CNC Questions And Answers

I bought the book that you co-authored (Build Y...

I bought the book that you co-authored (Build Your own CNC) a few years ago. Its not till now that I’ll be able to start the project. Are all the...

I bought the book that you co-authored (Build Y...

I bought the book that you co-authored (Build Your own CNC) a few years ago. Its not till now that I’ll be able to start the project. Are all the...

I am in Houston. I will use this to make cabine...

I am in Houston. I will use this to make cabinets. Do you have a location I could see one in use cutting similar products?

I am in Houston. I will use this to make cabine...

I am in Houston. I will use this to make cabinets. Do you have a location I could see one in use cutting similar products?

Can anyone tell my the exact center to center m...

Can anyone tell my the exact center to center mounting hole distance on the 20mm linear guide rails? I have done some measuring but I am afraid they vary.

Can anyone tell my the exact center to center m...

Can anyone tell my the exact center to center mounting hole distance on the 20mm linear guide rails? I have done some measuring but I am afraid they vary.

How to display RPM instead of frequency on the ...

How to display RPM instead of frequency on the VFD? I have the 2.2kv 110 volt spindle and inverter.

How to display RPM instead of frequency on the ...

How to display RPM instead of frequency on the VFD? I have the 2.2kv 110 volt spindle and inverter.

How do you set up Frequency converter for 2.2kw...

How do you set up Frequency converter for 2.2kw spindle?

How do you set up Frequency converter for 2.2kw...

How do you set up Frequency converter for 2.2kw spindle?

Is there a recommended break in process for a 2...

Is there a recommended break in process for a 2.2kw water cooled spindle?

Is there a recommended break in process for a 2...

Is there a recommended break in process for a 2.2kw water cooled spindle?

how to conect the VFD spindle using modbus

I've been unable to cut through acrylic or wood...

I've been unable to cut through acrylic or wood at a thickness of 1/8" or less with the BlackTooth. Even with multiple passes (x10) and full power, a clean cut...

I've been unable to cut through acrylic or wood...

I've been unable to cut through acrylic or wood at a thickness of 1/8" or less with the BlackTooth. Even with multiple passes (x10) and full power, a clean cut...

Can you tell me the correct way to wire tool pr...

Can you tell me the correct way to wire tool probe on your Mach3 USB board?

Can you tell me the correct way to wire tool pr...

Can you tell me the correct way to wire tool probe on your Mach3 USB board?

spindle vfd error codes

what are the vfd spindle error codes

spindle error codes

Hi i'm looking to upgrade my rail system along ...

Hi i'm looking to upgrade my rail system along my X-axis which is 10 ft. Im wondering what it takes or if it is even possible to join two HIWIN...

Hi i'm looking to upgrade my rail system along ...

Hi i'm looking to upgrade my rail system along my X-axis which is 10 ft. Im wondering what it takes or if it is even possible to join two HIWIN...

Are you open today? I tried calling twice with ...

Are you open today? I tried calling twice with no answer.

Are you open today? I tried calling twice with ...

Are you open today? I tried calling twice with no answer.

Is there a way to use Mach4 to control my VFD?

My X-axis on the Blacktoe cannot run above ~40 ...

My X-axis on the Blacktoe cannot run above ~40 ipm. I've checked all connections,tensions, sprocket locks, etc. All is fine. Can the 425 OZ stepping motor be replaced with a...

My X-axis on the Blacktoe cannot run above ~40 ...

My X-axis on the Blacktoe cannot run above ~40 ipm. I've checked all connections,tensions, sprocket locks, etc. All is fine. Can the 425 OZ stepping motor be replaced with a...

I have been using a Blacktooth for some time, w...

I have been using a Blacktooth for some time, with Vectric2d and Mach3. I have always found that the laser burns a hole before moving off. I have always set...

I have been using a Blacktooth for some time, w...

I have been using a Blacktooth for some time, with Vectric2d and Mach3. I have always found that the laser burns a hole before moving off. I have always set...

I have a blue brew break-out board. Do I use a ...

I have a blue brew break-out board. Do I use a seprate power supply for it and what amp output should it have if used.

I have a blue brew break-out board. Do I use a ...

I have a blue brew break-out board. Do I use a seprate power supply for it and what amp output should it have if used.

SIGNAL AND 5V POWER WIRING DIAGRAM FOR RELAY US...

SIGNAL AND 5V POWER WIRING DIAGRAM FOR RELAY USB BR ABOUT BOARD.

SIGNAL AND 5V POWER WIRING DIAGRAM FOR RELAY US...

SIGNAL AND 5V POWER WIRING DIAGRAM FOR RELAY USB BR ABOUT BOARD.

I would like some longer HIWIN rails and ballsc...

I would like some longer HIWIN rails and ballscrews for my x-axis, 9 feet or 108 inches. You list maximums as 78 inches.

I would like some longer HIWIN rails and ballsc...

I would like some longer HIWIN rails and ballscrews for my x-axis, 9 feet or 108 inches. You list maximums as 78 inches.

Do you sell 1000mm long 40W laser tubes?

DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE B...

DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE B...

DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

Have a CNC routher that uses the Porter Cable 7...

Have a CNC routher that uses the Porter Cable 78125 considering 2.2kw spindle and controller do you have any mounts and our recommenadtions?

Have a CNC routher that uses the Porter Cable 7...

Have a CNC routher that uses the Porter Cable 78125 considering 2.2kw spindle and controller do you have any mounts and our recommenadtions?

Does the laser XL have air assist?

Country/region

CNC Questions And Answers