For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
The electronics package I just bought from you (Book Build) is different from your wireing diagrams and video tutorials. Is there an updated wiring diagram available? Is the USB port on the breakout board connected directly to the computer USB to supply 5 volts? Thank you.

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

The digital signal portion of the CO2 laser tube power supply has various terminals for signal power, signal gnd, laser intensity and engaging the laser (turning it on or off). The TL and TH are triggers to turn the laser power on or off. These may be labeled L or H on some laser power supplies. You can use either TL/L, or TH/H to control the laser.

If you use the TL or L terminal to control the laser:
If a low signal (gnd) is present at that terminal, the laser will turn on. If a high signal (5v) is present, the laser will turn off.

If you use the TH or H terminal to control the laser:
If a high signal (5v) is present at that terminal, the laser will turn on. If a low signal (gnd) is present, the laser will turn off.

You should first test the control signal from the interface with a multimeter to make sure the laser will be controlled correctly before powering the laser power supply

Click the link to add information to this solution:
On the blacktooth machine wiring diagram for parallel breakout a wire goes from 6 on the BOB to TL on the laser power supply. My power supply has an"H" followed by a "L". Which is correct? I've connected to the "L" but the laser appears always on.

I can provide a paypal invoice for the difference in price. Just give me an email at customerservice@buildyourcnc.com and then I can send you the invoice.

Additional Information:
I can provide a paypal invoice for the difference in price. Just give me an email at customerservice@buildyourcnc.com and then I can send you the invoice.

Additional Information:
thats great thank you. please send it to james_moya@hotmail.com and i will be paying with my cc.

Additional Information:
thats great thank you. please send it to james_moya@hotmail.com and i will be paying with my cc.

Click the link to add information to this solution:
i placed an order with you on 5.27.20 for 3 stepper motors. i realize now i need the rest of the electronics (drivers, breakout board power supply etc...) i see you offer a bundle and would like to know how i can get the rest of the bundle. im looking at the $390 bundle without the motors obviously. please advise. thank you

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I am making my own CNC setup using all the electronics from your website and I have many questions. Please advise how to have my computer recognize the USB connection from my breakout board also I would like to use a water cooled spindle but I need to know the parts required for a 4x10 bed area used for woods and plastics

What we intend our customers to use for wiring the motors to the drivers will be 4 conductor 20 AWG cable, now for the PSU to Drivers; 16-18 Gauge wire should be used, and drivers to BB(Breakout Board) should be a 24 AWG wires.

Click the link to add information to this solution:
In my 4'x8' Blackfoot rig, there is a maximum wire length of 16" between drivers, breakout board, and power supply as well as a maximum wire length of 10' from drivers to motors. What AWG wires should I use to connect power supply to drivers, drivers to motors, and drivers to breakout board?

First, see Jack's build: https://www.buildyourcnc.com/JackRehak.aspx

The difference between mounting the electronics in the gantry is that the connection from the computer (signal level) is long. The alternative, where the electronics is near the computer, the motor cables are long (to reach from the drivers to the motors).

Mounting the breakout board, drivers and power supply within the gantry will cause you to have a long signal connection from the computer to the breakout board. That is fine as long as the cable is long enough, possibly shielded, and can carry the signal at long cable lengths. Make sure to have the cable well away from the motor cables as these will cause quite a bit of interference.

Click the link to add information to this solution:
Provided they will fit and I install a ventilation/cooling fan, is there any reason why I should NOT mount the electronics (breakout board, stepper drivers and power supply) inside the gantry box in my BlackToe 2x4?

Which controller card are you using?

Click the link to add information to this solution:
USB connection can not move the gantry, it is connected but noticed in device manager is missing drivers. PCI serial port... any help would be great also there is two mach3 profiles one showers numbers moving as like the gantry should be but is not.

The stepper motor on the X axis on the VLXL is this motor here:
https://www.buildyourcnc.com/item/electronicsAndMotors-nema34-651ozin

There is no black lead on that motor and the connection diagram can be found here:
https://www.buildyourcnc.com/Documents/PN.SM86HT80-5504B-U(inhouse%20PN.85BYGH450A-47-80)%20(1).pdf

Red - A+
Green - A-
Yellow - B+
Blue - B-

The wiring diagram on the instructions for the Vertical Laser XL is meant as a general guide for all laser systems. The motor specific to the axis should be checked against the datasheet to insure proper wiring.

The 24V power supply should be connected to the laser controller. The 36V power supply should be connected to the drivers to power the motion electronics.

Additional Information:
My fault. Must have had that backwards. I'm sure he told me the right way.

Additional Information:
Not a problem. The laser controller has two terminals labeled for the 24V connection.

The 36V power supply works really well for stepper motor drivers as the voltage/current on this power supply allows for best stepper motor performance with this laser application.

Click the link to add information to this solution:
Hello! Question about the x motor on the vlxl. There is no black lead. Is the yellow in its position? Also, I really just want to double check that this wiring diagram is solid. About to finish the wiring. Juan told me to use the 36V for the tube and 24 for the drivers. Correct?

By USB power do you mean the USB board? or do you mean that it is powered through USB but you have the parallel breakout board?


Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Click the link to add information to this solution:
I'm new to this and was wondering if I connected something incorrectly... I followed the schematics found on this site for wiring. I purchased the heavy gantry kit with the USB power option. All my lights come on and motor shafts resist turning but, I cannot get movement from Mach3. How do I test my equipment to see if I've damaged anything?

If one or more motor is not responding, please follow the troubleshooting directions below:

For parallel Bob only! Make sure both the parallel and USB are connected.

Re-check wiring, and connections for continuity (no breaks in the wires) and check for correct wiring locations from driver to BoB.
Check dip switch settings on the driver.
Check components, by swapping the motors (ex. y-axis motor to z or x-axis driver and z or x-axis motor to y-axis driver) to check if motor functions on another driver.
Depending on software check step low active (mach 3) or invert pulse (planet-cnc) for the axis which is not responding.
Mach 3 - config/port & pins/motor outputs / Planet-CNC - file/settings/axes

Click the link to add information to this solution:
I have an engine NEMA 34 from Y axis on my green bull that do not response, I already check connections and everything seems to be OK, how can I check that the motor it's working properly or not?

https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-e-stop-button-switch-safety#prettyPhoto/0/

Click the link to add information to this solution:
How do I wire up multiple E-stop to breakout board, does each E-stop need there own pin? If not since there are only 4 screws on stop 2 for no and 2 for nc do you just splice the wires together if your only using 1 pin? Thanks

Does the machine move smoothly when using the keyboard to jog the machine?

Additional Information:
Sorry it took so long to respond. Yes the table moves very smoothly using the keyboard. I try to reinstall of the drivers but it still moves very jerky with the MPG, sometimes moving back-and-forth.


Additional Information:
Sorry it took so long to respond. Yes the table moves very smoothly using the keyboard. I try to reinstall of the drivers but it still moves very jerky with the MPG, sometimes moving back-and-forth.

Click the link to add information to this solution:
Hi I recently replaced my parallel port breakout bored with a USB breakout board, Motors Earl working properly but my wireless MPG is not working properly, it is jerky when to try to move across the table, is there a setting that I missed?

The whiteAnt is no longer sold; the information on the website is to support legacy customers. We have spoken with you and are sending the materials that you need.

Click the link to add information to this solution:
I am having difficulty with the wiring on the White Ant. The latest electronics that I received don't seem to be anything like the book or even the tutorials. For instance, the three stepper drivers need 6 pin connectors and ribbon cable. How are they wired? There was no thermocouple wire included. Thanks,

Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

Additional Information:
Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

Click the link to add information to this solution:
Hi, I need assistance, the parallel breakout board I received looks different from the one on the video, does this one need a 5V supply? If so, where do I connect the positive and where do I connect the ground? Thanks for your help.

Our breakout board, does require 5v to operate the correct voltages coming in from the drivers and also coming in from your computer, now the 5V will be supplied by the USB connection, so no external power supply is needed, for either our USB/Parallel breakout board.

Click the link to add information to this solution:
Just for general knowledge. If a spindle gets i.e. 240VAC, and the drivers 36-50VDC for power, why do you need 5VDC for the Breakout Board (BlueBrew)? Is it only for the relay? I think I've seen other BoB's working without power supply, or am I wrong?

If the sensors are NC (normally closed) you can wire them in series. If the sensors are NO (Normally Open) you can still wire them to the same input, but the wiring needs to be in parallel (like a ladder). I have more information on the following video:

Click the link to add information to this solution:
[788] Thanks for the oportunity to ask, I am building a cnc and using npn closed sensors could you help me with the conection of these, do i still connect them in series if i use more than two in each axis. Also you mention that a stop switch should be connected grd and input to the controller would that be done after the 24v power supply. Thanks r

Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

Additional Information:
Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

Click the link to add information to this solution:
Hello, we are trying to assemble a kit and the breakout board rev 2.1 that we have does not match the video... we do not see where to connect the 5v powersource to finish step #3, can you provide a location for the power hookup for our board.

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am wiring my breakout board and it has a USB port on it. Is the USB port there to supply the 5 volt power to it?