Yes, we can create an only wood kit for you. Please give us a call on Monday to provide your name so we can look it up in our system to confirm your previous purchase and we will provide a PayPal invoice for the kit, since this is a special case.

Click the link to add information to this solution:
Is it possible to purchase the wood pieces only for a BlackToe 2.0/2.1? I have all of the hardware from my kit, but the wood pieces were lost in a recent move.

Yes, the knife you are referring to is called a tangential knife and is available here https://buildyourcnc.com/Item/endmill-Tangential-cutting-Dragknives-Donektools-D2

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I want to build a similar CNC to the Blacktoe 2'x6' design that Matt Gottscualk built. Is it possible to also outfit a small knife tip/setup for very precise cuts in vinyl/plastic?

The book pdf documents are on this page:
https://www.buildyourcnc.com/Book.aspx

Just click on the red area in the first paragraph that states: Click here for the book's documents.

Or, you can just go here for the documents directly for your convenience:
https://www.buildyourcnc.com/Documents/CNC%20Kit%201-1.pdf

Additional Information:
The mdf sheets layout are here:
https://www.buildyourcnc.com/Documents/cuts-Layout1.pdf
and here:
https://www.buildyourcnc.com/Documents/cuts-Layout1%20(2).pdf

Click the link to add information to this solution:
in the book page 18 it says the are down loadable pdf files containing the measurements of the mdf sheets I can not find them on your site even under the book tab

Sure, we can send you a replacement LED indicator. Just send an email to customerservice@buildyourcnc.com, include your address and we will send it poste haste.

Click the link to add information to this solution:
The LED Status indicator on the front of my Blacktooth laser is not working any longer. I'm looking to get a replacement but can't seem to find them on your website. Do you sell replacements? Thank you.

Yes, if the power supplies were supplied by us, we will exchange them with 110v equivalent power supplies.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hello, I am a student working on a CO2 laser. We recently ordered two 40watt CO2 laser tubes and two 40 Watt CO2 Laser Tube Power Supply at 220V. However, our school is unable to use them due to being 220v. Is it possible to exchange these for the 110v supply, or is there a way we can go about connecting it at 110v instead of 220v? Thank you.

Not a problem. The ALM is rather self-explanatory as this is a closed-loop stepper motor and driver that you are using. The ALM (alarm) is a signal that is used to tell the driver/controller that the motor is not in the same condition that the driver expects. In a closed-loop system, the motor has an encoder that tells the driver exactly how many steps that it turned, and if this value does not coincide with the driver's outputted number of steps, and within a specified amount of time, the alarm will trigger so the system can stop and the workpiece can be salvaged.

The MF is simply a signal that tells the driver that there is impending direction and step pulses coming. If the MF signal is high, then that is similar to an enable signal.

Click the link to add information to this solution:
Hello I recently read your site and have a question. I have a driver model DM2722A but I can't connect it to my usb controller due to the fact that the driver is not marked enable, but instead it is marked: mf-, mf +, alm-, alm +. I will be very grateful if you explain to me the meaning of the latter and tell me what should be related to "enable" Thanks in advance!

it is possible to install 2 motors on a single axis but you will require another driver and motor, but wire it directly to the same pins on your breakout board. Also the orientation of your motor since it is opposite side of the original so getting it to move accordingly to the original motor it will need to be orientated correctly. The slight shift could be the cause of the rod not being completely flat where the set screws are suppose to tighten the sprocket to the rod, so sanding it to a flatter surface might fix the shift in directions.
Currently do not have a kit or schematic available.

Click the link to add information to this solution:
Hello, I have a BlackToe 2 x 4 machine. I was wondering if it could be beneficial, or even possible to install two motors on the x-axis (one one each chain drive sprocket). I am noticing a slight shift in the gantry with each reversal of direction. If so, do you have a kit or schematic for this? Thanks

You will need to look for the parameter that controls the run frequency. The frequency can be controlled bu the panel, external terminals, or the RS485 TX/RX terminals (UART protocol). You will want to change that parameter so it uses the panel. If you are referring to the maximum panel dial frequency is only allowing 200-300 rpm, then look for the parameters to control the frequency.

For 200 RPM:
Hz = 200/60 = 3.33 Hz

For 300 RPM:
Hz = 300/60 = 5 Hz

Conversion to RPM:
If you ever find yourself yearning to reverse-engineer the process, the formula is as follows:

RPM = Hz × 60

Look for values that match somewhere between 3 and 5 in your frequency parameters and replace them with 400 to give you 24,000 RPM max.

Click the link to add information to this solution:
[77] Hello. I’m interested in buying a water cooled spindle and VFD. I have an Avid Pro CNC and would love to control it using Mach 4 but I keep hearing it’s difficult to integrate. Also, is the water pump 120 or 240? I’d love any advice etc. eBay is a web of confusion with all of the options. Thank you.

Yes, you can purchase the blackToe 2'x4' CNC machine kit without the optional table.
https://buildyourcnc.com/Item/cnc-machine-blacktoe-v4-2x4

The 4th axis product can be found here:
https://buildyourcnc.com/item/axes-4th

We recommend Mach3 or LinuxCNC to control the machine:
https://buildyourcnc.com/item/control-SOFTWARE-mach3
https://buildyourcnc.com/item/control-SOFTWARE-linuxcnc

When you go to the cart to check out, the shipping prices will be displayed when you click on the calculate shipping button.

The instructions to assemble the machine is on the product pages of the machine and parts you purchase. See above links.

Click the link to add information to this solution:
hello, is it possible to send all components of a 4Axis CNC in size of ( about 2' x 5' ) to Iran country without table and all required manuals and measurements to create and assemble cnc machine and table plus required software? i need total price for this request if it's possible for transfer.

Yes, servo motors can be mounted on this machine. If the mounting dimensions are different than NEMA 23 or NEMA 34, then all you need to do is keep the center of the motorshaft with the center of the bearing location and locate the mounting holes for he servo you wish to use. Most industrial servos used for these machines share the same mounting dimensions and NEMA specifications.

Additional Information:
This machine is one of the most customizable machines out in the wild. Customers of these machines have fashioned many modifications to suit their needs.

Additional Information:
20

Click the link to add information to this solution:
[796] Hello. To what extent can the design plans be customized? For example, if I wanted servo motors instead of steppers? That would requirements for motor mounting, controls, and electrical. Thank you.

I just posted the "enhanced" Blacktooth wiring diagram I developed. Check it out here.

http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Click the link to add information to this solution:
Where do I wire the ground of my "th" and "power 0v - 5v" command on the power supply ? Is it possible to have a detailed blueprint of the electrical wiring (not for the blacktooth but in general) ? Many thanks :)

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
I am building the CNC in your book - Build you own CNC Machine. One of the bearing thicknesses is 1/4" I can't find that bearing online. I can find 9/32, will that be a problem. Do you have a source? Thx

Absolutely! You can have almost unlimited limit switches and home switches on this controller. It all comes down to the wiring scheme used. I recommend the home switches be on separate input terminals. For example, IN1 would have the X home switch, IN2 would have the Y home switch and, IN3 would have the Z home switch if you plan on using home switches for the Z axis.

Adding the limit switches, these can be located on any input you want, even on the IN1, 2 or 3. The wiring scheme I like to use is as follows:
- IN1 has the X home, X limit ++, and X Limit --
- IN1 has the Y home, Y limit ++, and Y Limit --
- IN1 has the Z home, Z limit ++, and Z Limit --

In most cases, the Limit -- is the same switch as the Home switch.

These can be wired as NC (Normally closed) as a serial scheme, or as NO (Normally open) as a parallel scheme.

To understand the limits and wiring schemes, check out this video:

Click the link to add information to this solution:
[575] Hi, for the manage the limit switches, is it possible to have, for example, the same limit switch for X-- and X homing? And what is the configuration in mach3? In my CNC machine they are in the same position. Thank you

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
IT POSSIBLE TO BUY THE CAD FILES FOR BLACK FOOT MACHINE, MECHANICAL PARTS AND ELECTRONICS BUT NOT WOODEN PARTS, SAVE SHIPPING COSTS? IN THAT CASE I WOULD INSTRUCT SOMEONE MILL ME.

Our spindle VFD's, have a multitude of different connectors that can be used for different operations. There is a manual that comes with each VFD, and you can refer to page 11 for different functions and descriptions.

We currently have a PWM, working with our machine, however it is connected via USB, and setup through Mach 3.
Also if you may have misplaced or lost the manual here is a link to the pdf:

(https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0CCAQFjAAahUKEwibxaaIndTHAhXQlogKHZVyDFE&url=http%3A%2F%2Fwww.c-n-c.cz%2Fdownload%2Ffile.php%3Fid%3D42252&ei=_cHkVdvSC9CtogSV5bGIBQ&usg=AFQjCNHTQcxs-KhJkvkhMdxVFPzkoYJtsA&sig2=JAcZawTGMuC-t4wmn1z-rA)

Click the link to add information to this solution:
It is possible to control externally the 1.5kW Inverter (VFD) (220 Volt) with PWM so i can control the spindle rotation? Do you have the documentation? Thank you

If you would like to see a machine in action, you can go to the forum and make a request in the buildyourtools.com forum.

Click the link to add information to this solution:
I am interested in the blacktoe but want to see on in operarion personally. is there one in lower Michigan. I live in Hillsdale Michigan area.

The electronics can be tricky sometimes, especially if more than one change is made for a test. You can move the x-dir wire to another pin and set it in the software configuration. If it works, then only that pin is bad.

Click the link to add information to this solution:
ON THE BOB...EVERYTHING TESTS OK BOB EXCEPT X-DIRECTION OUT. IT'S VOLTAGE IS SLIGHTLY DIFFERENT THAN Y AND Z (5.00 INSTEAD OF 5.03. TESTED X DIRECTION ALL THREE DRIVERS. IN EACH CASE THERE GOING INTO DRIVER BUT NOT OUT IT.

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
Is it possible to buy just the electronics and hardware for the bigfoot along with the plans for the timber components so that I could have them cut here in the UK and reduce the amount of material that needs to be shipped?

We could not guarantee, nor say, whether or not your current software would be able to utilize the USB breakout board. Our USB breakout board is designed for use with Planet CNC software found here, http://www.planet-cnc.com/index.php?page=software

As far as we know, this is the only CNC Controller software that operates on a USB breakout controller.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I want to change my old DSP controller and break out board with new one in your site that support usb it is possible ? if yes can we contact us to talking about details ?