You can find a wiring diagram here:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

The CP terminal is wired to the step terminal on the 8825 step driver.
The CW terminal is wired to the direction terminal on the 8825 step driver.
The GND terminal connects to the GND on the 8825 step driver

The 5V connector on the driver simply powers the logic side of the chip and needs to connect to VCC pin on the keyboard jog.

Customer Response:
Thanks! Working now.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

The use of the hex inverter in the application to invert a direction signal to have a motor run in the reverse directions is relatively simple.

First, go to this link and look at the chip diagram:
https://www.buildyourcnc.com/item/electronicsAndMotors-hex-inverter-breakout-newbiehack-integrated_circuits-hex-inverter

Connect 5V from the USB interface tothe VCC pin. The pin on the keyboard jog header can be used. Connect the GND pin from the USB interface to the GND pin on the hex inverter. Connect the CW terminal from the USB interface to the 1A pin on the hex inverter. Connect the 1Y pin from the hex inverter to the driver.

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Click the link to add information to this solution:
Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

You will need a USB cable to connect the computer and the Mach3 USB. The 64-bit operating system must be Windows and you will need the Mach3 CNC control software installed on the operating system.

You will need to install the USB driver called RNRMotion.dll. You can find the driver here: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Move the file to your Mach3 Plugins folder Example: "C:/Users/ProgramFiles/Mach3/Plugins"

Mach3 will prompt you to select a driver and this is where you can select the "RnRMotionController" and check "Don't ask me again". This will allow your board to communicate with Mach3.

You will also need the xml file found on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

On that page, you will need to download the XML Mach3 Config File by right clicking on the link and selecting "save as". Save the Mach3Mill.xml file in your Mach3 root folder.

That file is the main configuration file for the Mach3 board. It has all of the typical settings that the Mach3 board needs.

Click the link to add information to this solution:
I have a 64 bit operating system and the Mach3 usb control board. What do i need to communicate between the two?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am installing a mach 3 usb controller into a wright cnc plasma table and I need instruction on wiring the thc (proma compact ) torch height controller to this board. IE will this board work to replace the parallel port board with usb controller board?

If you read the description the first uses a parallel interface for computer hookup. The second uses USB interface for computer hookup. The third utilizes an integrated computer which is built into the package thus you do not need an external computer.

Click the link to add information to this solution:
What is the difference between the 3 Blacktooth laser packages offered? Specifically, one with/without a computer? Why do I need one? Also, is the $2100 assembled vs the $1700 which is not? What am I paying $400 more for?

We recommend checking the dip switch settings on your drivers, having the correct microstepping/amp settings along with the steps/unit will help the motors run as effective as possible.
This is a default parameter that we use while we test our motors:
Driver dip switch settings will be at a 1/16 microstepping and 2.7amp (11001100) for x/y-axis and the z-axis will be at 1/4 microstepping and 2.7amp (10101100).

In planet-cnc with increasing the motor speed, you will have to modify the settings in planet-cnc (File/settings/setup) you will modify the initial speed, maximum speed, and the acceleration.
X/Y-axis step/unit: 1422.22 initial speed:500 maximum speed:750 acceleration:25
Z-axis step/unit: 1600 initial speed:100 maximum speed:300 acceleration:25
The initial speed and maximum speed will have to be roughly tested and adjusted per application.
Make sure to adjust the JOG slide bard underneath the axis controls on screen to about 750, to compensate for your x/y-axis adjustments. If left alone the speed will max out at the default setting.

Here is a video tutorial to calculate the steps required depending on your mechanical linear motion components. (

Click the link to add information to this solution:
I bought Nema 24 motors and driver package with usb board. What do i need to have more speed? Cant even jog past 25 ipm without the motor stalling (not having enough torgue)

The Mach3 USB controller can only output pulses and direction signals (5V logic signals).

To connect your Mach3 USB controller RNR controller with a servo AC that has a 24V open collector, you will need to use a level shifter circuit to convert the 5V pulses from the controller to 24V pulses that the servo can accept.

One way to do this is to use a simple transistor-based level shifter circuit. Here are the steps to connect your Mach3 USB controller RNR controller with a servo AC using a level shifter circuit:

Connect the 5V output signals from the Mach3 USB controller RNR controller to the base of the NPN transistor in the level shifter circuit.

Connect the collector of the NPN transistor to the 24V power supply.

Connect the open collector output of the servo AC to the emitter of the NPN transistor.

Finally, connect the ground of the Mach3 USB controller RNR controller and the servo AC to the ground of the 24V power supply.

The level shifter circuit will act as a switch, allowing the 24V power to flow to the servo AC when the 5V signal from the controller is present.

Remember that the MAch3 USB controller only outputs pulses for steps per rotation of a motor. If the servo requires a different method of motor rotation, this will not work.

Click the link to add information to this solution:
[575] Hello. I have rnr controller. My problem is connection with servo ac. My servopack have logic Voltage 24v open collector. How Connect and what i need to Connect rnr with servo if rnr have 5v logic. Thx

To control a spindle using the USB CNC interface, you will need a relay board that contains a transistor that can activate the relay with a power source with enough current that can activate the relay. This video explains all of the information you will need to develop this relay circuit:

Click the link to add information to this solution:
i have a breakout usb controller iam using a spindle output to active a relay 5V but it didnt work.... whats the problem, what else i need to active that realy 5v 10A?

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

Click the link to add information to this solution:
I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

Click the link to add information to this solution:
I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

You can find the wiring diagram for the Mach3 USB card on its product page here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Here is a direct link to the diagram:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

Click the link to add information to this solution:
I need wiring diagram for motor to driver to usb motion card. I cannot find diagram. I have been unable to get information for a week.

The datasheet for the parallel breakout board is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The datasheet for the USB interface is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/


Additional Information:
20

Click the link to add information to this solution:
I need wiring instructions for the breakout board you sent yesterday. It is not like the one in the videos and I don't know where to connect the 5V. No data sheet or anything.