If you take the standard parallel cable BoB (Break Out Board), then you will need control software (Mach 3 or EMC2) and CAM software to make your G-Code (such as CamBam). Personally I use CamBam and Mach 3, they work beautifully but don't expect to turn them on and know how they work out of the box. Give yourself a few weeks to get familiar with the basics. CamBam is VERY powerful software for it's price. I'm surprised how much I keep learning on what I can do with it...I highly recommend it if you want as much control as possible.

Mach 3 + CamBam as a bundle costs $310. EMC2 will give you a free replacement for Mach 3 and is exclusively for Linux.

If you use the USB BoB, it will cost an extra $75 + $75 for the software. This is an all-in-one package so no need for Mach 3 or CamBam.

For etching rasters (jpeg, bmp, tiff, non-vectors, photos), I highly recommend PicEngrave. It has been a labor of love for the past 9 years and John has done a wonderful job with it. It easily compares in quality compared to software that is in the $200-$300 range. John's software runs $40 and can be found here: http://picengrave.com/ (don't let the modest website fool you, this stuff can do amazing things). DotG and the Mach3 engrave plugin are two other options and instructions can be found on Dustans page in the gallery on buildyourcnc.com website.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

Yes, it is found in laser components section

Click the link to add information to this solution:
DO YOU GUYS SELL THE POTENTIOMETER FOR YOUR LASER SYSTEM BY ITSELF

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
WHAT ARE SOME USEFUL MODIFICATIONS CAN APPLY TO THE BLACKTOOTH LASER CUTTER?

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Click the link to add information to this solution:
WHAT CAN ADD TO MY BLACKTOOTH LASER CUTTER MEASURE THE TIME OF USE?

Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

Additional Information:

Click the link to add information to this solution:
WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:


Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:


Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:


Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:

Click the link to add information to this solution:
DOES ANY OF THE SOFTWARE THAT COMES WITH IT COMPATIBLE MAC 10.6?

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

Click the link to add information to this solution:
WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

The Greenbull machine can cut a very wide variety of materials ranging from foam to aluminum. We recommend the use of our 2.2kW spindle to allow the greatest flexibility. Aside from that, the most important thing is to use an appropriate end mill for the material you are cutting and to use appropriate speeds and feed rates.



BYCNC Response:
Our 40W laser can cut up to about 1/4" materials ranging from wood and acrylic down through lighter materials such as leather, fabric, foam, etc. Speed and final cut are greatly enhanced by an air assist upgrade. We also offer an 80W laser which has approximately twice the capabilities of the 40W.

Additional Information:

Click the link to add information to this solution:
WHAT MATERIALS CAN THE GREENBULL MACHINE CUT? LASER ETCH?

A standard 40W CO2 laser will cut up to 1/4" thick of material, be it wood, acrylic, card stock, leather, fabric, foam, cork, etc. (Decent speed and final cut are heavily dependent on a strong air assist upgrade)

Metals cannot be cut due to the power level and wavelength of the CO2 laser. But it can be marked with special solutions like Cermark or Thermark.

Click the link to add information to this solution:
WHAT THICKNESS OF MATERIAL CAN THE BLACKTOOTH LASER CUT?

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

Click the link to add information to this solution:
WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

The base greenLean CNC Machine Kit package includes:
- Structure (all of the structural parts that make up the gantry and rib system). The structure does not include the spoilboard.
- Hardware (All of the fasteners, like screws, nuts, cross dowels, washers, etc.)
- Mechanical components (bearings, rails, sprockets, shafts, etc.)
- Electronics (3 NEMA 651 Motors, 3 6.0 Amp drivers power supply, interface card to connect the drivers to a computer, and 91 feet of motor cable. Hookup wire to connect the electronics is not included.)
- 2.2kw Spindle and VFD

Here is a link to the greenLean CNC Macnine page: https://www.buildyourcnc.com/item/cnc-machine-greenLean-v1

Click the link to add information to this solution:
WHAT COMES IN THE BOX FOR BASIC GREENLEAN?

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW COMPLEX IS YOUR KIT TO ASSEMBLE, AND MOST IMPORTANTLY - HARD IT SETUP CONTROL THE LASER WITH MACH3?

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
WHAT CAN USE BELOW MY WORKPIECE AS SUBSTRATE IN BLACKTOOTH LASER CUTTER?

PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
WHAT ELSE DO I NEED WITH THE MACHINE?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

It is not necessary to connect the spindle VFD (Variable Frequency Drive also called an Inverter) to the computer or CNC motion electronics. The VFD can be controlled independently using the control panel on the VFD. The control panel has the ability to control all aspects of the spindle including Speed, Torque, limits, etc. However, you can connect the VFD to the computer so the CNC control program can control the spindle during the CNC Machine operation. You will need to connect the VFD to the computer via a serial conection (in this case, it is the RS-485 protocol).

The following are instructions on how to connect the VFD to Mach3 via this RS-485 serial connection.

The first thing you will need is the dynamic link library to pair with mach3 called the Huanyang VFD Mach3 PlugIn. You can find this file at the mach3 support forum here: http://www.machsupport.com/forum/index.php/topic,14182.0.html

You will also need to download the Microsoft .net 3.5 framework and install it: https://www.microsoft.com/en-us/download/details.aspx?id=21

Follow the pdf that comes with the library file, but here is a synopsis of what you need to do (I also added a lot more information that may be useful during this process as the manual does not cover the main connections that need to be done):

You will need to program your VFD so that it knows how to communicate with mach3 and the computer (go into the programming mode of the VFD and change these parameters):
- PD001 - value 2 - Enables with communication aspect of the VFD
- PD002 - value 2 - Enables frequency control from the communcations port
- PD163 - value 1 - VFD address
- PD164 - value 1 - Baud rate of 9600 (speed of the communication)
- PD165 - value 3 - 8N1 RTU - 8 bits (that's the size of the word that gets communicated), N (No parity or no error checking) and 1 (1 stop bit)

Copy the dll file to the PlugIns folder of mach3.

Connect the RX and TX lines to your computer. There are a couple ways you can do this, but the recommended way would be to use an FTDI USB device which converts a USB to a serial com port. The device will have Rx and Tx connectors to connect to the VFD terminals with the same labels. This method is recommended since serial ports are not as common in computers these days.

Next, you will need to configure mach3 to use the plugin library. Start mach3 and click on Menu -> config ->Config Plugins. Enable the new plugin by clicking on the red cross on the left column next to the plug in. Restart mach3 after doing this.

No you need to configure mach3 to use the HuanyangVFD plugin. Go to the ports & pins configuration and select the spindle setup tab. Make sure that the Disable Spindle Relays checkbox is unchecked. We don't want mach3 to output a signal for a relay since the spindle will start up and turn off within the VFD and not from an external relay.

Next, go to the HuanyangVFD settings by clicking on Menu -> plugin control -> HuanyangVFD. Set the parameters to the same settings you put into the VFD programming. The com port will be shown as new hardward when you plug in the USB FTDI device. A little bubble will be displayed at the bottom right where it will notify you that a new device is being installed (be patient while windows assigns a com port). Alternatively, you can use the windows device manager to see which port was set for the new USB FTDI device). You may need to restart mach3 several times until you get the correct information displayed in the PD001 and PD002 fields. When the com port is correct and the other parameters, like baud and VFD address is the same as you entered in the programming, then the PD001 and PD002 will show the number 2, otherwise, a 99 will appear which means that communication was not successful.

You can now control the on/off and RPM of the spindle using the RS485 communication between mach3 and the VFD.

Additional Information:
The question was how to connect the spindle to the redfy. I did not receive a VFD.
I have the redFly system and a 2.2kW Spindle - 110V how do i connect the spindle?

Additional Information:
If you received a spindle without a VFD, please contact us asap. Our spindle will not work without a VFD.

Additional Information:
Hi, how is this setup in mach4?

Click the link to add information to this solution:
I HAVE THE REDFLY SYSTEM AND A 2.2KW SPINDLE - 110V HOW DO CONNECT SPINDAL?

PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
WHAT NOT INCLUDED WITH THE MACHINE?

That shouldn't be a problem. I will need the current rating for the motors. We can subtract the price of the motors. and you can add you own. If you want us to solder the cable to the round connectors and them motor, you would need to send the motors to us.

Let me know and I can send a paypal invoice for the redLeaf without motors.

Click the link to add information to this solution:
DON'T WANT TO USE MY OWN MOTORS FOR THE REDLEAF CNC COMPUTER SYSTEM.

You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

Additional Information:
wire size

Click the link to add information to this solution:
WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?