[ Log In ]
[ Register ]

Question #: 13552

Question: WHAT COMES IN THE BOX FOR BASIC GREENLEAN?

Current Solution

The base greenLean CNC Machine Kit package includes:
- Structure (all of the structural parts that make up the gantry and rib system). The structure does not include the spoilboard.
- Hardware (All of the fasteners, like screws, nuts, cross dowels, washers, etc.)
- Mechanical components (bearings, rails, sprockets, shafts, etc.)
- Electronics (3 NEMA 651 Motors, 3 6.0 Amp drivers power supply, interface card to connect the drivers to a computer, and 91 feet of motor cable. Hookup wire to connect the electronics is not included.)
- 2.2kw Spindle and VFD

Here is a link to the greenLean CNC Macnine page: https://www.buildyourcnc.com/item/cnc-machine-greenLean-v1

Respond:

Other Possible Solutions to this Question

  • WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

    Shipping crate 121" X 36" X 92"

    Weight 511 LBS

    Additional Information:
    ship in india pls

    Additional Information:
    International shipping rates can be determined by:
    - adding products to the cart
    - go to the cart and enter shipped by address
    - and pressing the calculate shipping button

    Click the link to add information to this solution:
    WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

  • GREENLEAN SILICON TUBE FOR SPINDLE

    The greenlean requires 56 feet of 1/4 Inside Diameter and 3/8 Outside Diameter silicon tube for the spindle.

    Additional Information:
    20

    Additional Information:
    20

    Click the link to add information to this solution:
    GREENLEAN SILICON TUBE FOR SPINDLE

  • WHAT THE TECHNICAL SUPPORT FOR STAMPS.COM?

    The stamps.com technical support is developersupport@stamps.com

    Click the link to add information to this solution:
    WHAT THE TECHNICAL SUPPORT FOR STAMPS.COM?

  • WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to add information to this solution:
    WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

  • WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

    Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
    To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
    The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
    Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


    Link:
    https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

    Click the link to add information to this solution:
    WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to add information to this solution:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to add information to this solution:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to add information to this solution:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

  • WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

    76" X 40" X 26"
    230 LBS

    Click the link to add information to this solution:
    WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

  • WHAT IS THE LEAD TIME FOR BLACKTOE?

    You can expect a one week lead time for our machines.

    Click the link to add information to this solution:
    WHAT IS THE LEAD TIME FOR BLACKTOE?

  • WHAT IS THE LEAD TIME FOR BLACKFOOT

    You can expect a one week lead time for our machines.

    Click the link to add information to this solution:
    WHAT IS THE LEAD TIME FOR BLACKFOOT

  • WHAT ARE THE ROLLER CHAIN LENGTHS FOR GREENBULL 4X

    The roller chain lengths for the greenBull 4x is:
    - 13 feet for each side of the X axis (total of 26 feet), and
    - 6 feet for the Y-axis

    Click the link to add information to this solution:
    WHAT ARE THE ROLLER CHAIN LENGTHS FOR GREENBULL 4X

  • WHAT IS THE LEAD TIME FOR REDFROG?

    You can expect a two week lead time for the redFrog pick and place machine.

    Click the link to add information to this solution:
    WHAT IS THE LEAD TIME FOR REDFROG?

  • WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

    You can expect a one week lead time for our machines.

    Click the link to add information to this solution:
    WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

  • WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

    Shipping crate size 121" X 36" X 92"

    Weight 511 LBS

    Click the link to add information to this solution:
    WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

  • WHAT IS THE SYSTEM PASSWORD FOR LASER CONTROL UNIT?

    The password is: 608

    Click the link to add information to this solution:
    WHAT IS THE SYSTEM PASSWORD FOR LASER CONTROL UNIT?

  • WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

    You can expect a two week lead time for the redFrog pick and place machine.

    Click the link to add information to this solution:
    WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

    The blackfoot requires a total of 50 feet of cable.

    The X axis needs 15 feet
    The Y axis needs 17 feet
    and the Z-axis needs 18 feet

    These are 20 gauge 4 conductor cable.

    Click the link to add information to this solution:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

  • WHAT THE MOST POPULAR INDOOR SPORT IN U.S.A.?

    Basketball is the most popular indoor sport in the USA

    Additional Information:
    boxing

    Additional Information:
    boxing

    Additional Information:
    boxing

    Additional Information:
    Basketball


    Additional Information:
    Basketball


    Additional Information:
    Which indoor sport is the most popular in the US

    Additional Information:
    Who recorded A Boy Named Sue

    Click the link to add information to this solution:
    WHAT THE MOST POPULAR INDOOR SPORT IN U.S.A.?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.