The Honeywell brand goggles meet ANSI certification Z136.1, relating to the safe use of lasers, and are calibrated to optimally block the specific wavelengths of light produced by CO2 lasers (the details are available in the website description here: https://buildyourcnc.com/item/laser-components-goggles-safety-honeywell.) The generic tinted goggles also block the specific CO2 laser wavelengths, but a good deal of other wavelengths as well. That and frame style variation is the basic difference.

Click the link to add information to this solution:
I was wondering what was the difference between the two pair of goggles you are selling for the blacktooth. The tinted laser goggles and the Honeywell laser CO2 goggles

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN A PRINTER CABLE PORT AND USB MOTOR KITS

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN PARALLEL AND USB ELECTRONICS COMBOS MOTOR KITS

Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
Number of Planners 1 1 1
Number of Axis 6 6 6
Out of Band Axis (OBA) 0 1 6
Slave axis (uses up coordinated axes) 3 N/A N/A
Slave motors (does not use up coordinated axes) N/A 4 per Axis 4 per Axis
API Interface - Open to All Hardware Yes Yes Yes
Extended Plugin Support Yes Yes Yes
User customizable GUI Yes Yes Yes
Unified (GUI) Interface - PLC, CNC, etc.. Yes Yes
Unlimited IO Yes Yes Yes
Modbus PLC Yes Yes Yes
PMC (Ladder Logic addressing for cnc/plc) Yes Yes
Unlimited File Size Yes Yes
Tool Path Display Yes Yes Yes
Tool Path Speed & Quality Low High High
Scripting - Customization Yes Yes Yes
LUA Scripting - simple, fast, cross-platform Yes Yes
- Lua sockets (ftp, http, smtp,..) Yes Yes
- SSL (security layer) Yes Yes
- LFS (manage large files and data storage) Yes Yes
- Seriel port Yes Yes
- Enraving of part numbers / serial numbering of parts Yes Yes
- Plugin panel objects Yes Yes
IPC Library for Data Sharing/tracking (Interprocess communication) Yes Yes
Full Feature Screens/Controls Per Machine Type Yes Yes
Currently Availabe: Mill, Router, Lathe, 3d Printer Yes Yes
Multiple gcode Interpruters (Per Machine Type) Yes Yes
Probing - Intergrated in standard screens Yes Yes
Simulated 3d Machining (with additional plugin license) Yes Yes
Tool Life Management (G10 L3 command) Yes
Screw Mapping Yes
Professional Screen Designer (advanced G.U.I.) Yes
- Screen Animation Control Yes
- Screen Integrated Tool Table Control Yes
- Screen Integrated Work Offset Control Yes
- Screen Integrated gcode editor Yes
- Screen Artsoft Wizard Package Integration Yes
Macro B gcode Programming (#variables) Yes
- User definable gcodes via marco calls Yes
- Macro Calls: G65, G66, G66.1 Yes
- gcode via marco call (custom G codes via macro B) Yes
- mcode via macro call (custom M codes via macro B) Yes
- mcode via sub code (custom M code via sup program) Yes
- Conditional gcodes Yes
- set VN call - define variable names Yes
gcode Editor Included Yes
Scripted M code (custom M code via LUA script) Yes Yes
Variable Speed Spindle Yes Yes Yes
Spindle Relay Yes Yes Yes
Coolant relay Yes Yes Yes
Mist Relay Yes Yes Yes
Threading Yes Yes Yes
Rigid Tapping Yes Yes Yes
Single Block Yes Yes Yes
Block Delete Yes Yes Yes
Optional Stop Yes Yes Yes
MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
Cutter Comp Yes Yes Yes
Fanuc Type C Cutter Comp Yes Yes
Fixture Offsets Yes Yes Yes
G51 Scaling Yes Yes Yes
G92 Offsets Yes Yes Yes
G52 Offsets Yes Yes Yes
Event Driven Yes Yes
Multi Line MDI Yes Yes
Subs In MDI Yes Yes
OpenGL Optimization Yes Yes
Multi-platform OS Compatibility Option Yes Yes
Online Support Yes Yes Yes
Phone Support Option Available Yes
Support Priority Yes
Available to End Users as "Do-it-yourself" Yes Yes
Summary - Mach3 versus Mach4 :
Mach4 Hobby is the closest comparable version to Mach3, yet it is still much more advanced. The price point of these versions is nearly
identical. Mach3 is very popular for hobby enthusiest and is used in highly modified form by some great OEM's. In general, Mach4 is more
complex than Mach3 and follows cnc industry standards. Mach3 has many customizations to make it easier for hobby users, but can lead to
difficulties if users plan to apply their knowledge to more advanced systems. Mach4 is built as a full featured cnc controller capable of high
speed machining for servo and stepper systems. Mach3's feature set is complete, while Mach4's will continue to expand. If you are new to cnc,
Artsoft highly recommends using and learning Mach4 even if it appears that Mach3's feature set will be adequate for your needs.

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN MACH3 AND MACH4?

3 axis machines cannot create undercuts in the part.

These videos show the capabilities of 3 and 5 axis machining:

3-axis CNC:

Click the link to add information to this solution:
WHAT THE DIFFERENCE BETWEEN 3 AXIS AND 5 CNC?

The first number is the amount of chromium that is contained in the stainless, i.e., 18 is 18% chromium. The second number is the amount of nickel, i.e., 8 stands for 8% nickel. So 18/8 means that this stainless steel contains 18% chromium and 8% nickel. 18/10 is 18% chromium and 10% nickel. The higher the numbers the more corrosion resistant the material. 18/0 is a misleading designation. Both 18/8 and 18/10 contain nickel and are part of the grade family "300 series" stainless. 18/0 means that there is 18% chromium but zero nickel. When there is no nickel the stainless grade family is the "400 series". 400 series are not as corrosion resistant as the 300 series and are magnetic, where the 300 series are non-magnetic.

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN ROCK CRYSTAL ?

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT'S THE DIFFERENCE BETWEEN PARALLEL BREAKOUT BOARD AND USB ITERFACE?

An axis is a direction of motion controlled by the CNC machine control. It can be linear (motion along a straight line) or circular (a rotary motion). The number of axes a machine has determines it's machining capabilities. A 2.5 axis machine really has three moving axes, but only two axes can move together (most machines sold today are full three axis machines). For machining centers, a three axis machine will have three linear axes. A four or five axis machine will have three linear axes as well as one or two rotary axes.

Note that 2.5 versus 3 axis has yet another context. 2.5 axis machining requires that the machine have three axes, but only two axes must be moving simultaneously at any one time. (Simple operations, like drilling and most milling, fall into this category). On the other hand 3-axis machining requires that all three axes be moving at the same time (More complex operations, like the machining of sculptured surfaces required in molds and airfoils, fall into this category.)

Additional Information:


Additional Information:

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE IN A 2.5 AXIS MACHINE?

Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

Additional Information:

Click the link to add information to this solution:
WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

Click the link to add information to this solution:
WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

The parallel is the most versatile breakout board we have and will work with most of the software out there, but many computers are not equipped with parallel connectors anymore. Parallel adapter cards are available if you don't have a parallel connection on your computer.

The USB interface must be used only with the planet-cnc software, which is great software, but you are still limited to only that software application. This is actually the least expensive option unless you use linux and go with the above option.

Click the link to add information to this solution:
WHATISTHE DIFFERENCE WTIH THE PARALLEL BREAKOUT BOARD AND USB BOARD?

Yes, from our test with clear and opaque acrylic, the CO2 laser can cut fully through.

Click the link to add information to this solution:
Will the 40W CO2 laser cut through clear and color acrylic?

Drawing Cartoons

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT COMMON BETWEEN KUTTY, SHANKAR, LAXMAN AND SUDHIR DAR?

How did you test the laser tube? One of the two mirrors or the laser tube end may be damaged.

Click the link to add information to this solution:
[550] What could be wrong when the CO2 laser tube fires a beam inside but it doesn't go out of the tube?

The password is: 608

Click the link to add information to this solution:
WHAT IS THE SYSTEM PASSWORD FOR LASER CONTROL UNIT?

You can find all of the information including the price on the blackTooth Laser cutter and engraver page found here: https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx

Click the link to add information to this solution:
How much is your ; blackTooth Laser Cutter and Engraver CO2 40W

The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

The mirrors are 25mm wide mirrors.

Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.

Click the link to add information to this solution:
WHAT IS LASER AND LENS FOCAL LENGTH?

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Click the link to add information to this solution:
WHAT CAN ADD TO MY BLACKTOOTH LASER CUTTER MEASURE THE TIME OF USE?

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
WHAT ARE SOME USEFUL MODIFICATIONS CAN APPLY TO THE BLACKTOOTH LASER CUTTER?