Yes, other CO2 laser tubes will work fine with our laser controller (including the Reci tube). Our laser controller is a digital based controller that controls the laser tube power supply, the motor drivers and other peripherals by outputting digital signals to these devices.

Laser controller URL:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System

Click the link to add information to this solution:
Can other types of laser tubes work with the controller you are selling, for example, the 80W Reci tube?

The Greenbull machine can cut a very wide variety of materials ranging from foam to aluminum. We recommend the use of our 2.2kW spindle to allow the greatest flexibility. Aside from that, the most important thing is to use an appropriate end mill for the material you are cutting and to use appropriate speeds and feed rates.



BYCNC Response:
Our 40W laser can cut up to about 1/4" materials ranging from wood and acrylic down through lighter materials such as leather, fabric, foam, etc. Speed and final cut are greatly enhanced by an air assist upgrade. We also offer an 80W laser which has approximately twice the capabilities of the 40W.

Additional Information:

Click the link to add information to this solution:
WHAT MATERIALS CAN THE GREENBULL MACHINE CUT? LASER ETCH?

The roller chain lengths for the greenBull 4x is:
- 13 feet for each side of the X axis (total of 26 feet), and
- 6 feet for the Y-axis

Click the link to add information to this solution:
WHAT LENGTHS OF ROLLER CHAIN DO I USE FOR THE GREENBULL 4X CNC?

Yes, the vertical laser XL (VLXL) can use a laser tube with a higher wattage than 80 watts. The maximum wattage depends on the length of the laser tube. As the wattage of the laser tube increases, the length of the laser tube also increases. The inside clearance of the Vertical Laser XL will allow a 130-watt CO2 laser tube to be used.

Click the link to add information to this solution:
[510] Can this machine use a bigger laser tube than 80W?

The roller chain lengths for the greenBull 4x is:
- 13 feet for each side of the X axis (total of 26 feet), and
- 6 feet for the Y-axis

Click the link to add information to this solution:
WHAT ARE THE ROLLER CHAIN LENGTHS FOR GREENBULL 4X

An 80 watt laser can cut plywood up to 1/2 inch thick. Make sure to use a high pressure source of air to knock out all of the charring during the cutting process so the laser can work efficiently.

Additional Information:
I have a Chinese 80W laser. Just finished a cut test with 1/2" plywood. It cut through at 95% power 7-4mm/s with significant charring after two passes with no refocusing done between passes.

Additional Information:
That's great information. What is your PSI of the air assist on your laser? What focal lens distance do you have? And where did you place the focus of the lens (at the surface, or within the material)?

Click the link to add information to this solution:
What is the max thickness of material that the 80W laser can cut in plywood?

76" X 40" X 26"
230 LBS

Click the link to add information to this solution:
WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

If you use the 2.2kW spindle, it can cut at 3/4 inch or 19 mm deep with at least a 1/4" cutting diameter single flute end mill. You will get better results with larger diameter end mills, but that is the worst case scenario. I still recommend doing a finishing pass on the edge to make sure everything is perfect.

Click the link to add information to this solution:
CAN THE GREENBULL CUT 18MM BIRCH IN ONE PASS?

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


Link:
https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

Click the link to add information to this solution:
WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

We use purified water, but adding some coolant can be a benefit. The addition of coolant can keep the water in a state that maintains no growth of foreign organism like algae and the such. Additionally, If you are in a colder climate, antifreeze will work well.

Additional Information:

Click the link to add information to this solution:
Do you recomend distilled water or coolant for your 80W laser tube with the CW-3000?

The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

Click the link to add information to this solution:
WHAT DOES THE GREENBULL KIT INCLUDE AND DO I NEED TO INCLUDE?

Cutting metals with a CO2 laser is nearly impossible with just the laser by itself, no matter what the power. The wavelength that a CO2 laser outputs is not best for cutting metals.

However, if you add oxygen as a cutting assist in the cutting process, metals can be cut, but we do not advise this as it is very dangerous.

Click the link to add information to this solution:
What metal sheets can I cut with the 80W laser? What thickness, alumium, steel? What about the 100 or 130W upgrades?

The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

Previous Solution:
The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

Additional Information:



Additional Information:

Click the link to add information to this solution:
WHICH MACHINE SHOULD I BUY, THE GREENBULL OR BLACKFOOT?

The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

Previous Solution:
The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

Additional Information:



Additional Information:

Click the link to add information to this solution:
SHOULD I SELECT THE GREENBULL OR BLACKFOOT CNC MACHINE?

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Click the link to add information to this solution:
WHAT CAN ADD TO MY BLACKTOOTH LASER CUTTER MEASURE THE TIME OF USE?

Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

Additional Information:

Click the link to add information to this solution:
WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

Yes, it is found in laser components section

Click the link to add information to this solution:
DO YOU GUYS SELL THE POTENTIOMETER FOR YOUR LASER SYSTEM BY ITSELF

You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

Additional Information:
wire size

Click the link to add information to this solution:
WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
WHAT ARE SOME USEFUL MODIFICATIONS CAN APPLY TO THE BLACKTOOTH LASER CUTTER?