CNC Questions And Answers

I installed a pokeys57cnc and use Mach3 for the...

I installed a pokeys57cnc and use Mach3 for the mill. When I page up or down the Z axis moves down. Is there a setting I need to change? I...

I installed a pokeys57cnc and use Mach3 for the...

I installed a pokeys57cnc and use Mach3 for the mill. When I page up or down the Z axis moves down. Is there a setting I need to change? I...

[365] I had ordered 3 and they appear to be lef...

[365] I had ordered 3 and they appear to be left handed threads. I did not see a specification when ordering. Is this mentioned somewhere?

[365] I had ordered 3 and they appear to be lef...

[365] I had ordered 3 and they appear to be left handed threads. I did not see a specification when ordering. Is this mentioned somewhere?

I have USB Interface board. All axes are workin...

I have USB Interface board. All axes are working if using MDI , using program some of the axes are only moving one direction. Example using Gcode X50 Y50 Z50...

I have USB Interface board. All axes are workin...

I have USB Interface board. All axes are working if using MDI , using program some of the axes are only moving one direction. Example using Gcode X50 Y50 Z50...

[541] I need some help, can I pay you for your ...

[541] I need some help, can I pay you for your time? I have a old Golden Laser has 2 co2 lasers 80 watts each, trying to put a new...

[541] I need some help, can I pay you for your ...

[541] I need some help, can I pay you for your time? I have a old Golden Laser has 2 co2 lasers 80 watts each, trying to put a new...

[73] Are there instructions that come with CAMBAM

[788] Does it make a difference if I use a PNP...

[788] Does it make a difference if I use a PNP instead of an NPN?

[788] Does it make a difference if I use a PNP...

[788] Does it make a difference if I use a PNP instead of an NPN?

[575] Why is a second PSU necessary for the lim...

[575] Why is a second PSU necessary for the limit switch and e-stop ?

[575] Why is a second PSU necessary for the lim...

[575] Why is a second PSU necessary for the limit switch and e-stop ?

[575] After reset of E stop, I get error messag...

[575] After reset of E stop, I get error message "RnR Motion Card Not Found". Have you any advice?

[575] After reset of E stop, I get error messag...

[575] After reset of E stop, I get error message "RnR Motion Card Not Found". Have you any advice?

Is there a way to change the direction of a mot...

Is there a way to change the direction of a motor with the motor to driver wiring?

Is there a way to change the direction of a mot...

Is there a way to change the direction of a motor with the motor to driver wiring?

[51] Would the single 8.8A power supply be unde...

[51] Would the single 8.8A power supply be undersized for 3 6.0A Drivers? would you recommend getting another PS?

[51] Would the single 8.8A power supply be unde...

[51] Would the single 8.8A power supply be undersized for 3 6.0A Drivers? would you recommend getting another PS?

Laser cutter won't cut

What is the correct pin and port setting for au...

What is the correct pin and port setting for auto tool zero on the Mach3 USB interface board. the auto tool macro works but does not stop lowering the bit...

What is the correct pin and port setting for au...

What is the correct pin and port setting for auto tool zero on the Mach3 USB interface board. the auto tool macro works but does not stop lowering the bit...

[104] What is the bore size?

[575] I have an older CNC (2018) which has been...

[575] I have an older CNC (2018) which has been working fine. The Windows 7 PC crashed and I am trying to get operational again using a windows 10 machine....

[575] I have an older CNC (2018) which has been...

[575] I have an older CNC (2018) which has been working fine. The Windows 7 PC crashed and I am trying to get operational again using a windows 10 machine....

[575] Is it possible to run board on usb power

[48] This kit came with DM542 driver what are t...

[48] This kit came with DM542 driver what are the dip switch settings for this with the usb interface

[48] This kit came with DM542 driver what are t...

[48] This kit came with DM542 driver what are the dip switch settings for this with the usb interface

I'm hooking up the VFD Controller to the USB co...

I'm hooking up the VFD Controller to the USB controller to control the speed of the spindle. In your video you have the wire from the USB controller to the...

I'm hooking up the VFD Controller to the USB co...

I'm hooking up the VFD Controller to the USB controller to control the speed of the spindle. In your video you have the wire from the USB controller to the...