blower and at the location the hose exhausts outside should be thoroughly checked for leaks. Use a gasket, or silicone. Once complete, try cutting a non-toxic material that will give off an odor (wood, or non-toxic plastic) and try the system and determine if the smell is present.

    Click the link to respond:
    Does the blackTooth laser cutter can acrylic plastic?

  • What file types can the blackTooth Laser Cutter accept?

    LaserCAD and the Anywells Laser Controller used in our BlackTooth and Vertical Laser XL laser cutters and engravers can accept these file types:

    .nc (Gcode)
    .ai (Adobe Illustrator)
    .svg
    .pdf (Adobe Acrobat)
    .dxf (AutoCAD and Drawing Exchange)
    .plt
    .dst
    .dsb
    .uds (UD)
    .bmp (Bitmap image)
    .gif (Image)
    .jpg (Joint Photographers)
    .png

    Click the link to respond:
    What file types can the blackTooth Laser Cutter accept?

  • HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

    The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

    Click the link to respond:
    HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

  • HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

    The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

    Click the link to respond:
    HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

  • WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

    If you take the standard parallel cable BoB (Break Out Board), then you will need control software (Mach 3 or EMC2) and CAM software to make your G-Code (such as CamBam). Personally I use CamBam and Mach 3, they work beautifully but don't expect to turn them on and know how they work out of the box. Give yourself a few weeks to get familiar with the basics. CamBam is VERY powerful software for it's price. I'm surprised how much I keep learning on what I can do with it...I highly recommend it if you want as much control as possible.

    Mach 3 + CamBam as a bundle costs $310. EMC2 will give you a free replacement for Mach 3 and is exclusively for Linux.

    If you use the USB BoB, it will cost an extra $75 + $75 for the software. This is an all-in-one package so no need for Mach 3 or CamBam.

    For etching rasters (jpeg, bmp, tiff, non-vectors, photos), I highly recommend PicEngrave. It has been a labor of love for the past 9 years and John has done a wonderful job with it. It easily compares in quality compared to software that is in the $200-$300 range. John's software runs $40 and can be found here: http://picengrave.com/ (don't let the modest website fool you, this stuff can do amazing things). DotG and the Mach3 engrave plugin are two other options and instructions can be found on Dustans page in the gallery on buildyourcnc.com website.

    Click the link to respond:
    WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

  • WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

    I would say mechanically, between the official build instructions, Warren's awesome blog (http://blacktoothlaser.blogspot.com/) and the tips in the forum, the blackTooth is a really simple build. The challenges come with electronics and software. There's a number of different ways to drive the laser and motors. A decent understanding of electronics and computers is a must.

    Click the link to respond:
    WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

  • How long does it take to build the blackTooth Laser Cutter?

    The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

    Click the link to respond:
    How long does it take to build the blackTooth Laser Cutter?

  • how long would it take to build the blacktooth laser cutter?

    The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

    Click the link to respond:
    how long would it take to build the blacktooth laser cutter?

  • How much is your ; blackTooth Laser Cutter and Engraver CO2 40W

    You can find all of the information including the price on the blackTooth Laser cutter and engraver page found here: https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx

    Click the link to respond:
    How much is your ; blackTooth Laser Cutter and Engraver CO2 40W

  • WHAT CAN ADD TO MY BLACKTOOTH LASER CUTTER MEASURE THE TIME OF USE?

    Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

    Click the link to respond:
    WHAT CAN ADD TO MY BLACKTOOTH LASER CUTTER MEASURE THE TIME OF USE?

  • WHAT ARE SOME USEFUL MODIFICATIONS CAN APPLY TO THE BLACKTOOTH LASER CUTTER?

    Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

    Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

    Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

    Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

    Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

    To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

    A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

    Click the link to respond:
    WHAT ARE SOME USEFUL MODIFICATIONS CAN APPLY TO THE BLACKTOOTH LASER CUTTER?

  • HOW CAN ENHANCE THE BLACKTOOTH?

    Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

    Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

    Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

    Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

    Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

    To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

    A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

    Click the link to respond:
    HOW CAN ENHANCE THE BLACKTOOTH?

  • Does the blacktooth laser cutter have a 'trace' ability or 'air cut' where you can visually see the proposed cuts to be made..i.e. visible laser?

    The blackTooth does not come with a beam combiner that allows a visible laser to be combined with the CO2 laser.

    Click the link to respond:
    Does the blacktooth laser cutter have a 'trace' ability or 'air cut' where you can visually see the proposed cuts to be made..i.e. visible laser?

  • Can we order a preassembled version of the blacktooth laser cutter and what would the lead time be.

    We do have the option of assembled blackTooth CNC.
    For further information on lead time and quote; please email (customerservice@buildyourcnc.com)

    Click the link to respond:
    Can we order a preassembled version of the blacktooth laser cutter and what would the lead time be.

  • How to wire the Laser Power Supply with an arduino & GRBL ? (I'm not using a blacktooth laser cutter)

    There is a th or tl on the laser power supply that serves as the trigger on a high or low signal. There is also a potentiometer "in" terminal that will accept a variable signal from 0v to 5v to control intensity. You can use either of these features to fire the laser tube.

    If you have gotten grbl to work, then, no doubtedly, you have the expertise to know the output features of grbl. If grbl allows a pwm output, you can tie this to the potentiometer terminal on the power supply. Otherwise, you will need to use a digital output to control the power supply using th or tl.

    Additional Information:

    Click the link to respond:
    How to wire the Laser Power Supply with an arduino & GRBL ? (I'm not using a blacktooth laser cutter)

  • Where are the wiring diagrams for the blackTooth laser cutter?

    You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

    Additional Information:
    wire size

    Click the link to respond:
    Where are the wiring diagrams for the blackTooth laser cutter?

  • Is the blackTooth Laser Cutter available for custom size orders?

    We will generally consider a change in dimensions or machine features if the change will be beneficial to other users as well. This is due, in part, to the time it takes to make such changes and that it maintains the desired functionality and expected safety.

    What dimensional changes do you wish for the blackTooth?

    Additional Information:
    I was hopping to be able to have a cutting surface of 2' x 4'

    Additional Information:
    We have that size in our queue to be designed. However, you may be more interested in the laser adapter we are designing for the existing CNC machines to house a laser tube on the z-axis of these machines. This will be a quicker turnaround.

    Additional Information:
    Is there a time frame possibly to having this adapter made as well as cost? I am possibly looking to start a business so I am looking for something I can use to mass produce some specific parts.

    Additional Information:
    There is one project that takes precedence to the adapter, so I would expect in two months time.

    Click the link to respond:
    Is the blackTooth Laser Cutter available for custom size orders?

  • I am looking at buying the blacktooth-laser-cutter-engraver-40w. Can you give me some idea of the types and thickness of material this machine will cut and/or ingrave?

    Considering that "materials being lased by may emit gasses that are harmful to humans (corrode human tissue and cause damage to respiratory organs). Always read the MSDS (Material Safety Data Sheet) for the material to be lased. You can find these MSDS from manufacturer websites for the material you are considering for use in the laser system."
    We successfully have worked on Thin sheets of Brasswood, glass, foam, plexi-glass. The thickest materials you will be able to successfully cut is 1/4".

    Click the link to respond:
    I am looking at buying the blacktooth-laser-cutter-engraver-40w. Can you give me some idea of the types and thickness of material this machine will cut and/or ingrave?