This collet will accept tools with a 3/8" (9.525mm) shank. This is a clamping precision grade collet with a TIR (Total Indicated runout) of less than 0.01 mm, or 0.0004 inches.

This is the part of the spindle that will hold and grip the end mill at the spinning part of the spindle. This is a collet for smaller spindles with the ER-11 specification. This collet will accept tools with a 4mm shank.

This is the part of the spindle that will hold and grip the end mill at the spinning part of the spindle. This is a collet for smaller spindles with the ER-11 specification. This collet will accept tools with a 6mm shank.

This is the part of the spindle that will hold and grip the end mill at the spinning part of the spindle. This is a collet for smaller spindles with the ER-11 specification. This collet will accept tools with a 1/4" (6.35mm) shank.

This is the part of the spindle that will hold and grip the end mill at the spinning part of the spindle. This is a collet for smaller spindles with the ER-11 specification. This collet will accept tools with a 1/8" (3.175 mm) shank.

Collet Care Lubricant and Spindle Cleaner. 118 ml bottle. Designed to clean and protect spindle collets.

This collet will accept tools with a 1/2" (12.7mm) shank. This is a clamping precision grade collet with a TIR (Total Indicated runout) of less than 0.01 mm, or 0.0004 inches.

This collet will accept tools with a 1/4" (6.35mm) shank. This is a clamping precision grade collet with a TIR (Total Indicated runout) of less than 0.01 mm, or 0.0004 inches.

This collet will accept tools with a 1/8" (3.175mm) shank. This is a clamping precision grade collet with a TIR (Total Indicated runout) of less than 0.01 mm, or 0.0004 inches.

This collet will accept tools with a 1/2" shank (the shank is the smooth part of the bit that is inserted into the collet). If you don't have the nut below, make sure you get that too. This is a clamping precision grade collet with a TIR (Total Indicated runout) of less than 0.0004 inches (PG - Precision Grade). NOTE: We no longer carry collets for Porter Cable 890 Series

This collet will accept tools with a 1/4" shank (the shank is the smooth part of the bit that is inserted into the collet). If you don't have the nut below, make sure you get that too. This is a clamping precision grade collet with a TIR (Total Indicated runout) of less than 0.0004 inches (PG - Precision Grade). NOTE: We no longer carry collets and nuts for Porter Cable 890 Series or Bosch Colt (PR20EVSK) series

This collet will accept tools with a 1/8" shank (the shank is the smooth part of the bit that is inserted into the collet). If you don't have the nut below, make sure you get that too. This is a clamping precision grade collet with a TIR (Total Indicated runout) of less than 0.0004 inches (PG - Precision Grade). NOTE: We no longer carry collets and nuts for Porter Cable 890 Series or Bosch Colt (PR20EVSK) series

These collets wouldn't be complete without the nut to fasten it on to the router. This nut must be used with these collets. NOTE: We no longer carry collets and nuts for Porter Cable 890 Series or Bosch Colt (PR20EVSK) series

Here is a kit with all of the collets (1/8", 1/4" and 1/2"), nut and spanner wrench. Additionally, this kit contains a cleaning and lubricating solution that has a special blend of ingredients to clean out all of the gunk, rust and other foreign materials that you don't want in your router. This will insure that your tool has minimal runout.