PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
WHAT NOT INCLUDED WITH THE MACHINE?

Nema 23 stepping motors with 100 oz-in rated holding torque and 1/4" shaft.

Click the link to add information to this solution:
WHAT MOTORS DOES THE BLACK TOOTH USE?

Nema 23 stepping motors with 100 oz-in rated holding torque and 1/4" shaft.

Click the link to add information to this solution:
WHAT MOTORS DOES THE BLACK TOOTH USE?

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE SHIPPING COST OF MACHINE TO AUSTRALIA?

An axis is a direction of motion controlled by the CNC machine control. It can be linear (motion along a straight line) or circular (a rotary motion). The number of axes a machine has determines it's machining capabilities. A 2.5 axis machine really has three moving axes, but only two axes can move together (most machines sold today are full three axis machines). For machining centers, a three axis machine will have three linear axes. A four or five axis machine will have three linear axes as well as one or two rotary axes.

Note that 2.5 versus 3 axis has yet another context. 2.5 axis machining requires that the machine have three axes, but only two axes must be moving simultaneously at any one time. (Simple operations, like drilling and most milling, fall into this category). On the other hand 3-axis machining requires that all three axes be moving at the same time (More complex operations, like the machining of sculptured surfaces required in molds and airfoils, fall into this category.)

Additional Information:


Additional Information:

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE IN A 2.5 AXIS MACHINE?

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE SHIPPING COST TO MY COUNTRY?

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE SHIPPING FEE TO MY COUNTRY?

Yes, we do that with our machines. You can use the rail blocks to serve as the alignment mechanism. If you have a slight misalignment, the block will not pass that joint. Make sure you use the same rail from the same supplier.

Click the link to add information to this solution:
Hi i'm looking to upgrade my rail system along my X-axis which is 10 ft. Im wondering what it takes or if it is even possible to join two HIWIN guidways together to make up the 10' run.

The formula and calculation is a starting point to get into the area of steps per inch. You will then need to use the mach3 calibration utility to get the exact steps per inch.

Formula:
step per inch = (motor steps * microstepping) / (travel at one turn of the motor in inches)
if microstepping is set at 16 (1/16 on the driver) then and you are using a sprocket and chain with a pitch of .25 inches and 12 teeth on the drive sprocket
= (200 * 16) / (12 * .25)
= 3200 / 3
= 1066.666 steps per inch

For lead screw that has a travel of .5 inches at one turn like the 5 start 1/2 inch lead screw and using 4 microsteps per step (1/4):
= (200 * 4) / (.5)
= 800 / .5
= 1600 steps per inch

Remember to use the mach3 calibration wizard and double check the driver microstep setting.

Additional Information:


Additional Information:


Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
SrCyFFpZ

Additional Information:
-1 OR 2+902-902-1=0+0+0+1 --

Additional Information:
-1 OR 2+722-722-1=0+0+0+1

Additional Information:
-1' OR 2+275-275-1=0+0+0+1 --

Additional Information:
-1' OR 2+345-345-1=0+0+0+1 or '6eaEcsTN'='

Additional Information:
-1" OR 2+474-474-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@E5bKt

Additional Information:
1'"

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT IS THE FORMULA TO DETERMINE STEPS PER INCH OR RESOLUTION FOR EACH AXIS?

Does your breakout board (interface) have a relay? If so, you can connect one of the router/spindle's ac lines through the relay. The M3, M4 and M5 codes are used to control the router/spindle. Typically, the M codes are automatically added to the g-code regardless if you configure this in your CAM software. If you have the breakout board from buildyourcnc, you can go to the product page for the breakout board and the relay connection diagram and narrative is in the instructions on that page.

Click the link to add information to this solution:
WHAT IS THE MOST EASY WAY TO HOOK UP MILL IN THAT AUTOMATICALLY STARTS WHEN CYCLE STARTS, AND STOPS GCODE THROUGH?

Yes, we have fully assembled machines that come complete with the spindle (and laser if needed) with sizes ranging from 1'x2' all the way up to 6'x12' or longer. We can also make custom fully assembled machines with other sizes. All of these machines are perfect for very intricate detailed work including but definitely not limited to sign making, bas relief, cabinetry, architectural model making, engraving, machine parts, automotive, custom sound enclosures (automotive or other), and other scientific application which we have delivered machine for many types of these applications.

Our machines are as follows (in order by size, larger at top):

The Fabricator Pro (although stated on the website at 4'x8') can be provided up to a 6'x12' (or longer) size. Call us for the price above the 4'x8' size.
https://www.buildyourcnc.com/item/cnc-machine-fabricator-pro-milling

The greenBull 4x, 5x or 6x CNC Machine is available fully assembled; however, you are responsible for building the table on this machine, but the price is considerably lower. The 4x, 5x, and 6x is a width specification and the length is determined by your table length.
4x: https://www.buildyourcnc.com/item/cnc-machine-greenBull-v4-4X-milling-hybrid
5x: https://www.buildyourcnc.com/item/cnc-machine-greenBull-v4-5X-milling-hybrid
6x: https://www.buildyourcnc.com/item/cnc-machine-greenBull-v4-6X-milling-hybrid

The 4'x8' greenLean CNC Router (Table bed is vertically oriented with a slant) fully assembled:
This machine is fully assembled with the overall frame. The customer would need to fasten the frame to the wall and affix a spoilboard to the bed.
https://www.buildyourcnc.com/item/cnc-machine-greenLean-v1-milling

The 4'x8' Vertical Laser XL Laser Cutter and Engraver fully assembled:
https://www.buildyourcnc.com/item/cnc-machine-vertical-laser-xl-laser-cutter

The 4'x8' blackFoot CNC Router:
This machine requires a table to be built by the customer.
https://www.buildyourcnc.com/item/cnc-machine-blackFoot-v4-milling

The 2'x4' blackToe CNC router fully assembled complete with table:
https://www.buildyourcnc.com/item/cnc-machine-blacktoe-v4-2x4-milling

The blueChick CNC Router fully assembled completel with table:
https://www.buildyourcnc.com/item/cnc-machine-bluechick-v4-milling

Click the link to add information to this solution:
WHAT IS THE PRICE OF ASSEMBLED MACHINES COMPLETE?

Yes, we have fully assembled machines that come complete with the spindle (and laser if needed) with sizes ranging from 1'x2' all the way up to 6'x12' or longer. We can also make custom fully assembled machines with other sizes. All of these machines are perfect for very intricate detailed work including but definitely not limited to sign making, bas relief, cabinetry, architectural model making, engraving, machine parts, automotive, custom sound enclosures (automotive or other), and other scientific application which we have delivered machine for many types of these applications.

Our machines are as follows (in order by size, larger at top):

The Fabricator Pro (although stated on the website at 4'x8') can be provided up to a 6'x12' (or longer) size. Call us for the price above the 4'x8' size.
https://www.buildyourcnc.com/item/cnc-machine-fabricator-pro-milling

The greenBull 4x, 5x or 6x CNC Machine is available fully assembled; however, you are responsible for building the table on this machine, but the price is considerably lower. The 4x, 5x, and 6x is a width specification and the length is determined by your table length.
4x: https://www.buildyourcnc.com/item/cnc-machine-greenBull-v4-4X-milling-hybrid
5x: https://www.buildyourcnc.com/item/cnc-machine-greenBull-v4-5X-milling-hybrid
6x: https://www.buildyourcnc.com/item/cnc-machine-greenBull-v4-6X-milling-hybrid

The 4'x8' greenLean CNC Router (Table bed is vertically oriented with a slant) fully assembled:
This machine is fully assembled with the overall frame. The customer would need to fasten the frame to the wall and affix a spoilboard to the bed.
https://www.buildyourcnc.com/item/cnc-machine-greenLean-v1-milling

The 4'x8' Vertical Laser XL Laser Cutter and Engraver fully assembled:
https://www.buildyourcnc.com/item/cnc-machine-vertical-laser-xl-laser-cutter

The 4'x8' blackFoot CNC Router:
This machine requires a table to be built by the customer.
https://www.buildyourcnc.com/item/cnc-machine-blackFoot-v4-milling

The 2'x4' blackToe CNC router fully assembled complete with table:
https://www.buildyourcnc.com/item/cnc-machine-blacktoe-v4-2x4-milling

The blueChick CNC Router fully assembled completel with table:
https://www.buildyourcnc.com/item/cnc-machine-bluechick-v4-milling

Click the link to add information to this solution:
WHAT IS THE PRICE OF ASSEMBLED MACHINES COMPLETE?

The password is: 608

Click the link to add information to this solution:
WHAT IS THE SYSTEM PASSWORD FOR LASER CONTROL UNIT?

If one of your stepper motors decides to stop moving and the others are moving during a CNC milling or laser cutting job, then there could be two things that could be causing this.

- The motor found its limiting torque (usually comes with a not-so-pleasant sound). This is where the control software is trying to move the stepper motor too fast (velocity, or too fast too quickly, acceleration) and the load against the stepper motor (inertia of the machine, or the material against the end mill while milling). Recommended action is to lower the velocity and/or acceleration, and/or lower the feedrate when cutting.

- There is a wiring issue with the wiring from the driver to the motor. This could be a loose wire, or a chafed wire (or two shorting together). It can also be a loose digital wire from the controller board to the driver. Sometimes wire ties can be the culprit. Recommended action would be to thoroughly inspect the wiring.

It's probably not the limit switches since that would cause a stop to the entire motion of the cnc router or laser machine.

Sometimes Mach3 will show a status when something goes wrong, but in cases where the motor is stopping due to its torque limit, then that would not be shown in the status. It's always good to check it anyway.

Additional Information:
I need to clarify my situation a little better after going to my shop and trying to run another program on Mach 3. About 15 minutes into the milling process all the motors (2-X axis, Y axis and Z axis)stop but the program continues to run. I stop the program and after a couple of minutes when I try to restart the program all the motors start working again. Then after another 15 minutes or so, all the motors stop again. I checked and rechecked my wiring. This has never happened to me before when running the same programs with the same setups and motor speeds. All of a sudden when I reloaded a program I successfully used before it does this. Do you have any recommendations?

Additional Information:
Yeah, it sounds like a more complex issue. Have you tried running in the air without using the spindle. This may be a power related issue.

Additional Information:
That's exactly what I did. I ran the program without the router motor on just to see if the motors would get through the whole program but they stopped working after about fifteen minutes and then I was able to start them again after about 3 or 4 minutes. I never had this problem before so you can imagine my frustration especially after ruining a couple of projects on expensive material.

Additional Information:
Sure. I can completely understand. Try this: disconnect all but one of the driver from power and digital connection and do the air run. Repeat this for each driver and note your findings. This will rule out the drivers causing a power failure.

Also, is your stepper motors and drivers on a separate power circuit from the computer?

Additional Information:
I will try disconnecting each driver and digital connection, which will be a real pain because it will be hard to access.

All the stepper motors, drivers and computer are plugged into the same power strip.

Additional Information:
Ok, so there is no power failure going on, but I believe it is necessary to test each stepper motor and driver pair individually. Hopefully that will lead to a conclusion.

Additional Information:
It will take a little time but I will do it and report back on my findings.

Additional Information:
Curious, what machine is exhibiting this problem?

Additional Information:
I purchased a BYCNC kit back in 2009 with an approximate cutting area of 2' X 4'. I later changed out the Z-Axis Motor and controller for a larger one and have two X-axis motors and controllers. In 2010 I rebuilt the machine out of birch plywood instead of the particle board that the kit supplied. I sent Patrick pictures to him. The machine never gave me a problem till now.

Additional Information:
Thanks for the update. This is Patrick by the way. I answer pretty much all of the Customer Service questions. That machine has given quite a good history.

Additional Information:
I love the machine and made a number of samples of my work for my e-commerce site, but I can't start selling product until I know this problem is solved because I will not be able to fulfill orders. I finally got all the electronics out of its enclosed protected area near the machine so that I test each controller as you recommended. I hope the problem can be rectified. Will let you know.

Additional Information:
Thanks.

Additional Information:
I tested each stepper motor and driver pair individually and they worked so what might be the next step?

Additional Information:
Did each stepper motor driver pair work for the full +15 minutes?

Additional Information:
Yes, I had them in operation for over 30 minutes.

Additional Information:
Ok, well it’s good that the motors and driver are ok. We are now down to the power supply and the breakout board as possible causes for the stop. I have a feeling it may be the power supply where with all three drivers drawing current and the power supply maybe getting too hot. Is the fan in the power supply working? You can also test to see if there is 36 volts on the power supply voltage output (V+ and V-).

Regarding the breakout board, if you have an oscilloscope, you can test if the driver pulses are outputting, but I would consider this as a last resort after you determine if there is a problem with the power supply.

Additional Information:
I tested the power supply with a voltmeter and each output was registering 39-40 volts. I think the problem may be the g-code. I am using V-Carve pro to do design and output to Mach 3 Mill g-code. When I studied the g-code lines I noticed that further into the program the z-axis g-code stopped zeroing out to move to the next part of the carving. In other words both the x and y keep moving and the z just stopped working because there was g-code missing. I think something is missing when the design was converted to g-code. I noticed that when I ran a simpler project it worked without problems so I need to investigate this further.

Additional Information:
New Update, Its not the g-code. I started to run the long program and everything was working fine until about 45 minutes into it, all the motors stopped working (but the program was still running) and there was a high pitched hum. When I put my hands on the motors they were all trying to move but it seemed they were all stalled. I turned the power off, gave it a minute and when I turned it back on I was able to move the motors again. Could this be a power supply problem?

Additional Information:
It does sound more and more like a power supply problem. Did you test the power supply after the motors stopped?

Additional Information:
No, I did not. What should I be looking for.

Additional Information:
It’s good that you know the voltage during normal operation, so you have a base understood. If the power supply is the problem, the voltage will be reduced or non existent when measured after the problem.

Additional Information:
Also, check to see if the fan is running on the power supply when the motors stop. That may (not absolutely) be an indication.

Additional Information:
I'll run another test, check the voltage and fan when the problem occurs and let you know. Thanks for hanging in there with me as we try to resolve the problem.

Additional Information:
It’s my pleasure. This service is rarely used and is faster then email. Odd nobody uses it. Any recommendations you can give would be great. No problem using this FAQ to pose ideas as this resolution will be cleaned up later.

Additional Information:
It might be that people do not realize you can communicate through the sight like this because they are so used to e-mail and texting. You may want to explain this feature in the customer service section.

I ran the program this morning and it did not take long before the motors stopped. While operating the voltages for all three motors was 46 volts, when the motors stalled (and again there was a high pitch hum) the voltage went up to 60 volts and the fan on the power supply was operating.

Additional Information:
So, the driver work individually, but not all together. There is a high pitch sound when the motors fail. You have noted 60 volts from the power supply and the supply fan remains on. This is a difficult issue to resolve, but it seems to me that your power supply may be bad. The 60v measurement tells me that the current dropped and ohms law tells us that is current drops, volts will rise if the resistance stays the same.

Additional Information:
As one last test I am going to test each driver again and let them go through the entire program because it seems that the failure can occur at the beginning or towards the end of the program. When I originally tested ach driver I let them run for about a half an hour and the program takes over an hour to run completely. I just want to make sure that it is not the drivers. I will report back when I finished but as you noted it may be the power supply but I want to make sure.

Additional Information:
That’s a great idea.

Additional Information:
I just ran the x-axis through the whole program and there was no problem especially since I have two NEMA 23 motors moving that axis. Before I check the Y and Z could having a NEMA 34 on the Z axis with appropriate controller be a problem. I used the larger motor on the z axis because the router I am using is a large 1 1/2 hp. I've run this program in the past with this set-up and have not had a problem.

Additional Information:
Having a, say 3.0 amp driver, driving a stepper motor that typically requires a 6 amp driver would not seem to be an issue since the driver is limiting the current draw, but the driver may not be able to handle larger coil and back EMF with the protection on the 3.0 amp driver. With that said, I don’t believe that is the issue in this case.

Additional Information:
I don't either because I was able to run this and other complicated programs with this set-up in the past. I will let you know on the y and z axis.

Additional Information:
Thanks

Additional Information:
I ran the Y axis and z axis separately through the entire program and there was no stopping or problem. I guess the culprit is the power supply and I'll order a new one and hope that resolves the problem.

Additional Information:
Yes, that is the most probable cause. Please keep me informed. Thanks!

Additional Information:
Received and installed the new power supply. I ran the program with the router on and it worked flawlessly. The program runs for an hour and a half and I did not have a single problem. I guess it was the power supply but I was glad to go through all the diagnostics we discussed before replacing it. I hope this power supply lasts a lot longer than the last one. Thanks much for hanging in there with me and coming up with the solution.

Additional Information:
It’s my absolute pleasure and I am so happy to hear that the power supply replacement solved the problem.

Additional Information:


Additional Information:
Y axis stop working X & Z work fine Y axis has two motors have check wiring & connections new breakout board still the same port & Pin set OK dont no were to go next David

Additional Information:


Additional Information:
my cnc plasma cutter will run out the program when cutting. what is the cause?

Additional Information:
The cnc plasma question shod be a separate question. Can you pise that question by clicking the customer service live menu button at the top? Thanks.

Click the link to add information to this solution:
WHAT CAUSES ONE OF MY TWO AXIS MOTORS TO STOP WHILE THE MACH3 PROGRAM IS STILL RUNNING

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

Additional Information:

Click the link to add information to this solution:
WHAT WOULD BE THE COST OF FREIGHT TO SOUTH AUSTRALIA?

Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
Number of Planners 1 1 1
Number of Axis 6 6 6
Out of Band Axis (OBA) 0 1 6
Slave axis (uses up coordinated axes) 3 N/A N/A
Slave motors (does not use up coordinated axes) N/A 4 per Axis 4 per Axis
API Interface - Open to All Hardware Yes Yes Yes
Extended Plugin Support Yes Yes Yes
User customizable GUI Yes Yes Yes
Unified (GUI) Interface - PLC, CNC, etc.. Yes Yes
Unlimited IO Yes Yes Yes
Modbus PLC Yes Yes Yes
PMC (Ladder Logic addressing for cnc/plc) Yes Yes
Unlimited File Size Yes Yes
Tool Path Display Yes Yes Yes
Tool Path Speed & Quality Low High High
Scripting - Customization Yes Yes Yes
LUA Scripting - simple, fast, cross-platform Yes Yes
- Lua sockets (ftp, http, smtp,..) Yes Yes
- SSL (security layer) Yes Yes
- LFS (manage large files and data storage) Yes Yes
- Seriel port Yes Yes
- Enraving of part numbers / serial numbering of parts Yes Yes
- Plugin panel objects Yes Yes
IPC Library for Data Sharing/tracking (Interprocess communication) Yes Yes
Full Feature Screens/Controls Per Machine Type Yes Yes
Currently Availabe: Mill, Router, Lathe, 3d Printer Yes Yes
Multiple gcode Interpruters (Per Machine Type) Yes Yes
Probing - Intergrated in standard screens Yes Yes
Simulated 3d Machining (with additional plugin license) Yes Yes
Tool Life Management (G10 L3 command) Yes
Screw Mapping Yes
Professional Screen Designer (advanced G.U.I.) Yes
- Screen Animation Control Yes
- Screen Integrated Tool Table Control Yes
- Screen Integrated Work Offset Control Yes
- Screen Integrated gcode editor Yes
- Screen Artsoft Wizard Package Integration Yes
Macro B gcode Programming (#variables) Yes
- User definable gcodes via marco calls Yes
- Macro Calls: G65, G66, G66.1 Yes
- gcode via marco call (custom G codes via macro B) Yes
- mcode via macro call (custom M codes via macro B) Yes
- mcode via sub code (custom M code via sup program) Yes
- Conditional gcodes Yes
- set VN call - define variable names Yes
gcode Editor Included Yes
Scripted M code (custom M code via LUA script) Yes Yes
Variable Speed Spindle Yes Yes Yes
Spindle Relay Yes Yes Yes
Coolant relay Yes Yes Yes
Mist Relay Yes Yes Yes
Threading Yes Yes Yes
Rigid Tapping Yes Yes Yes
Single Block Yes Yes Yes
Block Delete Yes Yes Yes
Optional Stop Yes Yes Yes
MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
Cutter Comp Yes Yes Yes
Fanuc Type C Cutter Comp Yes Yes
Fixture Offsets Yes Yes Yes
G51 Scaling Yes Yes Yes
G92 Offsets Yes Yes Yes
G52 Offsets Yes Yes Yes
Event Driven Yes Yes
Multi Line MDI Yes Yes
Subs In MDI Yes Yes
OpenGL Optimization Yes Yes
Multi-platform OS Compatibility Option Yes Yes
Online Support Yes Yes Yes
Phone Support Option Available Yes
Support Priority Yes
Available to End Users as "Do-it-yourself" Yes Yes
Summary - Mach3 versus Mach4 :
Mach4 Hobby is the closest comparable version to Mach3, yet it is still much more advanced. The price point of these versions is nearly
identical. Mach3 is very popular for hobby enthusiest and is used in highly modified form by some great OEM's. In general, Mach4 is more
complex than Mach3 and follows cnc industry standards. Mach3 has many customizations to make it easier for hobby users, but can lead to
difficulties if users plan to apply their knowledge to more advanced systems. Mach4 is built as a full featured cnc controller capable of high
speed machining for servo and stepper systems. Mach3's feature set is complete, while Mach4's will continue to expand. If you are new to cnc,
Artsoft highly recommends using and learning Mach4 even if it appears that Mach3's feature set will be adequate for your needs.

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN MACH3 AND MACH4?

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

The marathon is the longest running race in the Olympic games.

Additional Information:
marathon

Additional Information:
50 km walk

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
decathlon

Additional Information:
Which group was no.1 in the charts in ?95 with ?back for good??


Additional Information:
Which is the longest running event in the Olympics

Click the link to add information to this solution:
WHAT LONGEST RUNNING RACE IN THE OLYMPIC GAMES CALLED?

Basketball is the most popular indoor sport in the USA

Additional Information:
boxing

Additional Information:
boxing

Additional Information:
boxing

Additional Information:
Basketball


Additional Information:
Basketball


Additional Information:
Which indoor sport is the most popular in the US

Additional Information:
Who recorded A Boy Named Sue

Click the link to add information to this solution:
WHAT THE MOST POPULAR INDOOR SPORT IN U.S.A.?