On "our" VFDs, we advise that the R connect to black (live), T connect to white (neutral) and green to E or earth. We are not professional electricians, so we also recommend that you seek the advice of a professional electrician. Some VFDs are made to work on 3 phase power and this configuration may not work with these VFDs.

Click the link to add information to this solution:
On your diagram it says to connect the power to the VFD in port L1, L2 and PE. On the VFD I have there is no L1 or L2. Which ports do I connect my input power to? There is only a P+, P-, R, S, T, U, V, W, and PE. What do I do?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

Red is A+
Blue is A-
Black is B+
and Green is B-

Click the link to add information to this solution:
I purchased the 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller and the motors supplied only have 4 wires coming out of them (R,G,B,Blk). Your wiring video shows wiring 8 cables. do you have a video showing how to wire the 4 wire version?

You can find a diagram that describes the pin-out for the 2.5 am Driver that is intended for the 3D Printer Main Board, but can be used as a standalone driver as well.

Additional Information:
Where is the diagram located?

Click the link to add information to this solution:
Is there a diagram or schematic showing which pin on the 3D printer driver is ABCD?

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

You can find a wiring diagram here:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

The CP terminal is wired to the step terminal on the 8825 step driver.
The CW terminal is wired to the direction terminal on the 8825 step driver.
The GND terminal connects to the GND on the 8825 step driver

The 5V connector on the driver simply powers the logic side of the chip and needs to connect to VCC pin on the keyboard jog.

Customer Response:
Thanks! Working now.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

The greenBull instructions are found on our website. Each machine has a page, which you can locate by clicking on "CNC Machines" from the left hand menu and choosing the particular machine you have. Scroll to the bottom of that machine page and you will find complete instructions. The page for the greenBull 5X, for example, is : https://buildyourcnc.com/Item/cnc-machine-greenBull-v4-5X

The redFly is typically sold with motors already wired to conductor cable with 4-pin connectors; these need simply to be plugged into the control box. There is no soldering required. If you have a different configuration, please contact us directly at techsupport@buildyourcnc.com with information about your specific application (and a photo, if possible) and we will be happy to provide you with further guidance.

Click the link to add information to this solution:
How do I know how to hook up the red fly? What color wires do I solder on which pin of the connectors? Was there suppose to be any instructions that came with it, or the entire greenbull for that matter?

Currently our USB breakout board is only compatible with Planet-CNC software as it has to be registered with Planet-CNC.

Click the link to add information to this solution:
Hi, I have watched your vids on YouTube and I am interested in purchasing one of your USB Break-Out Boards. I currently own and use FlashCut CNC software, which is USB based, on all of my machines. I'm wondering if you could tell if the Flashcut software will talk with the USB Break-Out Board? Thank You

Hey, sorry I just found the wiring diagram and see that #4 is disabled. My bad. Thanks.

Click the link to add information to this solution:
I just purchased some wire for my 2.2 spindle as per your recommendation it's 14 AWG stranded wire for the VFD to Spindle (U, V, W) connections. However, it's a three wire (black, white and Ground). Which numbers on the female pin connector do I connect the wires to. Cheers.

Sure, let me check.

Additional Information:
Your order was shipped out on Tuesday (10/20/2020). I noticed that your email was not stored in the customer record when the order was made. I will send you the tracking number via email now.

Click the link to add information to this solution:
Placed an order for the cable set for the Pokeys57cnc interface on 10/20 but it is not showing up in My Account as being ordered. It was charged to my credit card and I have not had any info that it was received by you.

Currently we do not know the values of the electronic components inside our drivers, since these drivers are supplied by our manufacture and replaced by them if a manufacture defect is present.
Please email us at customerservice@buildyourcnc.com for more information on possible replacements.

Click the link to add information to this solution:
I recently had a mishap with one of my stepper drivers which resulted in a resistor being burned out. Would you be able to tell me what the resistance is for the R25 resistor inside the 6.0 amp driver?

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

The 8 wire motors need to be wired in bipolar parallel configuration. The wiring is as follows: Red and Blue to A+, Yellow and Black to A-, White and Brown to B+ and Orange and Green to B-. To find the wiring for the 4 wire motors, the wiring is Red to A+, Orange to A-, Blue to B+ and Green to B-.

Click the link to add information to this solution:
I have constructed the cnc router machine as shown in woodsmith magazine. I have purchased the 3 Nema stepper motors. The one larger motor has 4 wires, as do the other two. However, on the schematic, the Z, and Y axis motors indicate 8 wires each. Did I go wrong, or are there different Nema 23 motors?

Wiring diagrams for the Laser Power Supply will be mostly the same with the updated power supply. The main difference is the newer power supply contains a secondary green terminal block on the front of the power supply next where the hard leads are connected. This differs from the older power supply which had contact points on the back of the power supply. Please refer to the tutorials section for updated information and if you have specific questions please email techsupport@buildyourcnc.com

Click the link to add information to this solution:
I am assebling the Blacktooth CNC laser 20x24" with what appears to be an updated power supply. After refrencing the wiring diagram on line and the totorial, may I ask for an updated diagram or totorial, the current version do not appear to match match the configuration provided. I do not feel confidant in the educational guess, that I have. thanks

(These steps are to be taken with precaution, due to the fact that we do not know the model or manufacturers specifications for your BoB)

Here is a link to our CNC electronic videos(

Click the link to add information to this solution:
I have a CNC Machine from China, and the Breakout Board is not Labeled. Is there any way to test the board using Mach3 to find out the pin designations? db25 bob

There is a multitude of methods to create the table and frame for the greenBull long-z CNC machine, as some of the illustrations are shown on our gB webpage.

The image with the hollow mid section, is a custom table that will take advantage of the entire long-z axis assembly. So the frame can be built in that manner, however the CNC table should have its 3/4" table top. So you can cut standard sheets of wood, aluminum, plastics, etc.

So that specific illustration is not needed, however if you plan on cutting at that depth then it will defiantly benefit you to have that frame as shown in the illustration!

Click the link to add information to this solution:
Can you please clarify what a long Z axis table should look like? I've built a frame that matches the dimensions on the GreenBull page but under long Z it says a custom frame is required made out of steel, which I did. But do I need to have the frame open like shown in the picture or is that just showing what the table looks like under the 3/4 material?

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.