[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 635

Question: WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

Current Solution

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Respond:

Other Possible Solutions to this Question

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

    The blackfoot requires a total of 50 feet of cable.

    The X axis needs 15 feet
    The Y axis needs 17 feet
    and the Z-axis needs 18 feet

    These are 20 gauge 4 conductor cable.

    Click the link to respond:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

  • HOW LONG SHOULD THE MOTOR CABLES BE FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    HOW LONG SHOULD THE MOTOR CABLES BE FOR BLACKTOE

  • WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

    You can expect a one week lead time for our machines.

    Click the link to respond:
    WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

  • WHAT IS THE LEAD TIME FOR BLACKTOE?

    You can expect a one week lead time for our machines.

    Click the link to respond:
    WHAT IS THE LEAD TIME FOR BLACKTOE?

  • WHAT IS THE LEAD TIME FOR BLACKTOE?

    You can expect a two week lead time for the redFrog pick and place machine.

    Click the link to respond:
    WHAT IS THE LEAD TIME FOR BLACKTOE?

  • CABLE LENGTHS FOR THE BLACKFOOT

    The blackfoot requires a total of 50 feet of cable.

    The X axis needs 15 feet
    The Y axis needs 17 feet
    and the Z-axis needs 18 feet

    These are 20 gauge 4 conductor cable.

    Click the link to respond:
    CABLE LENGTHS FOR THE BLACKFOOT

  • WHAT LEAD TIME CAN EXPECT FOR BLACKTOE SO PICK UP THE MACHINE?

    You can expect a one week lead time for our machines.

    Click the link to respond:
    WHAT LEAD TIME CAN EXPECT FOR BLACKTOE SO PICK UP THE MACHINE?

  • What are the jumpers used for on the c-10 breakout board

    The USB is only used for powering the parallel breakout board.

    Click the link to respond:
    What are the jumpers used for on the c-10 breakout board

  • What are the jumpers used for on the c-10 breakout board

    endmill-singleflute
    endmill-twoflute
    endmill-compression
    carveandengrave
    endmill-surfacing

    Click the link to respond:
    What are the jumpers used for on the c-10 breakout board

  • What size forstner are used in the book build your own cnc

    That was a very long time ago, but I think I was using 3/4". You can use a size just larger than the outer width of the nut.

    Click the link to respond:
    What size forstner are used in the book build your own cnc

  • THE BLACKTOE REQUIRES HOW MUCH MOTOR CABLE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    THE BLACKTOE REQUIRES HOW MUCH MOTOR CABLE

  • My question about motor tuning for the blacktoe in Mach 3 was for the aceleration and velocity settings what are the recomended settings

    In the customer service live, just enter "motor tuning" and it will give you a list of all the recommended or default settings for our machines. However the acceleration and velocity for the greenBull(other machines) will be an actual determination on your trials. You will want the highest possible acceleration and velocity without the motors stalling, so you can do increments of ten to be on the safe side, if it is too slow try increments of 25.

    The steps per inch is dependent on the microstepping:
    Steps/Inch for the x and y
    Steps = 200 motor steps per revolution x 16 microsteps = 3200 steps
    Inches = sprocket number of teeth x pitch of the sprocket = 14 x .25" = 3.5 inches
    steps/inch = 3200 / 3.5 = 914.28
    This is really a starting point. You will then need to use the mach3 calibration function to get the perfect steps/inch value. Use as long a measurement as possible when calibrating.

    Velocity:
    Start with a value of 1000 ipm. Increase this value with a relatively low acceleration at about 10. You will notice at a particular velocity that it will stall. This is your stall velocity. I would take the stall velocity and reduce it by about 30% to 50% which should give you a good final safe velocity.

    Acceleration:
    Once the velocity is found, raise the acceleration until it start to stall at a low velocity. Reduce the acceleration by about the same percentage to stick with a safe acceleration.

    The acceleration is mostly dependent on torque (current) and the top speed is dependent on the amount of voltage.

    Give some tests with all of the axes running at the same time. If you notice and stalling, reduce velocities and acceleration depending on when the stall happens (top end, or acceleration curve).


    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in
    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in
    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:


    Additional Information:
    4th axis


    Additional Information:

    Click the link to respond:
    My question about motor tuning for the blacktoe in Mach 3 was for the aceleration and velocity settings what are the recomended settings

  • blackToe 2'x4' CNC Router - What are the actual x and y cutting dimensions (eg: 22"x46")

    The actual cutting dimensions for our blackToe machine is 2'(24") x 4'(48"), the overall size of the structure built is a bit larger so that our customers have the actual size mentioned with each of our machines!

    Click the link to respond:
    blackToe 2'x4' CNC Router - What are the actual x and y cutting dimensions (eg: 22"x46")

  • What profile do I use in VCarve for a BlackToe?

    The blackToe is a CNC Router based on standard CNC Routing and milling actions. If you are referring to a profile machining operation (where the path follows the inside or outside edge of a polygon, line, arc or circle) then the profile is actually more a function what you want the CNC router (blackToe in this case) to do. A profile expects a specific end mill in the spindle and requires the specifications of the end mill in the profile operation.

    If you are referring to profile to mean "post processor" or specifications (profile of the control) for the g-code interpretation for a specific control program (like Mach3), then you will need to set the post processor in VCarve post-processor to the control program you are using.

    Please provide more specific information here so I can delve in a bit deeper.

    Click the link to respond:
    What profile do I use in VCarve for a BlackToe?

  • What is the footprint of the blacktoe 4x2?

    The footprint of the optional blackToe table, is from its most outward points (73" inches x 34" inches) and for the gantry itself (36.5" inches width x 17.25" inches length x 29.5" inches height).

    Additional Information:
    Thank you. Let me ask a clarification question.From this description, can I presume that the 4x2 router kit can be attached to a torsion box-like table that is 73"x34", has a two inch overhang, and four inches of space below the overhang, and that the fully assembled unit will fit in a space that is 73" long by 36.5" wide (with a little bit of clearance, of course)? If I have extra space in the long direction, can I get longer rails and extend the table?

    Click the link to respond:
    What is the footprint of the blacktoe 4x2?

  • WHAT LENGTH OF MOTOR CABLE SHOULD BE USED WTIH THE BLUECHICK V4.2

    The recommended total length of motor cable should be 15 feet for the blueChick v4.2

    Z - 6 feet
    Y - 5 feet
    X- 4 feet

    20 AWG 4 conductor

    If your drivers will be positioned farther from the machine, you may need longer cable.

    Click the link to respond:
    WHAT LENGTH OF MOTOR CABLE SHOULD BE USED WTIH THE BLUECHICK V4.2

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.