it is possible to install 2 motors on a single axis but you will require another driver and motor, but wire it directly to the same pins on your breakout board. Also the orientation of your motor since it is opposite side of the original so getting it to move accordingly to the original motor it will need to be orientated correctly. The slight shift could be the cause of the rod not being completely flat where the set screws are suppose to tighten the sprocket to the rod, so sanding it to a flatter surface might fix the shift in directions.
Currently do not have a kit or schematic available.

Click the link to add information to this solution:
I am interested in your Black Toe (24" X 48") machine, and am wondering if using two medium motors on the "X" and "Y" axis makes sense relative to power and alignment (racking). What would you recommend?

What is the item that you purchased on Sept 24?

Click the link to add information to this solution:
Hi my name is Robert and I have try to contact you on a purchase from you around 24 sept and i have not received it so i tried calling you via 281-815-7701 and talked to many other person except you . 9am to 5pm Could you Please send a Phone number that work please.

Yes, I can furnish the redFly system without motors. You can request a quote for this at customerservice@buildlyourcnc.com

Click the link to add information to this solution:
[422] I'm interested in using Mach4 and already have 3 motors (425 oz-in). Is it possible to get a electronics system without the motors?

The blackTooth machine, as it is designed cannot be modified easily as the box within which it is contained also serve as its structure. We are currently designing a special mount for the greenBull (for the 40 watt tube) which will provide 5'x10' or 6'x12' work area and the machine is far less expensive than comparable 4'x8' laser systems. We are also developing a 4'x8' 80 watt system where the tube is in the horizontal orientation. More information can be found in the R&D section.

Click the link to add information to this solution:
I am interested in getting your 40W laser system. How difficult will it be to increase the size to 48" x 48"?

If you are using Mach3 do you have your hotkeys set up correctly?

Additional Information:
The office was closed on the weekends and during Dr. Martin Luther King Jr. Holiday.

Click the link to add information to this solution:
I got my Blackfoot 4.3 built. Hooked it to the Redleaf and when testing the axis controls Im able to move the X axis using the Right arrow key, but unable to move it with the left key. I have no control on my Y axis. Tried calling for tech support and recieve voicemail 2 days in a row after a few calls each day.

Yes, we can make a redLeaf system that has all 6A drivers for use with the 651 oz-in motors. We can also wire the electronics in a way that two of the drivers will use the pins of the same axis so that axis will drive two drivers and motors.

Click the link to add information to this solution:
I am building a machine that requires 2 steppers to drive the Y axis, can you make me a redleaf system using the 651oz steppers that will work for me?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

If you are using Mach3, the setting for the input pin 10 may be enabled as a default for use with the Emergency Stop. If there is no emergency stop on that pin, the reset will trip every time.

Click the link to add information to this solution:
I have the redleaf system for my black toe machine I have wired my limit switches in series NC after setting up in mach 3 I still get limit switch tripped after apply and ok setup can only run if I disable what am I doing wrong

Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Additional Information:
Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Click the link to add information to this solution:
I'm interested in getting the CO2 laser & Spindle for my Blackfoot - I currently have just the router mount. Do you sell complete kits or can you advise on what I need? Thank you

Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens, and nozzle. You will also need some mechanical parts and some motors, drivers, and power supplies for the drivers and the controller.

Click the link to add information to this solution:
I'm interested in getting the CO2 laser & Spindle for my Blackfoot - I currently have just the router mount. Do you sell complete kits or can you advise on what I need? Thank you

We attempt to provide as many services as possible to fit the needs of the CNC community. For a quote on a custom job, please email customerservice@buildyourcnc.com and we will be happy to assist you.

Click the link to add information to this solution:
I bought longs motor nema 34 stepper motor with 4 powers supply and dm860 from ebay, would you be interested in doing all the wiring for me? I pay you for you time

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

The bluchick CNC router is a perfect small format CNC that can handle most jobs. Please check here to see the latest information on this CNC router. blueChick CNC Machine. The machine can be purchased assembled. Al you will need is a computer and spindle.

Click the link to add information to this solution:
I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

Yes, we offer a CNC electronics assembled package called the redFly, redLead and redSprout. If you already have a computer, I would recommend the redFly. You would still need to add connectors to the ends of your motor cable.

https://www.buildyourcnc.com/item/cnc-computer-system-redFly

Click the link to add information to this solution:
I need to replace the fried electronics box for my 6090 wood router. Do you offer a play and play, no wiring required, kit? If yes, how much? If no, can you recommend one?

At this time we are in the process of developing a UK distributor. Stay tuned for details.

Click the link to add information to this solution:
Hi! I am interested in the blacktooth Kit. I live in UK. Is there any possibility of decrease the price of the shipment or do you know maybe an UK based kit provider? Thanks.

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I am interested in the 3 axis combo USB option. I notice you endorse the Planet-CNC for use with this but will Mach3 interface well with the USB beak out Board?

To order the system, just go to this page:
http://www.buildyourcnc.com/category/cnc-computer

Make sure to also order the 4 conductor cable that you will need for the connections between the motors and the drivers. This length will depend on your machine, where the motors will be attached, and where you plan on setting the computer system.
The cable can be found here:
http://buildyourcnc.com/item/electronicsAndMotors-cable-wire-20awg-wrcon

If you want to use Windows, you will also need to purchase that on the first link I provided. If not, we will install Linux with EMC2 and linuxcnc

Click the link to add information to this solution:
How do I go about ordering the redLeaf or redSprout computer cnc system?

When we receive an email pertaining to shipped product issues, they are forwarded to our shipping department. If you do not receive a response, for any reason, please contact us again by email, and/or give us a call at 281-815-7701

Additional Information:
20

Click the link to add information to this solution:
Hi, I received a laser tube last week, and it was brokken in the packet. I tried to write to customer service but no answer so far. How do you handle this? The packet was not dammaged in any way. I was only able to see it was broken when it was complete unpacked.

The 2.2kW Spindle has many advantages over a standard router such as the Porter Cable. The most obvious benefit to the user is the significant reduction of both dust and noise.

Additional Information:


Additional Information:
What size water source is needed and how long can it be used before it is too warm? Do you have a pressure vs. flow curve for the spindle so I can properly size the water pump?

Additional Information:
I used a small pond pump inside a 5 gallon bucket. I put a little bit of windshield washer fluid in with it to keep anything from growing in it. It's worked great. I've had 1 hour run times with no noticeable increase in spindle temp.

Additional Information:

Click the link to add information to this solution:
I am interested in buying the 2.2 kW spindle. Does it run much quieter than a 2 hp Porter Cable router? You also mention a pump with a bucket of water. How long until the water is too warm to cool the spindle?