Did you get a manual for your VFD? Where did you purchase the VFD and spindle?

Additional Information:
I bought the VFD through Amazon with a similar spindle that you sell. The VFD came with a manual but unfortunately the spindle had all the model number and specs scratched off of it. In an attempt to set it up, I fried the spindle. I have complained to the vendor and to Amazon but have received no solution. If your spindle arrives with proper documentation I probably can set it up myself.

Click the link to add information to this solution:
What are the configuration settings for VFD for Spindle 1.5kW 110V. The search settings have a link for a 2.2kw spindle so I'm afraid they are the wrong ones and I don't want to fry the spindle. My VFD is an Huanyang HY01D511B.

Are you using the control panel (front panel with the speed control knob known as he potentiometer)? Or are you attempting to use the computer to control the speed?

Additional Information:
I am using the control panel, however there is no knob on mine, just buttons.

Click the link to add information to this solution:
Hello, I bought your 110v 2.2kw spindle and vfd. When I turn it on it reaches the full 24000 rpm, but will not let me decrease the speed. How Can I fix this?

Ok, I will check the YL600 documentation Monday 4/3 and provide the answer here.

Additional Information:


Additional Information:
I also received one of these and the button labels do not even match your programming instructions as stated on your web set. Please provide updated instruction to match the model shipped with the correct button names to press in The programming process.

Additional Information:
7/15/17 - I have exact problem. I do not see the solution posted???

Additional Information:
Mine is a 2.2Kw YL-620 connected to a 1.5Kw spindle.

Code Address Function Set Range &Function Explanation Factory Setting User Set Vendor Suggested As shipped Code Address Decimal
P00.00 0 Main Frequency 0-120HZ(400HZ） 50.0HZ 　400 60 399.6 P00.0 0
P00.01 1 Start / stop command source 0: Operator board 0 0　 0 P00.1 1
1：From external end control Electric machinery,operation panel STOP key effective
2：From external end son control Electric machinery,operation panel STOP key invalid
3：from (Modbus Rs485) control Electric machinery
4：By user application program control Electric machinery
P00.02 2 Reserved 　 0 　 0 P00.2 2
P00.03 3 Stopping Mode 0：Decelerating stop 0 0　 1 P00.3 3
1：Coasting stop 10
2：DC brake stop 0.2
P00.04 4 VF:Highest output frequency 1.0-120.0HZ(400HZ） 50.0HZ 400 60 400 P00.4 4
P00.05 5 VF:Maximum Voltage Output Frequency 5.0-120.0HZ(400HZ） 50.0HZ 400 60 400 P00.5 5
P00.06 6 VF:Highest output Voltage 10.0%-150.0% 100.00% 100.00% 100.00% 100 P00.6 6
P00.07 7 VF:Middle Frequency 1.0-120.0HZ(400HZ） 3.0Hz 3.5Hz 3.0Hz 3.5 P00.7 7
P00.08 8 VF:Middle Voltage 10.0%-100.0% 10% 20% 10% 10 P00.8 8
P00.09 9 VF:Min Frequency 0-120.0HZ(400HZ） 0.2HZ 0.2Hz 0.2Hz 0.2 P00.9 9
P00.10 10 VF:Min Voltage 0%-100.0% 5% 10.00% 5.00% 5 P00.10 10
P00.11 11 Analog Input quantity 1 Regulation Multistage velocity 0%-100% 100 100 100 100 P00.11 11
P00.12 12 VF :Curve Setting 0-4 0 0 P00.12 12
P00.13 13 Parameter Lock 0: lnvalid 0 0 P00.13 13
1: Valid
10: Restore the factory setting No other function
P00.14 14 Reserved 0 0 P00.14 14
P00.15 15 Power on Time prohibit External end son Start-up 0:Power on time,allow External end input effective level,start-up Electric machinery 0 0 P00.15 15
1:Power on time,Not allow
P00.16 16 0: FWD(X5)yes,Positive run the 0 P00.16 16
1: REV(X6) Determine direction : Open Yes
2:X_EF=EF,X_REV(X5)_DIR=DIR,FWD(X6)=
3: Stop ,FWD(X5) turn off Instantaneous
4: FWD(X5) turn off Instantaneous
5: FWD(X5) turn off Instantaneous
6: Stop ,FWD(X5) turn off Instantaneous
7: REV(X6)When open,FWD(X5)Start-up
P00.17 17 Many function input X1 function Choice ####################################### ####################################### 1 1 P00.17 17
P00.18 18 Many function input X2 function Choice 1.0HZ 1 P00.18 18
P00.19 19 Many function input X3 function Choice 1 P00.19 19
P00.20 20 Many function input X4 function Choice 1 P00.20 20
P00.21 21 External Terminal rise/Slow down increment 0-120HZ(400HZ) 1.0HZ 1 P00.21 21
P00.22 22 External Terminal rise/Slow down time interval 0.2 0.2 P00.22 22
P00.23 23 Physics amount display Proportion constant 0-999.9% 100.00% 100 P00.23 23
P00.24 24 After power supply, display project choice 0: Display current target frequency 0 0 P00.24 24
1:Display Electric machinery run frequency.
2:Display Electric machinery run current.
3:Display input AC voltage
4:Display mother Line voltage
5:Display output voltage
6:Display speed paragraph Number SP x
7:Display inverter temperature t xx
8:Display input signal X1-X3/output signal
9:Display user variable
10:Display user Count value
11:Display temporary debugging variable
12:Display automatic multi segment run step and time
P00.25 25 Display project automatic Return delayed time (10/S) 0:No,Automatic return;1-6delayed 10-60S Back Return 1 1 P00.25 25
P01.00 256 REV Rotation Select 0: Rev Run Enable 0 0 P01.0 256
1: Rev Run Forbidden 0
P01.01 257 Electric machinery Reversing wait for time 0 P01.1 257
P01.02 258 Deceleration Prevention overvoltage setting(%) 130 130 P01.2 258
P01.03 259 Accelerated Prevention overcurrent setting(%) 130 130 P01.3 259
P01.04 260 Overcurrent Set up (%) 200 200 P01.4 260
P01.05 261 Overload protection Set up (%) 130 130 P01.5 261
P01.06 262 Overload protection time Set up (s) 120 120 P01.6 262
P01.07 263 Undervoltage protection Set up (%) 80 80 P01.7 263
P01.08 264 Overvoltage protection Set up (%) 150 150 P01.8 264
P01.09 265 After shutdown, start DC Brake voltage Setup (%) 15 15 P01.9 265
P01.10 266 After shutdown, End DC Brake voltage Setup (%) 0 0 P01.10 266
P01.11 267 After shutdown, DC Braking Time Set up 2 2 P01.11 267
P01.12 268 After shutdown, DC Braking Initial Frequency Set up 0.6 0.6 P01.12 268
P01.13 269 Before start , input DC brake voltage set up (%) 20 20 P01.13 269
P01.14 270 Before start , End DC Brake voltage Set up (%) 15 15 P01.14 270
P01.15 271 Before start , DC Braking Time Set up 3 3 P01.15 271
P01.16 272 Direct start Initial frequency (Improve starting torque ) 100 100 P01.16 272
P01.17 273 Direct start Initial frequency Hold time 0 0 P01.17 273
P01.18 274 power failure frequency decline 80 80 P01.18 274
P01.19 275 The power down frequency decline rate 5 5 P01.19 275
P01.20 276 Restart No load time 10 10 P01.20 276
P01.21 277 Restart voltage rise time 200 200 P01.21 277
P02.00 512 When speed up torque will increased 　 100　 100 100 60 P02.0 512
P02.01 513 Deceleration time - Torque Boost 　 100　 100 100 60 P02.1 513
P02.02 514 Accelerate curve Choice 0　 0 P02.2 514
P02.03 515 Deceleration curve Choice 0　 0 P02.3 515
P02.04 516 Avoid the f requency 1 20 400 P02.4 516
P02.05 517 Avoid the f requency 2 30 30 P02.5 517
P02.06 518 Avoid the f requency 3 　 40 40 P02.6 518
P02.07 519 Avoid the f requency Width 　 0 0 P02.7 519
P02.08 520 Window frequency 1 45 45 P02.8 520
P02.09 521 Window frequency 2 50 50 P02.9 521
P02.10 522 ? 400 P02.10 522
P03.00 768 RS485 Communication Baud Rate 0: 1200Bps 5 4 P03.0 768
1: 2400Bps
2: 4800Bps
3: 9600Bps
4: 19200Bps
5: 38400Bps
6: 57600Bps
P03.01 769 RS485 Communication Addresses 1-254 10 10 P03.1 769
P03.02 770 0: 8 bit data, 1 stop bits, odd parity 2 2 P03.2 770
1: 8 bit data, 1 stop bits, parity check
2: 8 bit data, 1 stop bit, no parity
3: 8 bit data, 2 stop bits, odd parity
4: 8 bit data, 2 stop bits, parity check
5: 8 bit data, 2 stop bit, no parity
P03.03 771 Communication error handling 0 P03.3 771
P03.04 772 Communication error tolerance time 20 P03.4 772
P03.05 773 4-20mA Break detection time 0 P03.5 773
P03.06 774 Panel potentiometer,Lower limit of AD norm 3 P03.6 774
P03.07 775 Panel potentiometer,Upper limit of AD specification 1020 1015 1015 P03.7 775
P03.08 776 Panel potentiometer, frequency given of lower limit 0.0HZ 0 0 P03.8 776
P03.09 777 Panel potentiometer, frequency given of Upper limit 0-120HZ(400HZ） 60.0HZ 400 　60Hz 400 P03.9 777
P03.10 778 Analog lnput 1 AD lower limit 0-1023 3.0Hz 　60Hz 3 P03.10 778
P03.11 779 Analog lnput 1 AD Upper limit 0-1023 1020 1010 1010 P03.11 779
P03.12 780 Analog lnput 1 frequency given lower limit 0.0HZ 0 P03.12 780
P03.13 781 Analog lnput 1 frequency given Upper limit 60.0HZ 400 400 P03.13 781
P03.14 782 Analog lnput 2 AD lower limit 3.0Hz 3 P03.14 782
P03.15 783 Analog lnput 2 AD Upper limit 1020 1010 1010 P03.15 783
P03.16 784 Analog lnput 2 frequency given lower limit 0.0HZ 0 P03.16 784
P03.17 785 Analog lnput 2 frequency given Upper limit 60.0HZ 60 P03.17 785
P03.18 786 Analog output correlation 0 0 P03.18 786


P03.19 787 Analog output gain setting 100 100 P03.19 787
P04.00 1024 Mo analog multiplier output frequency multiplier 10 10 P04.0 1024
P04.01 1025 Mo1 Function Options 0 0 P04.1 1025
P04.02 1026 Mo2 Function Options 1 1 P04.2 1026
P04.03 1027 Multi-function Relay 1 Function selection 0:fault Yes Electric , otherwise power failure 0 2 2 2 P04.3 1027
P04.04 1028 Multi-function Relay 2 Function selection 1:Running Yes Electric ,otherwise power failure 3 3.0Hz 3 P04.4 1028
2: Reserved
3: Arbitrary frequency arrival Time, have Electric,Related to P02-10 settings
4: , The power down Time,have Electric
5:, low voltage Time, have Electric
6:, Overvoltage Time, have Electric
7: Overcurrent Time, have Electric
8: Nonzero velocity Time,have Electric
9:, DC brake Time, have Electric
10: Over torque Time, have Electric
11: External interrupt fault Time, have
12: Forward Time, have Electric
13: Reversal Time, have Electric
14: Move Time, have Electric
15: Accelerate Time, have Electric
16: Deceleration Time, have Electric
17: Constant speed Time, have Electric
18:X1 close Time, have Electric
19:X2 close Time, have Electric
20:X3 close Time, have Electric
21:X4 close Time, have Electric
22:X5 close Time, have Electric
23:X6 close Time, have Electric
24: Forward and bus voltage greater than 400V Time, have Electric
25: Reverse and bus voltage greater than 400V Time, have Electric
P04.05 1029 Multi-function Relay 1 Action close Delayed 0-65.5 S 0 0 P04.5 1029
P04.06 1030 Multi-function Relay 1 disconnect delay action 0-65.5 S 0 0 P04.6 1030
P04.07 1031 Multi-function Relay 1 Action close Delayed 0-65.5 S 0 0 P04.7 1031
P04.08 1032 Multi-function Relay 1 disconnect delay action 0-65.5 S 0 0 P04.8 1032
P04.09 1033 Stall rotor detection time 0-65.5 S 1 1 P04.9 1033
P04.10 1034 Switch amount (Di) sampling time 0-1000mS 8 24 24 P04.10 1034
P04.11 1035 Stopping Mode 0:Decelerating stop 0 0 P04.11 1035
1:Coasting stop
P05.00 1280 PID Output Upper limit frequency 50 50 P05.0 1280
P05.01 1281 PID Output lower limit frequency 25 25 P05.1 1281
P05.02 1282 PID Given Source 0 0 P05.2 1282
P05.03 1283 PID Values Given 0.2 0.2 P05.3 1283
P05.04 1284 PID Output characteristic(FOR /REV) 0 0 P05.4 1284
P05.05 1285 PID Output characteristic (FOR/REV) 0 0 P05.5 1285
P05.06 1286 PID Proportional Gain 0-100.0 50 50 P05.6 1286
P05.07 1287 PID Integration Time Ti 0-100.0 0-100.0 50 50 P05.7 1287
P05.08 1288 PID Derivative Time Td 0-100.0 0-100.0 50 50 P05.8 1288
P05.09 1289 PID Deviation Limit 0-50.0 5 5 P05.9 1289
P05.10 1290 PID Integral upper limit 50 50 P05.10 1290
P05.11 1291 PID Given Change Time 0-600.0 1 1 P05.11 1291
P05.12 1292 PID Feedback Filter Time 0 0 P05.12 1292
P06.00 1536 Acceleration Time 0　 0 P06.0 1536
P06.01 1537 Accel.Time 1 0.1-6553.5 5.0 9 　5.0 5 P06.1 1537
P06.02 1538 Decel. Time 1 0.1-6553.5 5.0 8.6 　5.0 5 P06.2 1538
P06.03 1539 Accel.Time 2 0.1-6553.5 0.1-6553.5 2 2 P06.3 1539
P06.04 1540 Decel. Time 2 0.1-6553.5 0.1-6553.5 2 2 P06.4 1540
P06.05 1541 Accel.Time 3 0.1-6553.5 0.1-6553.5 2 2 P06.5 1541
P06.06 1542 Decel. Time 3 0.1-6553.5 0.1-6553.5 2 2 P06.6 1542
P06.07 1543 Accel.Time 4 0.1-6553.5 0.1-6553.5 2 2 P06.7 1543
P06.08 1544 Decel. Time 4 0.1-6553.5 0.1-6553.5 2 2 P06.8 1544
P06.09 1545 Accel.Time 5 0.1-6553.5 0.1-6553.5 2 2 P06.9 1545
P06.10 1546 Decel. Time 5 0.1-6553.5 0.1-6553.5 2 2 P06.10 1546
P06.11 1547 Accel.Time 6 0.1-6553.5 0.1-6553.5 2 2 P06.11 1547
P06.12 1548 Decel. Time 6 0.1-6553.5 0.1-6553.5 2 2 P06.12 1548
P06.13 1549 Accel.Time 7 0.1-6553.5 0.1-6553.5 2 2 P06.13 1549
P06.14 1550 Decel. Time 7 0.1-6553.5 0.1-6553.5 2 2 P06.14 1550
P06.15 1551 Accel.Time 8 0.1-6553.5 0.1-6553.5 2 2 P06.15 1551
P06.16 1552 Decel. Time 8 0.1-6553.5 0.1-6553.5 2 2 P06.16 1552
P06.17 1553 Jog Acceleration Time 0.1-6553.5 0.1-6553.5 2 2 P06.17 1553
P06.18 1554 Jog Deceleration Time 0.1-6553.5 0.1-6553.5 2 2 P06.18 1554
P07.00 1792 Frequency 1 0-120HZ(400HZ) 50HZ 50 50 P07.0 1792
P07.01 1793 Frequency 2 50HZ 45 45 P07.1 1793
P07.02 1794 Frequency 3 50HZ 40 40 P07.2 1794
P07.03 1795 Frequency 4 50HZ 35 35 P07.3 1795
P07.04 1796 Frequency 5 50HZ 30 30 P07.4 1796
P07.05 1797 Frequency 6 50HZ 25 25 P07.5 1797
P07.06 1798 Frequency 7 50HZ 20 20 P07.6 1798
P07.07 1799 Frequency 8 50HZ 15 15 P07.7 1799
P07.08 1800 Frequency source selection 1 0: Operator board (parameter: P03.06~P03.09) 0 0 P07.8 1800
P07.09 1801 Frequency source selection 2 1: Pre-set Freq, P00.00 Set frequency value,Operation panel keyboard,Can be set directly 2 2 P07.9 1801
P07.10 1802 Frequency source selection 3 2:No. X paragraph frequency P07.00~P07.07 2 2 P07.10 1802
P07.11 1803 Frequency source selection 4 3: Analog Input. :P03.10~P03.13) 2 2 P07.11 1803
P07.12 1804 Frequency source selection 5 4: external simulation amount 2 (VI2) 2 2 P07.12 1804
P07.13 1805 Frequency source selection 6 5: (Modbus Rs485)Given frequency 2 2 P07.13 1805
P07.14 1806 Frequency source selection 7 6: User application program, given frequency 2 2 P07.14 1806
P07.15 1807 Frequency source selection 8 7:( Pid)Output frequency 2 2 P07.15 1807
Other: Reserved
Note:three control methods (P07.08) 1808 1.The motor speed is controlled by the operating panel P07.16 1808
2.Motor speed control by external terminals (Potentiometer 10K). P00.01 set to 1, P07.08 set to 3
3.Motor speed control by external terminals. P00.01 set to 1,P07.08 set to 1.
P07.16 1809 Jogging Frequency FORWARD 0-120HZ(400HZ) 15.0HZ 15 P07.17 1809
P07.17 2048 Jogging Frequency REV 0-120HZ(400HZ) 15.0HZ 13.0Hz 13 P08.0 2048
P08.00 2049 Automatic many paragraph Running: Running direction Binary data format to set the direction of operation, see (the automatic multi segment operation, the operation of the direction set table) 0　 0 P08.1 2049
P08.01 2050 Automatic many paragraph Running: mode Choice 0:Automatic multi segment operation is invalid; 0 0 P08.2 2050
1:After execution complete,Stop;
2:After execution complete,Keep the last running state,Continued running;
3:After execution complete, Repeated execution.
P08.02 2051 Automatic many paragraph Running time Units:S/M 0:S;1:M 0 0 P08.3 2051
P08.03 2052 Automatic many paragraph Running: No.1 paragraph Running time Automatic multi-section run time,Set up Section speed run time。Time units are determined by P08.02 Decision。Set run is 0,Indicates that this section is not executed. 10 1 1 P08.4 2052
P08.04 2053 Automatic many paragraph Running: No.2 paragraph Running time 10 1.5 1.5 P08.5 2053
P08.05 2054 Automatic many paragraph Running: No.3 paragraph Running time 10 1 1 P08.6 2054
P08.06 2055 Automatic many paragraph Running: No.4 paragraph Running time 10 1.5 1.5 P08.7 2055
P08.07 2056 Automatic many paragraph Running: No.5 paragraph Running time 10 1 1 P08.8 2056
P08.08 2057 Automatic many paragraph Running: No.6 paragraph Running time 10 1.5 1.5 P08.9 2057
P08.09 2058 Automatic many paragraph Running: No.7 paragraph Running time 10 1 1 P08.10 2058
P08.10 2304 Automatic many paragraph Running: No.8 paragraph Running time 10 1.5 1.5 P09.0 2304
P09.00 2305 frequency Range(%) 0-200% 0 0 P09.1 2305
P09.01 2306 frequency wave Range(%) 0-400% 200 30 30 P09.2 2306
P09.02 2307 frequency Rise time(S) 0.1-999.9 S 6.0 S 6 P09.3 2307
P09.03 2560 frequency decline time(S) 0.1-999.9 S 5.0 S 5 P10.0 2560
P10.00 2561 Counter reload,value 1000 1000 P10.1 2561
P10.01 2562 Counter current value 0 0 P10.2 2562
P10.02 2563 Timer reload,value 1000 1000 P10.3 2563
P10.03 2816 Timer current value 0 0 P11.0 2816
P11.00 2817 Output Status 1 1 P11.1 2817
P11.01 2818 Output Voltage (V) 0 0 P11.2 2818
P11.02 2819 Output Current (A) 5 5 P11.3 2819
P11.03 2820 Output Frequency (Hz) 50 50 P11.4 2820
P11.04 3072 Current Heatsink Temperature 25 25 P12.0 3072
P12.00 3073 Rated Motor Current 5 5 P12.1 3073
P12.01 3074 Rated Motor Voltage 220 220 P12.2 3074
P12.02 3075 Motor Pole number 2-100 2 2 P12.3 3075
P12.03 3076 Motor no-load current 10 10 P12.4 3076
P12.04 3077 Motor no-load current detection time(S) 10 10 P12.5 3077
P12.05 3078 Converter rated current(A) 5 5 P12.6 3078
P12.06 3079 Converter rated Voltage(V) 220 220 P12.7 3079
P12.07 3080 DC bus output voltage% 140 130 P12.8 3080
P12.08 3081 Heat sink over temperature protection point 70 75 P12.9 3081
P12.09 3082 Radiating fin temperature sensor configuration 1 1 P12.10 3082
P12.10 3083 Abnormal reset implement wait time 120 120 P12.11 3083
P12.11 3084 Fan Function Pattern 0:Motor running tine, start fan; 1 1 P12.12 3084
1:When the fan operating temperature (P12.12) is exceeded,Instant start fan; When the temperature is lower than the fan temperature point,Delay about 1 minutes to close the fan;
2:Unconditional forced start fan;
3:Fan Inoperation;
P12.12 3085 Cooling fan operating temperature 55 45 50 P12.13 3085
P12.13 3086 Fan Testing 0 0 P12.14 3086
P12.14 3087 Bypass relay closed detection 0 0 P12.15 3087
P12.15 3088 Bypass Relay delay time 1.5 1 P12.16 3088
P12.16 3089 Power on delay timer initial value(S) 50 50 P12.17 3089
P12.17 3090 Electric current sensor To configure 1 1 P12.18 3090
P12.18 3091 Automatic stable pressure function Choice 1 1 P12.19 3091
P12.19 3092 PWM Frequency 2.0-15.0KHZ (110V13.0KHZ 220V11.0KHZ 380V6.0KHZ) 8.0KHZ 13.0KHz 13 P12.20 3092
P12.20 3328 SVPWM Pattern 0:Three-phase asynchronous motor, 0 0 P13.0 3328
1:Two-phase asynchronous motor (Single-phase motor, 90 degree phase difference,Starting capacitor)
P13.00 3329 103 P13.1 3329
P13.01 3330 600 P13.2 3330
P13.02 3331 1 P13.3 3331
P13.03 3332 16.24 P13.4 3332
P13.04 3333 1 P13.5 3333
P13.05 3584 0 P14.0 3584
P14.00 3585 35 P14.1 3585
P14.01 3586 0.2 P14.2 3586
P14.02 3587 1 P14.3 3587
P14.03 3588 0 P14.4 3588
P14.04 3589 0 P14.5 3589
P14.05 3590 100 P14.6 3590
P14.06 3591 1900 P14.7 3591
P14.07 3592 2000 P14.8 3592
P14.08 3593 59999 P14.9 3593
P14.09 3594 5 P14.10 3594
P14.10 3595 20 P14.11 3595
P14.11 3596 0 P14.12 3596
P14.12 3597 0 P14.13 3597
P14.13 3598 0 P14.14 3598
P14.14 3599 0 P14.15 3599


Additional Information:
Sorry, that is a paste from a spread sheet, you may have to do some formatting or paste it into a spread sheet to see it better...

Additional Information:
I will definitely do that. Thank you so much for providing the information!!

Additional Information:
I also have this problem with a yl620. Is there a solution?

Additional Information:
Is there a wiring diagram for the 110v units. My came with a 220 volt booklet.

Additional Information:
my unit also came with instructions for a 220 unit. I need a 110 wiring diagram.

Additional Information:
These instructions are lame at best, a friend of mine ordered one of these to install on a knife grinder that I built for him, and I proceeded to setup the unit, upon connecting it to the motor, it runs the motor, but hunt's at the lower speeds, and the setting I am looking for just isn't in the list, there's some settings in the 14's that don't say what there for, can anyone help?

Click the link to add information to this solution:
I received a VFD 110v yl600-2s-2k20 p 110v with 220v instructions, also the connectors on the VFD dose not match any wiring configuration you have.

The configuration settings for our VFD's are these: VFD Setup:
Change PD001 to '0' (source of run commands)
Change PD003 to 300 (main frequency - Hz)
Change PD004 to 300 (base frequency - Hz)
Change PD005 to 400 (max operating frequency - Hz)
Change PD006 to 2.5 (intermediate frequency - Hz)
Change PD008 to 220 (max voltage - V)
Change PD009 to 15 (intermediate voltage - V)
Change PD010 to 8 (minimum voltage - V)
Change PD011 to 100 (frequency lower limit - Hz)
Change PD142 to 7 (rated motor current - Amps)
Change PD143 to 2 (motor pole number)
Change PD144 to 3000 (rated motor revolution)
For further info please refer to (https://www.buildyourcnc.com/item/spindle-inverter-2!2kw-spindle-novfd#prettyPhoto) for wiring and other specifications.

Click the link to add information to this solution:
Can you provide configuration setting for the 110v Huangyang VFD and 1.5 kw spindle?

This will depend on the VFD you have to identify the correct terminal. The terminal on the VFD will be labeled AI1 typically (Analog Input #1). You will also need to make sure to complete the PWM circuit using the GND terminal on the VFD.

Additional Information:
I have wired my 0-10V signal to the AI1 and GND terminals as suggested. I have also set the PD-01 and PD-02 settings to 1. Still nothing. Is there something else that I am missing?

Additional Information:
Thanks for the information. Can you let me know the model of the VFD that you have?

Additional Information:
VFD Model # YL600-2S-2K20

Additional Information:
Thanks. I will check our resources and documentation to see if there is another programming setting that needs to be changed.

Additional Information:
Does your VFD have a VI terminal?

Additional Information:
No, it does not. The terminals for this VFD are as follows (seperated by dashes "-").

10V-AI1-AO2-PLC-DI5-DI3-DI1-COM
AI2-GND-AO1-DI6-DI4-DI2-FM-24V

Additional Information:
Do you have a PD070 parameter?

PD070 is the main Analog Input parameter.

The options for that parameter is:
0: 0-10V
1: 0-5V
2: 0-20mA
3: 4-20mA
4: 0-10V (4-20mA Stacked)
5: XIA
6: (VI+XIA)/2
7: (3VA+XIA)/4
8: (XIA_XIB)/2
9: Max (XIA, XIB)
10: Min (XIA, XIB)


Additional Information:
There is a PD-00 thru PD-09. PD-07 is currently set to 0.

Additional Information:
It appears that the manual I’m using “Titled YL600” is not the same as your unit. I will check our manuals and find the one that has only PD-00 to PD-09.

Additional Information:
For that VFD, the parameters are P0. The 0 may look like a D on the display.

The parameters that need to be changed for the AI1 to work (Brackets [] around the correct selection):

P0-01: First Motor Control Mode
- 0: Sensorless Vector Control
- 1: Flux Vector Control (FVC)
- [2]: V/F Control

P0-02: Options of Command Source
- 0: Operation Panel Command Channel (LED will be off)
- [1]: Terminal Command Channel (LED will be on)
- 2: Communication Command Channel (LED will flicker)

P0-03: Options of Principle Frequency Source X
- 0: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, no power-down memory)
- 1: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, with power-down memory)
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID (Proportional Integral Derivative Control)
- 9: Communication Given

P0-11: Upper Limit Frequency Source
- 0: P0-12 (Make sure the P0-12 parameter has the correct max frequency if used)
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given

P0-27: Command Source Bundle with Frequency Sources
Single Digit: Options of Operation Panel Command Bundle with Frequency Sources
- 0: No Bundling
- 1: Digital Setting Frequency
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID
- 9: Communication Given
Double Digit: Options of Terminal Command Bundle with Frequency Sources
Hundred Place: Options of Communication Command Bundle with Frequency Sources
Kilobit: Options of Automatic Operation Bundle with Frequency Sources

P2-09: Upper Limit Source of Lower Torque Under Speed Control Mode
- 0: Function Code P2-10 Setting
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given
- 6: MIN (Al1, Al2)
- 7: MAX (Al1, Al2)
- Maximum range for options 1-7, accords with P2-10

If you elect to use a different AI#, then configure the parameters (P0-03, P0-11, P0-27 and P2-09) accordingly.

Click the link to add information to this solution:
I'VE BUFFERED A PWM SIGNAL TO 0-10V ANALOG AND I WOULD LIKE USE THAT RUN YOUR 110V 2.2KW SPINDLE VFD. COULD YOU PLEASE DETAIL THE CORRECT WIRING VFD SETTINGS GET WORKING?

The 2.2kW spindle will have the same amount of torque and strength using either the 110V or the 220V inverter. Nothing will significantly change in either application since the 110V inverter has a small step up transformer which will increase the voltage from 110V to 220V to run the spindle efficiently.

Additional Information:
I'd like confirmation on this -- isn't there a cost in efficiency to having the 110v step up to 220v?

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Click the link to add information to this solution:
Good morning, I would like to know if the strength of the 2.2kw spindle is weaker when using the 110V version of the VFD. Does it have the same power as the 220V version VFD?

This will depend on the VFD you have to identify the correct terminal. The terminal on the VFD will be labeled AI1 typically (Analog Input #1). You will also need to make sure to complete the PWM circuit using the GND terminal on the VFD.

Additional Information:
I have wired my 0-10V signal to the AI1 and GND terminals as suggested. I have also set the PD-01 and PD-02 settings to 1. Still nothing. Is there something else that I am missing?

Additional Information:
Thanks for the information. Can you let me know the model of the VFD that you have?

Additional Information:
VFD Model # YL600-2S-2K20

Additional Information:
Thanks. I will check our resources and documentation to see if there is another programming setting that needs to be changed.

Additional Information:
Does your VFD have a VI terminal?

Additional Information:
No, it does not. The terminals for this VFD are as follows (seperated by dashes "-").

10V-AI1-AO2-PLC-DI5-DI3-DI1-COM
AI2-GND-AO1-DI6-DI4-DI2-FM-24V

Additional Information:
Do you have a PD070 parameter?

PD070 is the main Analog Input parameter.

The options for that parameter is:
0: 0-10V
1: 0-5V
2: 0-20mA
3: 4-20mA
4: 0-10V (4-20mA Stacked)
5: XIA
6: (VI+XIA)/2
7: (3VA+XIA)/4
8: (XIA_XIB)/2
9: Max (XIA, XIB)
10: Min (XIA, XIB)


Additional Information:
There is a PD-00 thru PD-09. PD-07 is currently set to 0.

Additional Information:
It appears that the manual I’m using “Titled YL600” is not the same as your unit. I will check our manuals and find the one that has only PD-00 to PD-09.

Additional Information:
For that VFD, the parameters are P0. The 0 may look like a D on the display.

The parameters that need to be changed for the AI1 to work (Brackets [] around the correct selection):

P0-01: First Motor Control Mode
- 0: Sensorless Vector Control
- 1: Flux Vector Control (FVC)
- [2]: V/F Control

P0-02: Options of Command Source
- 0: Operation Panel Command Channel (LED will be off)
- [1]: Terminal Command Channel (LED will be on)
- 2: Communication Command Channel (LED will flicker)

P0-03: Options of Principle Frequency Source X
- 0: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, no power-down memory)
- 1: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, with power-down memory)
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID (Proportional Integral Derivative Control)
- 9: Communication Given

P0-11: Upper Limit Frequency Source
- 0: P0-12 (Make sure the P0-12 parameter has the correct max frequency if used)
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given

P0-27: Command Source Bundle with Frequency Sources
Single Digit: Options of Operation Panel Command Bundle with Frequency Sources
- 0: No Bundling
- 1: Digital Setting Frequency
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID
- 9: Communication Given
Double Digit: Options of Terminal Command Bundle with Frequency Sources
Hundred Place: Options of Communication Command Bundle with Frequency Sources
Kilobit: Options of Automatic Operation Bundle with Frequency Sources

P2-09: Upper Limit Source of Lower Torque Under Speed Control Mode
- 0: Function Code P2-10 Setting
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given
- 6: MIN (Al1, Al2)
- 7: MAX (Al1, Al2)
- Maximum range for options 1-7, accords with P2-10

If you elect to use a different AI#, then configure the parameters (P0-03, P0-11, P0-27 and P2-09) accordingly.

Click the link to add information to this solution:
I've buffered a PWM signal to a 0-10V analog signal and I would like to use that signal to run your 110V 2.2kW spindle and VFD. Could you please detail the correct wiring and VFD settings to get that working?

Yes. The VFD (Variable Frequency Drive) has a large set of parameters that can be modified. This is typically called "programming" the VFD. The parameters can be accessed using the front control panel of the VFD.

Since the VFD is the mechanism that control the allowable current draw from the spindle, there is a parameter that assigns the motor rated current; however, it is probably better to match the rated current of the motor and "up" the circuit breaker current instead. If the current limit is set too low, then there is a possibility that the spindle will cause a current overload error on the VFD and cause the spindle to stop.

Click the link to add information to this solution:
With your 120v drive systems for your 2.2kw spindles, do you do something to limit the output to the spindle so that the current draw doesn't exceed the 80% limitations of a 20a circuit? I have a dedicated circuit for my router and I am considering a spindle upgrade, but I am curious how the configuration matches the math.

I am getting the solution from the developer. I will put the solution on this page when they provide the solution.

Thanks, Patrick

Additional Information:
Here is the information I received from the developer:

These are available on Windows 10. PoBlocks does not require .NET, but the communication library that the PoKeys app uses does need it.

Go to the control panel -> Search for "Turn Windows features on or off" -> Make sure the checkbox on the line ".NET Framework 3.5 (includes .NET 2.0 and 3.0)" is checked (or filled in).

Click the link to add information to this solution:
[596] I am trying to install the Pokeys configuration and Poblocks on a windows 10 computer. An error message says Ineed net frameworks 2.5 qnd 3.0.Both appear to be unavalable.Solution?

You can find the wiring diagram for the 2.2kW spindle and, follow through instructions here.
https://www.buildyourcnc.com/item/spindle-inverter-2!2kw-spindle-novfd#prettyPhoto/8/

Additional Information:


Additional Information:
wiring diagram at spindle top


Additional Information:


Additional Information:


Additional Information:


Additional Information:
Can you please provide settings for a 110v 2.2 spindle vfd

Additional Information:
Can you please provide settings for a 110v 2.2 spindle vfd

Click the link to add information to this solution:
How should I wire the 2.2kw spindle and vfd?

Strictly to the point. Assuming:
-You have a working linuxcnc install with a compatible parallel port
-You have wired Bread-Out Board V5 to the motor drivers so you know which pins are for which signals(watch video tutorials for that on this site)
-You have wired motors to motor drivers (watch video tutorials for that on this site)

a)We need to know the base parallel port addres, for that you need to input on a linux terminal the command:

#lspci -v

You can scroll up and down the result with page up and page down. Look for a "Parallel Port..." line, the value you are looking for is the "I/O Ports at.." Write them down

To get the Base Period Maximun Jitter, go to
applications - cnc - Latency Test

Now you should let that window running for a while, so it calculates an accurate jitter, go watch the tutorial videos for the connections between the Bread-Out Board and the motor controllers.

After its been running for half an hour or so with the machine in use, write down the calculated jitter values, mine was Servo Thread - 39000

Now close the Latency test dialog

b)Go to applications - cnc - stepconfwizard
"START" - Create a new config
Check - Create Desktop Shortcut to config files
Check - Create Desktop Shortcut to start linuxcnc with this config
FORWARD

c)"BASE INFORMATION"
Fill in a Machine Name that suits you
Bluechick is XYZ on inches
Fill in the Base Period Maximun Jitter with the value obtained in "a)"

FORWARD

d)If you watched the tutorials on a) and b) you know the pin numbers for your signals.
Parport Base Address you need to put the value obtained in a), mine was cf00
Output pinout presets I used Sherline

FORWARD
FORWARD

e)Axis X (chain and sprocket axis)
Data for bluechick from build yourcnc
Motor Steps per revolution 200
Microstepping 64 (that if you followed tutorials, change if you have different)
Pulley teeth 1 ; 1
Leadscrew Pitch 0.444444 (that value comes from 1rev / (.25 in * 9 teeth))
Maximun Velocity 10
Maximun Acceleration 0.5
Home location 0.0
Table travel 0.0 to 34.0 (maybe you want to change this later)

Now, you can do "Test this axis" and jog it (move it!) Try to position everything in the middle (you will be doing it axis by axis) and select
"+ 0.5 in" Hit run, I used a pencil held at the gantry and paper to draw a line, then confirmed that the measurement was 0.5 in. Also tried with "+/- 0.5 in" and confirmed 1" measurement

FORWARD when happy with your Axis X

Repeat for Axix Y but the table travel is 0.0 to 12.0

f)AXIS Z
With data from buildyourcnc.com
Motor Steps per rev 200
Driver Microstepping 16 (as recommended for lead screw)
Pulley teeth 1 ; 1
Leadscrew Pitch 2
Max Vel 2.5
Max Accel 0.5

Table travel 0.0 to 3.5

Test, and FORWARD when happy

g)After configured you can go to
Applications - cnc - LinuxCNC, and there you go...




Additional Information:
... Still think that there should be a tutorial for this part.

Additional Information:
oh¡ Forgot to tell, the config shortcut will be available on our Desktop, launch linuxCNC from there

Click the link to add information to this solution:
I have a BlueChick that came with the 5-Axis Bread-Out Board V5 (parallel port), it has 3xCW230, how to configure it on LinuxCNC?

What laser controller model number do you have?

Additional Information:
Hey - the model number on the laser controller is
AWC708C
S/N:708014243

Additional Information:
Thanks for the model number. I am going to fabricate the parts and put it together myself to see the issue. We made this modification to the blackTooth laser cutter to better house the new laser controller that we wanted to add to the laser, but that may have been for the AWC608. If there is an issue with my assembly, we will create a new part that will correct the issue and send it to you.

Additional Information:
Thank you for the update!

Additional Information:
Have you had a chance to duplicate the issue yet?

Click the link to add information to this solution:
There are no instructions on how to assemble the laser control unit housing that came with my 40w blacktooth laser kit. How can I get instructions for how to assemble the control interface housing? Every configuration I try blocks the wire connection ports.

Take a look at these two videos that I created today on Instagram on the proper wiring of a relay to the Mach3 USB controller.

https://www.instagram.com/tv/CMYGGBtj3cq/?utm_source=ig_web_copy_link
https://www.instagram.com/tv/CMYLvq9DXVK/?utm_source=ig_web_copy_link

Don't forget to watch the initial video on the Mach3 USB outputs on the Mach3 USB product page (last video on that page):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
i would like to turn on my water pump with out3 or 4 when i turn on the spindle. I have Mach3 working with the spindle on out1and 2. I have a relay wiredbut cant get out3 to flip.

Absolutely. You can have 1/2" collets used in 2.2kW spindles.

Here is a link for the ER-20 1/2"ID Collet:
https://www.buildyourcnc.com/item/spindle-collet-!5-er20-spindle-collet

Click the link to add information to this solution:
2.2kW Spindle with 110V Inverter, can I get a collet for 1/2 router bits for this spindle

The outputs are independent of the PWM function of the controller. The PWM uses the ACM and AVI outputs from the controller to the VFD along with the 10V input from the VFD to the controller. The 10V input serves as an upper voltage reference for the PWM output. The PWM output is discrete and does not connect with the ON/OFF outputs 1-4 terminals. Did you try testing the outputs without using the AVI and ACM PWM function?

Click the link to add information to this solution:
[575] Depending on the command I use (M3 S50, M3 S100, M3 S70) at a pmw base 100, Ill get not just output 1 with 24v, also outputs 2 3 or 4. Tested on 2 different boards and I just can't find the problem; at the configuration there is only output 1 enabled (port 3 pin1)

Yes, the RNRMotion.dll file must be used and put in the plugins folder under the Mach3 folder.

The XML file that I link on the Mach3 USB controller page is the file you should start with. This file will have the necessary configuration that links the Mach3 USB controller to the Mach3 control software. You can then make whatever changes you need to this configuration to tailor it to your machine.

Do you see a quick flashing red led on the board when you press the arrow keys?

Additional Information:

Click the link to add information to this solution:
[575] Do I have to use the motion driver and configuration file to use this card? The x,y,a shows that it's moving on display, but the motors aren't moving.

I recommend using a an output terminal to turn on and off the laser for safety. All you need to use is the M7 (or 8) to turn the laser on and M9 to turn it off. These M codes are use in conjunction with the output terminals to control external devices. The last Pokeys57CNC tutorial part explains this concept. You can use this idea with your controller.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
How do you configure usb cnc and the mk1 board to toggle the laser? I use jscut.org to create gcode files and am wondering if I create a setting to disable the laser when it goes a certain distance above 0 on Z+.

The 2.2kW spindle has a power rating of 2.2kW or 2200 watts.

If the VFD AC voltage input is rated for 220 volts, then 2200 watts / 220 volts is 10 amps, so a 15 or 20 amp breaker will work.

If the VFD AC voltage input is rated for 110 volts, then 2200 watts / 110 volts is 20 amps, so a 25 or 30 amp breaker will work.

Additional Information:



Additional Information:

Click the link to add information to this solution:
what size circuit breaker should I use with the 2.2KW VFD?

The VFD does come with a manual that details the wiring and connection specifications, terminal features and a list of the parameters. There is no information on how to connect it to Mach3. It does detail the specifications within the parameters and terminal features on the analog input that is used with Mach3 and other control programs.

Click the link to add information to this solution:
I have a water cooled spindle I only need the VFD drive. Does the VFD come with instrutction on hooking the VFD to Mach3?