Yes, the blueChick kits are available. You can get the shipping rates automatically in the shopping cart. There will be a calculate shipping button on the enter shipping information section of the shopping cart.

Click the link to add information to this solution:
CAN YOU PLEASE TELL ME THE AVAILABILITY OF 12X36 BLUE CHICK 4.2, AND COST FOR SHIPPING TO ZIP 72802 IN RUSSELLVILLE, ARKANSAS?

Mounting the extruder to the whiteAnt can be done a couple of ways. One is to take the 4 mounting holes located at the lower portion of the z-axis rail support and use long screws protruding out. Take a thinner material and drill the four holes matching the locations of the 4 screws and screw on nuts to hold it in place. The other option would be to use the metal bracket and fasten to the edge of the rail support.

Click the link to add information to this solution:
CAN YOU GIVE ME SOME HELP OR POINT IN THE RIGHT DIRECTION TO INCORPORATE MK 7 EXTRUDER WITH BOOK PLANS FOR 3D PRINTER?

To convert the whiteAnt to a CNC machine, you will want to lower the upper structure to the lowest position to create the most rigidity overall. You will see that there are many holes below the sides of the upper structure that are evenly spaced. This is so you can adjust this lower. You will also want to fasten the lower sides to a substrate (piece of wood, or something) with l-brackets or something that has a bit of adjustment capability. This will keep the sides more rigid as well. Use a Dremel for the spindle. If you want to use a another spindle, let me know and we can product a mount for that spindle since the Dremel has poor runout (TIR). This is important if you are wanting really precise milling.

Click the link to add information to this solution:
how can I convert the whiteAnt from the 3D printer mode to the CNC milling mode?

Conceptually it is straightforward to predict the radiofrequency (RF) exposure intensity at any point in the vicinity of a cellular radio base station antenna. Simply multiply the effective radiation power times the inverse square of the distance times the relative gain of the antenna in the direction of the interest. The relative gain in different directions is know as the antenna radiation pattern and is usually available from the antenna manufacturer in graphical or tabular form.

Unfortunately, in real life the calculations involved in base station antenna evaluations are quite complex and require expert knowledge and experience to deal with the many parameters that are involved. An excellent reference summarizing this process is the Federal Communications Commission OET Bulletin No. 65 titled "Evaluating Compliance With FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields," available on the Federal Communications Commission (FCC) website.

To assess the RF hazards associated with handheld cell phones it is necessary to predict the rate of absorption in the body of radiofrequency energy, a parameter called the specific absorption rate (SAR). This is a very complex calculation, and cell phone manufacturers often rely on measurements of SAR in fluid-filled cylinders or plastic containers in the shape of a head. The FCC requires cell phone manufacturers to provide this data to FCC. You can obtain the data for your model phone on the the FCC's website. Unfortunately only cell phones manufactured in the last couple years are listed here.

As to your question about keeping RF exposures within the safety code, please read the other questions posted on this website this matter. Cellular radio products that meet FCC requirements will be within the guidelines established by safety standards organizations for users' and public exposure to RF radiation fields.

Gary H. Zeman, ScD, CHP

Click the link to add information to this solution:
FIRST OF ALL, THANKS FOR DESIGNING A WONDERFUL SITE. MY QUESTION IS: HOW DO YOU CALCULATE EME (ELECTROMAGNETIC EMISSIONS) AROUND THE TRANSMITTER (ANTENNA) AT ANY GIVEN POINT AND WHAT ARE MEASURES TO KEEP IT UNDER SAFETY CODE?

Your steps per inch will vary. I suggest watching my calibration video.

Click the link to add information to this solution:
I AM CURRENTLY HAVING SOME PROBLEM SQUARING THE GANTRY AND MY STEPS PER INCH ARE NOT 1422.22 ACCORDING TO YOUR CALCULATIONS IN AUTO SET UP THEY COME OUT LIKE 1416.#### THIS A BIG DEAL?

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

This will depend on the VFD you have to identify the correct terminal. The terminal on the VFD will be labeled AI1 typically (Analog Input #1). You will also need to make sure to complete the PWM circuit using the GND terminal on the VFD.

Additional Information:
I have wired my 0-10V signal to the AI1 and GND terminals as suggested. I have also set the PD-01 and PD-02 settings to 1. Still nothing. Is there something else that I am missing?

Additional Information:
Thanks for the information. Can you let me know the model of the VFD that you have?

Additional Information:
VFD Model # YL600-2S-2K20

Additional Information:
Thanks. I will check our resources and documentation to see if there is another programming setting that needs to be changed.

Additional Information:
Does your VFD have a VI terminal?

Additional Information:
No, it does not. The terminals for this VFD are as follows (seperated by dashes "-").

10V-AI1-AO2-PLC-DI5-DI3-DI1-COM
AI2-GND-AO1-DI6-DI4-DI2-FM-24V

Additional Information:
Do you have a PD070 parameter?

PD070 is the main Analog Input parameter.

The options for that parameter is:
0: 0-10V
1: 0-5V
2: 0-20mA
3: 4-20mA
4: 0-10V (4-20mA Stacked)
5: XIA
6: (VI+XIA)/2
7: (3VA+XIA)/4
8: (XIA_XIB)/2
9: Max (XIA, XIB)
10: Min (XIA, XIB)


Additional Information:
There is a PD-00 thru PD-09. PD-07 is currently set to 0.

Additional Information:
It appears that the manual I’m using “Titled YL600” is not the same as your unit. I will check our manuals and find the one that has only PD-00 to PD-09.

Additional Information:
For that VFD, the parameters are P0. The 0 may look like a D on the display.

The parameters that need to be changed for the AI1 to work (Brackets [] around the correct selection):

P0-01: First Motor Control Mode
- 0: Sensorless Vector Control
- 1: Flux Vector Control (FVC)
- [2]: V/F Control

P0-02: Options of Command Source
- 0: Operation Panel Command Channel (LED will be off)
- [1]: Terminal Command Channel (LED will be on)
- 2: Communication Command Channel (LED will flicker)

P0-03: Options of Principle Frequency Source X
- 0: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, no power-down memory)
- 1: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, with power-down memory)
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID (Proportional Integral Derivative Control)
- 9: Communication Given

P0-11: Upper Limit Frequency Source
- 0: P0-12 (Make sure the P0-12 parameter has the correct max frequency if used)
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given

P0-27: Command Source Bundle with Frequency Sources
Single Digit: Options of Operation Panel Command Bundle with Frequency Sources
- 0: No Bundling
- 1: Digital Setting Frequency
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID
- 9: Communication Given
Double Digit: Options of Terminal Command Bundle with Frequency Sources
Hundred Place: Options of Communication Command Bundle with Frequency Sources
Kilobit: Options of Automatic Operation Bundle with Frequency Sources

P2-09: Upper Limit Source of Lower Torque Under Speed Control Mode
- 0: Function Code P2-10 Setting
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given
- 6: MIN (Al1, Al2)
- 7: MAX (Al1, Al2)
- Maximum range for options 1-7, accords with P2-10

If you elect to use a different AI#, then configure the parameters (P0-03, P0-11, P0-27 and P2-09) accordingly.

Click the link to add information to this solution:
I'VE BUFFERED A PWM SIGNAL TO 0-10V ANALOG AND I WOULD LIKE USE THAT RUN YOUR 110V 2.2KW SPINDLE VFD. COULD YOU PLEASE DETAIL THE CORRECT WIRING VFD SETTINGS GET WORKING?

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN A PRINTER CABLE PORT AND USB MOTOR KITS

The overall size of the machine, really depends on both the area available to you and also the overall size of material being used. Now our larger machines (blackFoot, greenBull, greenLean) can cut all the materials mentioned above, and if equipped with our 2.2kW spindle you will be accurate up to ten thousandths of an inch.
Our greenBull machine does have an option for a long-z axis, that was especially designed to cut foam, but depending on the overall size it might not be a requirement for the specified request.

Click the link to add information to this solution:
I HAVE A SIGN SHOP AND WE NEED CUT ALUMINUM, PLEXIGASS, FOAM AND OTHER MATERIALS FOR SIGNS. CAN YOU TELL ME WHAT MACHINE WE NEED? I LOOKING 4'X8' OR 5' X 10'

Roller chain in general is adjustable by using "master links", which are links which have horseshoe clip holding the pin and thus allow connections to be made or broken. The #25 is a designation of the type of roller chain. ANSI codes designate that the first digit(s) specify the pitch in eights of an inch, and the last digit is 0 for standard chain, 1 for lightweight chain, and 5 for bushed chain with no rollers. So #25 is 2/8 = 1/4 inch pitch bushed chain with no rollers.

Click the link to add information to this solution:
IS THE "#25 ROLLER CHAIN" ADJUSTABLE TO ANY LENGTH? LIKE IF I ORDERED TEN FEET OF IT, CAN MAKE TWO 3-FOOT LOOPS AND ONE 4-FOOT LOOP USING SOME SORT CHAIN JOINER?

The following answer assumes "radio Base Station Antennas" refers to base stations used for personal wireless communications services such as cellular telephone, Personnel Communications Services (PCS), and Enhanced Specialized Mobile radio (ESMR). In the United States, the frequency band allocated for base stations used for personal wireless communications is 869-894 MHz for cellular service, 851-866 MHz for ESMR, and 1930-1990 MHz for PCS. The IEEE exposure limits (maximum permissible exposure—MPE) for occupational exposure (controlled environments where exposures may be incurred by persons who are aware of the potential for exposure) are frequency dependent and are expressed in terms of incident power density. The appropriate value to compare with the MPE is the incident power density averaged over the vertical cross-section of the human body. The occupational exposure limits are also time-averaged over any six-minute interval. The IEEE C95.1-1991 MPE values are shown in the table below:
IEEE C95.1-1991 Maximum Permissible Exposure (MPE) Values
Frequency Band Power Density
General mw/cm2 W/cm2
851-866 MHz f/300 mW/cm2 2.84-2.88 28.4-28.8
869-894 MHz f/300 mW/cm2 2.90-2.98 29.0-29.8
1930-1990 MHz f/300 mW/cm2 6.43-6.63 64.3-66.3
NOTE: f is in MHz
As indicated above, these values are for continuous exposure (t > 6 minutes) and are to be compared with the spatial average of the incident power density. all base stations used for personal wireless telecommunications services in the United States are required to comply with the FCC limits (as mandated by the Telecommunications Act of 1996). The FCC limits are based on a hybrid of the IEEE limits and the 1986 recommendations of the National Council on Radiation Protection and Measurements. The FCC MPEs are the same as the IEEE values for frequencies below 1500 MHz but are capped at 5 mW/cm2 (50 W/cm2) for frequencies greater than 1500 MHz.

Both the FCC and IEEE MPEs for exposure of the public (uncontrolled environments) are one-fifth of the above values. As above, the value to compare with the MPE is the incident power density averaged over the vertical cross-section of the human body. The averaging time for the general public is 30 minutes. Thus, for transient exposures lasting six minutes or less, the MPEs for occupational exposure and exposure of the general public MPEs are the same. For cases of simultaneous exposure from antennas operating in different frequency bands, the ratio of the spatially averaged incident power density in each frequency band to the corresponding MPE for that band is determined and the sum of all such ratios must be less than unity in order to comply.

R. C. Petersen
Manager, Wireless and Optical
Technologies Safety Department

Click the link to add information to this solution:
WHAT ARE CURRENT RECOMMENDED IEEE EMF OCCUPATIONAL EXPOSURE LEVELS AND GUIDELINES FOR RADIO BASE STATION ANTENNAS?

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

Everyone always assumes they are doing something wrong when a plant fails to perform to their expectations. Grapes need pollinator activity to set viable fruit, but there is a shortage of bee activity throughout the country. When the flower cannot be pollinated by bees, the resulting fruit usually atrophies. It is not your fault, just a shortcoming in nature's network.

Click the link to add information to this solution:
I PLANTED SEVERAL CONCORD GRAPE VINES DURING THE PAST FEW YEARS. GOT A COUPLE OF VERY TINY BUDS THIS YEAR, BUT THEY DRIED UP AND DIED. WHAT AM DOING WRONG?

Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

Additional Information:

Click the link to add information to this solution:
WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

Click the link to add information to this solution:
I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

It is never too early to begin planning for the coming fall's influenza vaccination program. The most important thing you can do initially is to place your order for vaccine from your usual source. Some manufacturers often stop taking pre-orders in mid-May. Be sure to include vaccine for pediatric patients needing two doses and also for your facility's healthcare workers as part of your overall campaign.

Click the link to add information to this solution:
WE ARE ALWAYS CONCERNED THAT THERE WON'T BE ENOUGH VACCINE TO VACCINATE OUR PATIENTS IN THE FALL. WHAT CAN DO ASSURED WE'VE DONE ALL POSSIBLY AVOID THIS TYPE OF SITUATION?

The electronics can be tricky sometimes, especially if more than one change is made for a test. You can move the x-dir wire to another pin and set it in the software configuration. If it works, then only that pin is bad.

Click the link to add information to this solution:
ON THE BOB...EVERYTHING TESTS OK BOB EXCEPT X-DIRECTION OUT. IT'S VOLTAGE IS SLIGHTLY DIFFERENT THAN Y AND Z (5.00 INSTEAD OF 5.03. TESTED X DIRECTION ALL THREE DRIVERS. IN EACH CASE THERE GOING INTO DRIVER BUT NOT OUT IT.

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?