BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

Here is a link to a tutorial for a DIY relay circuit:

Click the link to add information to this solution:
I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

Yes, you can use lubrication, like 3-in-1 oil to make it a bit easier. You will need to run it up and down to break it in.

Additional Information:

Click the link to add information to this solution:
THE LEAD SCREW IS VERY HARD TO TURN. BACKLASH BUSHING SEEMS BE TOO TIGHT AND BINDING ON SCREW. DO IT NEED LUBRICATION OR DID DAMAGE NUT WHEN INSERTING SCREW?

To get the activation code, all you need to do is plug the USB board into the computer using a USB cable, go to machine -> firmware -> update. After the firmware is updated the program will present to you a dialog box containing the activation code.

Additional Information:
MUAR-QVXU-CAYW-CBWQ


Additional Information:
MUIS-RQPB-PTHB-QTTB

Additional Information:
MUIH-EERP-IADB-TRIP

Additional Information:
9zYWBVf5TxKSK7hEr8gFX3EBw5wa0AMMllQqgftIAnKvZ8DXItLxaPbOB3jWvnpczl/sM/De0scRPHfSxWGmcA==

Additional Information:
Key: LUQR-BQYI-SCEW-QVBT

Additional Information:


Additional Information:
after i copy the code in the lower case i recived the same message (more than 8 times) ,, this is a evaluation...,, what i need to do to register properly?

Additional Information:
MUJR-BISM-KRDN-KKER
056971

Additional Information:
0561234

Additional Information:
MURL-QPQU-EGBJ-FNMB

Additional Information:
MUCE-LFMQ-WBCW-MLHO

Additional Information:


Additional Information:
LUTA-ADVJ-FXTW-FBCE

Additional Information:
LUTA-ADVJ-FXTW-FBCE

Additional Information:
looking for registration key for MUUK-IBTW-ECTL-CJWD

Additional Information:
MUXO-PIYY-KNHD-RKLY

Additional Information:
MUUE-YYCR-FCIC-VATK

Additional Information:
MUUE-YYCR-FCIC-VATK

Additional Information:


Additional Information:
MUEY-YLJU-OBRR-LJBV

Additional Information:
MUSP-JFDV-EKGQ-OVLW

Additional Information:
MUSP-JFDV-EKGQ-OVLW

Additional Information:


Additional Information:


Additional Information:
MULY-XRYF-BBDN-FBWP

Additional Information:


Additional Information:


Additional Information:
how to generate activation code richauto a11

Additional Information:
MUJC-LNIL-EOHS-YKNQ

Additional Information:
sdfd

Additional Information:
m l

Additional Information:
MUXC-RWKB-PKAL-HGNN

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Click the link to add information to this solution:
THEY ARE ASKING FOR THE ACTIVATION CODE AND SERIAL NUMBER USB BOARD. HOW CAN GET THAT INFORMATION?

What 3d printer do you have?

Additional Information:
whiteant

Click the link to add information to this solution:
HAVE 3D PRINTER THAT WANT TO MAKE CNC ROUTER ,IS THERE ANY GUIDES SHOW ME THE WAY

Does your breakout board (interface) have a relay? If so, you can connect one of the router/spindle's ac lines through the relay. The M3, M4 and M5 codes are used to control the router/spindle. Typically, the M codes are automatically added to the g-code regardless if you configure this in your CAM software. If you have the breakout board from buildyourcnc, you can go to the product page for the breakout board and the relay connection diagram and narrative is in the instructions on that page.

Click the link to add information to this solution:
WHAT IS THE MOST EASY WAY TO HOOK UP MILL IN THAT AUTOMATICALLY STARTS WHEN CYCLE STARTS, AND STOPS GCODE THROUGH?

If your Z axis is moving in the opposite direction, go into Mach3, click on config, ports & pins, then click on the motor outputs tab. You will see the axes labeled on the left and the parameters labeled on the top of this dialog box. Toggle the dir low active for the z-axis.

Additional Information:
What if I'm having the same issue on a different axis?

Additional Information:
You can follow the same procedure as with the z-axis. When you get to the motors outputs tab, toggle the dir low active checkbox for the axis that you would like to change.

If you are using another control program, let me know and I will add the recommended action here.

Additional Information:
Girbl

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:

Click the link to add information to this solution:
My Z-axis seems to be reversed on a fully assembled machine... I've tried reversing it in the config settings on Mach 3, but to no avail. What do I need to do? IS this a wiring issue that was not done correctly at the factory?

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

I have not come across this problem, but there may be USB, or firmware issues that you are experiencing. I would recommend going on the polabs website and using their support center (https://support.poscope.com/)and posing that question to them. Also, have you tried the ethernet port as an alternative to see if that helps?

Here is the response from an LLM:

Check USB Cable and Port: Start with the basics. Sometimes this error is due to a poor USB connection. Ensure you're using a high-quality, shielded USB cable and that it's plugged into a USB port directly on your computer, not through a hub. If possible, try a different USB port or a different cable to rule out any issues there.

Update Firmware and Software: Ensure that both your PoKeys57CNC firmware and the Mach4 software are up to date. Firmware updates for your PoKeys board might include optimizations or fixes that address connectivity issues.

USB Polling Rate: This error can also arise from the USB polling rate setting in the PoKeys configuration software. It might be set too high for your system's ability to handle it. Try lowering the polling rate and see if that resolves the error.

Computer Performance: Check your computer’s performance. If it’s running several heavy applications simultaneously, it might not be able to process signals from the PoKeys board fast enough. Try closing unnecessary applications or consider using a dedicated machine if your current setup is too taxed.

Mach 4 and PoKeys Plugin Configuration: Dive into the Mach 4 plugin configuration for PoKeys. Ensure that all settings are correctly configured as per the manual. Incorrect settings might lead to communication bottlenecks.

Connection Quality and Interference: Consider any potential interference sources near your CNC setup or computer. Electromagnetic interference from large motors, other electronics, or long cable runs can affect communication quality. Try rearranging your setup to minimize interference.

Consult Documentation and Support: If the issue persists, consult the detailed documentation provided by PoKeys or reach out to their customer support. They can offer more specific advice based on the latest product updates or known issues.

Click the link to add information to this solution:
I HAVE FOLLOWED YOUR YOUTUBE VIDEO ON SETTING UP THE POKEYS 57CNC BOARD BUT WHEN OPEN MACH 4 GET A ERROR MESSAGE CONNECTION IS TO SLOW

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

Additional Information:

Click the link to add information to this solution:
THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

BYCNC Response:
The book build was intended to be 20 inches x 40 inches. Larger machines were designed after the book build was introduced so customers would have the option to go bigger than what the book offered. Check out our larger machines on the website as the machines sizes range from 1 foot x 3 feet all the way up to 6 feet x 12+ feet.

User Response:
I'm not wanting to spend $3,000+ on a machine, I want to build one that will do a 4x8 sheet of wood. Will the plans in the book scale up?

BYCNC Response:
It is possible to scale the book build up, but the rigidity of the gantry would be questionable at that span, even if the height of the gantry structure were to be increased. The gantry design would need to be modified to become a box shape rather than a flat configuration. The kits on the site were design for those wanting a larger machine.

Click the link to add information to this solution:
I BOUGHT YOUR BOOK AND WAS HOPEING IT HAD PLANS OR DIMENTIONS ON HOW TO BUILD A CNC HOLD 4X8 SHEET OF PLY. WILL THE IN SCALE UP?

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

Although the strains may sometimes be the same as in the previous year's vaccine, you should NOT use the previous season's vaccine you might still have in your refrigerator. Influenza vaccine distributed in the northern hemisphere expires on June 30 after each season; expired vaccine should NEVER be administered. Secondly, antibody titers that persons might have achieved from the previous year's vaccination will have waned and need to be boosted with a dose of the current year's vaccine.

Click the link to add information to this solution:
WHY DO PEOPLE RECEIVED INFLUENZA VACCINE LAST YEAR STILL NEED TO GET VACCINATED THIS WHEN THE VIRUSES HAVEN'T CHANGED?

The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:

Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I HAVE A 2000 WK 11–3 Z LIMIT SWITCHES GOING TO C10R10 BREAKOUT BOARD . CAN ALSO USE THEM AS MY HOME POSITION WELL. NEED THE WIRING CONFIGURATION

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
IT POSSIBLE TO BUY THE CAD FILES FOR BLACK FOOT MACHINE, MECHANICAL PARTS AND ELECTRONICS BUT NOT WOODEN PARTS, SAVE SHIPPING COSTS? IN THAT CASE I WOULD INSTRUCT SOMEONE MILL ME.

You should use the linuxcnc.org site and click on the download menu item. They have an EU mirror as the main download option.

Click the link to add information to this solution:
AM STRUGGLING TO DOWNLOAD THE LINUX EMC2 FREEWARE. MY GET INTERRUPTED AT LAST MINUTE. IS THERE ANOTHER WAY OR PLACE WHERE COULD MAYBE TRY IT FROM?

This will depend on the VFD you have to identify the correct terminal. The terminal on the VFD will be labeled AI1 typically (Analog Input #1). You will also need to make sure to complete the PWM circuit using the GND terminal on the VFD.

Additional Information:
I have wired my 0-10V signal to the AI1 and GND terminals as suggested. I have also set the PD-01 and PD-02 settings to 1. Still nothing. Is there something else that I am missing?

Additional Information:
Thanks for the information. Can you let me know the model of the VFD that you have?

Additional Information:
VFD Model # YL600-2S-2K20

Additional Information:
Thanks. I will check our resources and documentation to see if there is another programming setting that needs to be changed.

Additional Information:
Does your VFD have a VI terminal?

Additional Information:
No, it does not. The terminals for this VFD are as follows (seperated by dashes "-").

10V-AI1-AO2-PLC-DI5-DI3-DI1-COM
AI2-GND-AO1-DI6-DI4-DI2-FM-24V

Additional Information:
Do you have a PD070 parameter?

PD070 is the main Analog Input parameter.

The options for that parameter is:
0: 0-10V
1: 0-5V
2: 0-20mA
3: 4-20mA
4: 0-10V (4-20mA Stacked)
5: XIA
6: (VI+XIA)/2
7: (3VA+XIA)/4
8: (XIA_XIB)/2
9: Max (XIA, XIB)
10: Min (XIA, XIB)


Additional Information:
There is a PD-00 thru PD-09. PD-07 is currently set to 0.

Additional Information:
It appears that the manual I’m using “Titled YL600” is not the same as your unit. I will check our manuals and find the one that has only PD-00 to PD-09.

Additional Information:
For that VFD, the parameters are P0. The 0 may look like a D on the display.

The parameters that need to be changed for the AI1 to work (Brackets [] around the correct selection):

P0-01: First Motor Control Mode
- 0: Sensorless Vector Control
- 1: Flux Vector Control (FVC)
- [2]: V/F Control

P0-02: Options of Command Source
- 0: Operation Panel Command Channel (LED will be off)
- [1]: Terminal Command Channel (LED will be on)
- 2: Communication Command Channel (LED will flicker)

P0-03: Options of Principle Frequency Source X
- 0: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, no power-down memory)
- 1: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, with power-down memory)
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID (Proportional Integral Derivative Control)
- 9: Communication Given

P0-11: Upper Limit Frequency Source
- 0: P0-12 (Make sure the P0-12 parameter has the correct max frequency if used)
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given

P0-27: Command Source Bundle with Frequency Sources
Single Digit: Options of Operation Panel Command Bundle with Frequency Sources
- 0: No Bundling
- 1: Digital Setting Frequency
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID
- 9: Communication Given
Double Digit: Options of Terminal Command Bundle with Frequency Sources
Hundred Place: Options of Communication Command Bundle with Frequency Sources
Kilobit: Options of Automatic Operation Bundle with Frequency Sources

P2-09: Upper Limit Source of Lower Torque Under Speed Control Mode
- 0: Function Code P2-10 Setting
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given
- 6: MIN (Al1, Al2)
- 7: MAX (Al1, Al2)
- Maximum range for options 1-7, accords with P2-10

If you elect to use a different AI#, then configure the parameters (P0-03, P0-11, P0-27 and P2-09) accordingly.

Click the link to add information to this solution:
I'VE BUFFERED A PWM SIGNAL TO 0-10V ANALOG AND I WOULD LIKE USE THAT RUN YOUR 110V 2.2KW SPINDLE VFD. COULD YOU PLEASE DETAIL THE CORRECT WIRING VFD SETTINGS GET WORKING?

If you remove the dust shoe, you should be able to reach the collet to remove the end mill.

Click the link to add information to this solution:
DO HAVE TO REMOVE THE PORTER CABLE 892 ROUTER EVERY TIME CHANGE BIT?