You can connect the 5V from the Mach3 USB controller to the 5V terminal on the driver, the XP to the Step terminal on the driver and the XD to the Dir terminal on the driver.

Click the link to add information to this solution:
[575] I have motor control boards that have 4 pin input ( Step, Dir, EN, +5V) how do I connect this USB board?

This controller does not have an encoder input to determine the speed of a lathe spindle. The Pokeys57CNC does have an available encoder input.
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[575] how do i connect a lathe spindle speed encoder to this usb breakout board controller so i can set up for thread cutting on my lathe and on the mill for threading

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I have your mach3 USB BoB, do you guys sell a torch control relay I can wire up to turn my plasma torch on and off and how I would wife that too this BoB?

From the USB controller, the CP+ and CW+ are connected to the 5V terminal. The CP- is connected to the CP terminal of the driver and the CW- is connected to the CW terminal of the driver.

Additional Information:

Click the link to add information to this solution:
Please explain how to connect 2.5AMP stepper motor driver to USB board. All parts are from your store. Thanks

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"

Controlling a 3-axis or 4-axis motor configuration, you will need the following items drivers/motors/controller. Our electronics combo comes with the items mentioned and with power supply/miscellaneous items.
The only other item needed will be a computer (with controller software) to communicate and view controls of your motors.
Using the Parallel breakout board will use Mach 3 software, and USB will use Planet-CNC software.

Additional Information:
You can use this link to see the videos on how to connect the electronics together and make them work: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
hey, where can i see the steps how can i control 3 or 4 step motor? can i use the Axis Electronics Combo? or i need to connect controller?

You will need a USB cable to connect the computer and the Mach3 USB. The 64-bit operating system must be Windows and you will need the Mach3 CNC control software installed on the operating system.

You will need to install the USB driver called RNRMotion.dll. You can find the driver here: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Move the file to your Mach3 Plugins folder Example: "C:/Users/ProgramFiles/Mach3/Plugins"

Mach3 will prompt you to select a driver and this is where you can select the "RnRMotionController" and check "Don't ask me again". This will allow your board to communicate with Mach3.

You will also need the xml file found on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

On that page, you will need to download the XML Mach3 Config File by right clicking on the link and selecting "save as". Save the Mach3Mill.xml file in your Mach3 root folder.

That file is the main configuration file for the Mach3 board. It has all of the typical settings that the Mach3 board needs.

Click the link to add information to this solution:
I have a 64 bit operating system and the Mach3 usb control board. What do i need to communicate between the two?

You should not have a problem with using this controller and having more than 500 lines of GCode. The 500-lines limitation is specific to licensing. Make sure that the Mach3 that you are using does not show "Demo" at the top of the screen. You can also confirm this in the help->about. If you are using a license that was purchased through this website, or from Machsupport.com, you should be fine.

Additional Information:
i have a licence but mach 3 not work above the 500 lines

Click the link to add information to this solution:
[575] Although i have licensed mach, when i use that particular board it seems to run only 500 lines of code, how can i fix that? i

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
Hey ! I have purchased a VFD with matching spindle 1.5kW and control program UCCNC. And my interface card is DB25, the question is how do I connect the VFD to DB25 so that I can control the speed with UCCNC? Sincerely "cnc beginners"

Yes, that driver has standard step and direction signal terminals that will work fine with the Mach3 USB controller.

Click the link to add information to this solution:
[575] We have Gecko 203V that require 5v input signal, can this be done?

I do not recommend using the Mach3 USB controller to be used with a torch height controller. There are only 4 inputs on the Mach3 USB controller. We have tried to interface a Proma THC to this board without success; however, we did not exhaust all possibilities.

I would recommend the Pokeys57CNC controller to connect the Proma THC as I have interfaced these two before and they work well together.
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[575] Hello. Does this USB interface board thc? I have the proma 150.

If the motor has 8 wires, you will need to wire the stepper motor in bipolar parallel. This motor (425 oz-in) is wired as follows:

Red and Blue wires to A+ on driver
Yellow and Black wires to A- on driver
White and Brown wires to B+ on driver
Orange and Green wires to B- on driver

Click the link to add information to this solution:
[54] There are 8 wires on this motor. How do you connect to the driver?

When you plug the USB controller into the computer using a USB cable, and the planet-cnc software is running, you will be presented with a dialog box that will contain a text box for the key that you received from the planet-cnc folks.

Additional Information:


Additional Information:
Is there any other software that will work with your controller Mach3? Thanks for the help!

Click the link to add information to this solution:
However it how do I get the software to work? PlanetCNC sent me a key that looks like it will only work with a backup control board I purchased from them?

The parallel breakout board has the db25 connector for data and the USB connector for power. Connect the USB from the computer to the parallel breakout board so the breakout board will have 5V of power coming from the computer. The db25 connector (connector with the 25 pins) receive data signals for each pin from 1 to 17 and have respective numbered screw terminals, some for input and some for output (18 to 25 are gnd pins).

Click the link to add information to this solution:
Should I connect both the USB and the 25 pin connector of the parallel breakout board to the computer?

You can use this board to have two motors/drivers on a single axis.

You have two solutions for this:

Wire the YP and TD to two drivers so they are receiving the same pulses and direction signals from the controller (if you need the motors to turn in opposite directions, just swap the A and B coils where the motor connects to the driver for one of the drivers/motors). This will free up an axis on the board.

Use the Mach3 slaave axis option where you resolve the two motors on a single axis by software. This will require you to use the extra axis on the board.

Click the link to add information to this solution:
[575] Can this board drive two (2) Y-motors? Design uses 1 X, 2 Y, and 1 Z motor. The schematic has X, Y, Z

The female connector (https://buildyourcnc.com/item/electronicsandmotors-connector-round-female-4pin) contains 4 terminals on the back of the connector to which the wires can easily be soldered.

Click the link to add information to this solution:
4 Pin Round Female Connector - Hi, I wish to buy this but not sure how to connect this to a cable, please help

There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

Click the link to add information to this solution:
I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?