You can use our shopping cart to determine the shipping. Add the machine and the parts you want to purchase, enter your shipping address and click on the Calculate Shipping Button to get a price for shipping. The shipping charges are determined directly from the carriers at the time of pressing that button.

Additional Information:


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi i am interested in the greenBull 6x with Hybrid Laser/Spindle Head (includes Spindle/VFD and Laser Components) - USB Interface (Long Z). I was wondering how much it would cost to get this machine to NZ?

If you already have a Mach3 license, you don't need to purchase another one. The license is connected to you rather than the computer. Mach4 is licensed to the computer, but you are able to have multiple computers for each license, and can be switched from one computer to another.

If you purchased the license from me, you can call (make sure to leave a voicemail), or email to get a re-issued license.

Click the link to add information to this solution:
[575] I have an older CNC (2018) which has been working fine. The Windows 7 PC crashed and I am trying to get operational again using a windows 10 machine. I will have to buy a new license for the Mach 3 so will need to get the interface board I have to talk to MAch 3. Can I get just the disc or is there a place I can download what I need?

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

The Mach3 USB interface board will require a 24V power supply to enable the use of the input, output terminals, and the spindle VFD 0-10V and output for speed control.

Click the link to add information to this solution:
Hi Patrick right now I have a parallel port cnc machine that I built in 2013 using the hardware and components I purchased from your website. I want to update my system by changing my current parallel port interface board to a Mach3 USB interface board from your website. Is the Mach3 USB interface board all I need to do this or is there other components I need to get. please advise.

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?

Sure, the USB interface has a place for 4 axes of limit switches.

Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

Let me know if this information was helpful (or not) by adding information to this question. Thanks.

User response:
Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
Thank you.

buildyourcnc response:
On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

Click the link to add information to this solution:
I have nearly completed the CNC machine from the book, but I am using it with a USB breakout board, and have no idea how to wire the 6 limit switches to the board. I'm having difficulty following the diagram on the USB breakout board screen. Can someone please help me?

PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
can you please clarify exactly what I receive w/ 5' x 10' CNC machine kit and what additional items I would need to have a fully operational machine?

PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
what I receive w/ 5' x 10' CNC machine kit and what additional items I would need to have a fully operational machine?

Decreasing the speed of acceleration in the cutter? Meaning of your router/spindle?, To modify the speed of a router will be going to the router itself and modifying the speed, but if a spindle is being used modifying it will be done either manually in the VFD (VFD Setup:
Change PD001 to '0' (source of run commands)
Change PD003 to 300 (main frequency - Hz)
Change PD004 to 300 (base frequency - Hz)
Change PD005 to 400 (max operating frequency - Hz)
Change PD006 to 2.5 (intermediate frequency - Hz)
Change PD008 to 220 (max voltage - V)
Change PD009 to 15 (intermediate voltage - V)
Change PD010 to 8 (minimum voltage - V)
Change PD011 to 100 (frequency lower limit - Hz)
Change PD142 to 7 (rated motor current - Amps)
Change PD143 to 2 (motor pole number)
Change PD144 to 3000 (rated motor revolution))<- make sure these are your settings in the VFD. If the spindle is wired to the breakout board and is working through Mach 3 then the modification will be done in your CamBam/Feed rate settings.

Click the link to add information to this solution:
How can I decrease the rapid acceleration of the cutter from a completed cutting operation to a new location so that the stepper motor will not lose its steps and mess up the machine zero settings? I am using CamBam and Mach3 on my machine with a chain drive. what is the best way to reduce accleration

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

You can do raster and vector engraving on the greenBull laser/spindle combination. The methods of this process is not accomplished in the same way as the typical laser machines where CorelDRAW is used. The Mach3 laser plug-in can be used for the raster engraving and standard CNC g-code can be used for vector cutting and engraving.

The raster method will not be fast on the greenBull since the z-axis is heavy and there are inertial limitation on doing fast raster back and forth movement. Vector is the best use of this machine.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am looking at purchasing the greenbull 5X system with the laser/spindle combination. Can the laser do both rastered engraving as well as vectored cutting with the same breakout board and software? If I have this wrong please let me know what would be needed to accompish this.

Hola puedo venderte una maquina nueva completa chocofrutfc@yahoo.es

Click the link to add information to this solution:
Hi, I’m purchasing an ox build workbee cnc router from China but I need to purchase the spindle mount, router and all cables/wires. Please can you give a list and quote of what I will need? I am purchasing the electrical pack with it but it doesn’t come with the cables and all other bits I need. Thank tou

That is a very loaded question that could be replied in so many ways. I will need a more specific question to help you. For instance, I have my machine moving in different directions, but I don't know how to make the machine move according to g-code instructions. Another question could be, I connected all of my electronics and the motors are not moving and I did all of the steps on the electronics video to troubleshoot the problem.

Click the link to add information to this solution:
I have a cnc router that was built from the book "Build your own cnc machine" by james kelley and patrick hood daniel.all the parts were purchased from your company.I have no clue how to work the machine and I need to purchase a spindle (or router) bits , softwear ect , I did mention I don't know how to use the machine !!! Thanks for your help Richard

The greenBull kit (not the assembled) will need the table (the rails for the table is supplied), wires/cables for the stepper motors and stepper motor drivers, smaller gauge wires for digital wire connections (limit switches, drivers to control interface, etc), wires for the spindle connection to the VFD, tubing for water flow to and from the spindle, and a pump and reservoir (we are just about to introduce a small pump/reservoir/radiator/fan system for use with the spindle. The VFD/spindle, stepper motors/drivers and interface board are included.

Click the link to add information to this solution:
If I understand correctly, the greenBull kit comes with a spindle and laser. What else do I need to have a working machine. Obviously a table, do I also need the computer, software, wires, pump and plumbing, electronics, VFD, steppers and controllers?

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

Please call us and we will assist directly with this purchase. 281-815-7701.

Additional Information:
20

Click the link to add information to this solution:
Looking for some sale support as we are having problem placing an order for the following items: 1 blackFoot 4'x8' v4.3 CNC Machine Kit with USB Interface $3281.50 1 Laser Cutter/Engraver with Integrated Computer (1 week lead time) $2100 1 whiteAnt Base Kit (Everything Except the Electronics) $640.00 1 whiteAnt Gen4 Electronics Bundle $345.00 1 Heavy Duty redLeaf System $1550.00

We do offer all of the parts; but it is best to purchase them a la carte. You will probably not want the hardware since this would not conform to a design in metal.

All of the mechanical parts are available here:
https://buildyourcnc.com/CNCMachineMechanicalParts.aspx

All of the electronics you would need is available here:
https://buildyourcnc.com/electronicscombo.aspx

All of the laser components are available here:
https://buildyourcnc.com/LaserComponents.aspx

And the spindles and VFDs are available here:
https://buildyourcnc.com/SpindlesAndAccessories.aspx

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hello, I'm interested in GreenBull 5'x10' CNC machine kit with 40W laser head. Is it possible to receive an offer for this size cnc machine kit with all the mechanics, electronics and laser parts, but without all the wooden parts? We would like to build this kind of laser cutter machine with metal frame and parts. And is it possible also to get 3D drawing for machine? Waiting for your answer.

There is some variation in the outward appearance of laser power supplies due to sourcing through different vendors. However, the basic wiring requirements are the same in each case. For the unit with integrated laser controller, follow the diagram found here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/. The terminals on the signal side will have a 6 connection terminal block -- these are the ones labeled 5V, IN, G, P (or WP), L (or TTL-L), and H (or TTL-H). The High Power side will have 3 inputs for AC power, one high voltage lead, and one return line. Connect these as shown in the diagram as well: the return line goes on the "front" (beam exit end) terminal of the laser tube, the high voltage lead goes to the "back" terminal of the tube, the FG terminal (or G) receives the earth ground wire of the AC power cable, and the two AC terminals receive the line and neutral wires of the AC power cable (it doesn't matter in this case which wire goes to which terminal).

Click the link to add information to this solution:
I purchased the blackTooth Laser Engraver with integrated Laser Control Unit and have been following your instructions. I noticed that the laser tube power supply is different that what is shown in your instructions. Do you have any better wiring guides that I can follow for the version that I received?

If you have an existing PC with a parallel port you will not need to purchase the onboard computer system on the blackTooth laser cutter and engraver. You will want to purchase the blackTooth laser engraver that comes with the parallel interface (breakout board). If you have an existing CNC machine that is being used with this PC, you can disconnect the CNC machine and connect the blackTooth to this PC. You will want to have two configurations for your control software.

Additional Information:
We have a version of the blackTooth that is 110v and 220v. We generally determine which is sent according to the requirements of the customer and in what country they live.

Additional Information:
20

Additional Information:
Parallel Port Configuration BIOS settings and Mach 3.

Click the link to add information to this solution:
I'm interested in purchasing your black tooth laser engraver and am curious what setup to get. I already have a cnc wired via parallel port to my PC. Do I need to purchase the black tooth laser with the integrated computer or can I just disconnect my current cnc's parallel port and connect it to the black tooth laser engraver? Also is the black tooth 110v?