[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 637

Question: WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

Current Solution

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Respond:

Other Possible Solutions to this Question

  • WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

    The blackfoot requires a total of 50 feet of cable.

    The X axis needs 15 feet
    The Y axis needs 17 feet
    and the Z-axis needs 18 feet

    These are 20 gauge 4 conductor cable.

    Click the link to respond:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • HOW LONG SHOULD THE MOTOR CABLES BE FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    HOW LONG SHOULD THE MOTOR CABLES BE FOR BLACKTOE

  • WHAT LENGTH OF MOTOR CABLE SHOULD BE USED WTIH THE BLUECHICK V4.2

    The recommended total length of motor cable should be 15 feet for the blueChick v4.2

    Z - 6 feet
    Y - 5 feet
    X- 4 feet

    20 AWG 4 conductor

    If your drivers will be positioned farther from the machine, you may need longer cable.

    Click the link to respond:
    WHAT LENGTH OF MOTOR CABLE SHOULD BE USED WTIH THE BLUECHICK V4.2

  • What wire gauge should be used for the 36V 8.8 amp power supply

    Most of our power supplies allow for a 9 amp current draw.

    For the Neutral, Live and earth ground, wire gauge for that level of current is 14 for relatively short cable lengths. Increase the gauge for longer lengths past 25 feet.

    For the DC 24V output terminals to the drivers, 20 gauge is fine. If the power supply is connecting to only one driver, increase the wire gauge to 14.

    Additional Information:
    What gage wire should I use from motor to driver

    Click the link to respond:
    What wire gauge should be used for the 36V 8.8 amp power supply

  • What profile do I use in VCarve for a BlackToe?

    The blackToe is a CNC Router based on standard CNC Routing and milling actions. If you are referring to a profile machining operation (where the path follows the inside or outside edge of a polygon, line, arc or circle) then the profile is actually more a function what you want the CNC router (blackToe in this case) to do. A profile expects a specific end mill in the spindle and requires the specifications of the end mill in the profile operation.

    If you are referring to profile to mean "post processor" or specifications (profile of the control) for the g-code interpretation for a specific control program (like Mach3), then you will need to set the post processor in VCarve post-processor to the control program you are using.

    Please provide more specific information here so I can delve in a bit deeper.

    Click the link to respond:
    What profile do I use in VCarve for a BlackToe?

  • WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

    You can expect a one week lead time for our machines.

    Click the link to respond:
    WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

  • What thermocouple or thermister should I use for the extruder hot end?

    The best choice would be a type K thermocouple.

    Click the link to respond:
    What thermocouple or thermister should I use for the extruder hot end?

  • WHAT IS THE LEAD TIME FOR BLACKTOE?

    You can expect a one week lead time for our machines.

    Click the link to respond:
    WHAT IS THE LEAD TIME FOR BLACKTOE?

  • WHAT IS THE LEAD TIME FOR BLACKTOE?

    You can expect a two week lead time for the redFrog pick and place machine.

    Click the link to respond:
    WHAT IS THE LEAD TIME FOR BLACKTOE?

  • WHAT LEAD TIME CAN EXPECT FOR BLACKTOE SO PICK UP THE MACHINE?

    You can expect a one week lead time for our machines.

    Click the link to respond:
    WHAT LEAD TIME CAN EXPECT FOR BLACKTOE SO PICK UP THE MACHINE?

  • CABLE LENGTHS FOR THE BLACKFOOT

    The blackfoot requires a total of 50 feet of cable.

    The X axis needs 15 feet
    The Y axis needs 17 feet
    and the Z-axis needs 18 feet

    These are 20 gauge 4 conductor cable.

    Click the link to respond:
    CABLE LENGTHS FOR THE BLACKFOOT

  • what depth increment should I use for pocketing and profiling with the 1/2" end mill?

    The pocketing depth per pass will depend on the hardness of the material, the router/spindle you are using and on the melting point of the material. Use the feedrate that you would normally use for the size and type of end mill. You will need to test the depth per pass, starting at the full depth of the pocket. The spindle should have no problem, but if you are using a router, then it may bog down, so easing up on the depth per pass is recommended. If the spindle/router has no problem at the depths you are using, then you need to evaluate the edge finish to determine if it is acceptable. If it is not acceptable, then ease up on the depth per pass. Keep doing these steps until you have the finish and precision you expect.

    Click the link to respond:
    what depth increment should I use for pocketing and profiling with the 1/2" end mill?

  • HOW MUCH MOTOR CABLE SHOULD PURCHASE FOR THE BLUECHICK

    The recommended total length of motor cable should be 15 feet for the blueChick v4.2

    Z - 6 feet
    Y - 5 feet
    X- 4 feet

    20 AWG 4 conductor

    If your drivers will be positioned farther from the machine, you may need longer cable.

    Click the link to respond:
    HOW MUCH MOTOR CABLE SHOULD PURCHASE FOR THE BLUECHICK

  • THE BLACKTOE REQUIRES HOW MUCH MOTOR CABLE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    THE BLACKTOE REQUIRES HOW MUCH MOTOR CABLE

  • What wiring should I use to connect two motors for one axis?

    Yes, you can use 2 motors in the same axis output, however you will still need a driver for that motor! Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

    Also you can run a slave motor using another axis on the board, and setting it up in the Planet-CNC settings.

    Planet-CNC/File/Settings/Axes, here you will enter 3 in the Number of Axes location, and then change the Function of the Axis 4 to Slave 1. There you will have the 4th axis or A-axis be a slave for the x-axis.
    Slave 1 - X-Axis
    Slave 2 - Y-Axis
    Slave 3 - A-Axis
    Slave 4 - B-Axis
    Etc...

    Click the link to respond:
    What wiring should I use to connect two motors for one axis?

  • What should the "glue groove" width be for flexible strip brush?

    The width and height that we have on our brush piece for our cnc machines, is 1/4" width and .30" depth , the length is dependent on your specific dimension of brush and the design of the brush piece.

    Click the link to respond:
    What should the "glue groove" width be for flexible strip brush?