[ Log In ]
[ Register ]

Question #: 135

Question: What is the difference between 18/8 and 18/10 stainless steel?

Current Solution

The first number is the amount of chromium that is contained in the stainless, i.e., 18 is 18% chromium. The second number is the amount of nickel, i.e., 8 stands for 8% nickel. So 18/8 means that this stainless steel contains 18% chromium and 8% nickel. 18/10 is 18% chromium and 10% nickel. The higher the numbers the more corrosion resistant the material. 18/0 is a misleading designation. Both 18/8 and 18/10 contain nickel and are part of the grade family "300 series" stainless. 18/0 means that there is 18% chromium but zero nickel. When there is no nickel the stainless grade family is the "400 series". 400 series are not as corrosion resistant as the 300 series and are magnetic, where the 300 series are non-magnetic.

Respond:

Other Possible Solutions to this Question

  • WHAT IS THE DIFFERENCE BETWEEN A PRINTER CABLE PORT AND USB MOTOR KITS

    The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

    The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

    The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

    Additional Information:


    Additional Information:


    Additional Information:
    USB Motion controller breakout board work with planet cnc software?

    Click the link to add information to this solution:
    WHAT IS THE DIFFERENCE BETWEEN A PRINTER CABLE PORT AND USB MOTOR KITS

  • WHAT IS THE DIFFERENCE BETWEEN PARALLEL AND USB ELECTRONICS COMBOS MOTOR KITS

    The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

    The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

    The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

    Additional Information:


    Additional Information:


    Additional Information:
    USB Motion controller breakout board work with planet cnc software?

    Click the link to add information to this solution:
    WHAT IS THE DIFFERENCE BETWEEN PARALLEL AND USB ELECTRONICS COMBOS MOTOR KITS

  • WHAT IS THE DIFFERENCE BETWEEN MACH3 AND MACH4?

    Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
    Number of Planners 1 1 1
    Number of Axis 6 6 6
    Out of Band Axis (OBA) 0 1 6
    Slave axis (uses up coordinated axes) 3 N/A N/A
    Slave motors (does not use up coordinated axes) N/A 4 per Axis 4 per Axis
    API Interface - Open to All Hardware Yes Yes Yes
    Extended Plugin Support Yes Yes Yes
    User customizable GUI Yes Yes Yes
    Unified (GUI) Interface - PLC, CNC, etc.. Yes Yes
    Unlimited IO Yes Yes Yes
    Modbus PLC Yes Yes Yes
    PMC (Ladder Logic addressing for cnc/plc) Yes Yes
    Unlimited File Size Yes Yes
    Tool Path Display Yes Yes Yes
    Tool Path Speed & Quality Low High High
    Scripting - Customization Yes Yes Yes
    LUA Scripting - simple, fast, cross-platform Yes Yes
    - Lua sockets (ftp, http, smtp,..) Yes Yes
    - SSL (security layer) Yes Yes
    - LFS (manage large files and data storage) Yes Yes
    - Seriel port Yes Yes
    - Enraving of part numbers / serial numbering of parts Yes Yes
    - Plugin panel objects Yes Yes
    IPC Library for Data Sharing/tracking (Interprocess communication) Yes Yes
    Full Feature Screens/Controls Per Machine Type Yes Yes
    Currently Availabe: Mill, Router, Lathe, 3d Printer Yes Yes
    Multiple gcode Interpruters (Per Machine Type) Yes Yes
    Probing - Intergrated in standard screens Yes Yes
    Simulated 3d Machining (with additional plugin license) Yes Yes
    Tool Life Management (G10 L3 command) Yes
    Screw Mapping Yes
    Professional Screen Designer (advanced G.U.I.) Yes
    - Screen Animation Control Yes
    - Screen Integrated Tool Table Control Yes
    - Screen Integrated Work Offset Control Yes
    - Screen Integrated gcode editor Yes
    - Screen Artsoft Wizard Package Integration Yes
    Macro B gcode Programming (#variables) Yes
    - User definable gcodes via marco calls Yes
    - Macro Calls: G65, G66, G66.1 Yes
    - gcode via marco call (custom G codes via macro B) Yes
    - mcode via macro call (custom M codes via macro B) Yes
    - mcode via sub code (custom M code via sup program) Yes
    - Conditional gcodes Yes
    - set VN call - define variable names Yes
    gcode Editor Included Yes
    Scripted M code (custom M code via LUA script) Yes Yes
    Variable Speed Spindle Yes Yes Yes
    Spindle Relay Yes Yes Yes
    Coolant relay Yes Yes Yes
    Mist Relay Yes Yes Yes
    Threading Yes Yes Yes
    Rigid Tapping Yes Yes Yes
    Single Block Yes Yes Yes
    Block Delete Yes Yes Yes
    Optional Stop Yes Yes Yes
    MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
    Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
    MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
    Cutter Comp Yes Yes Yes
    Fanuc Type C Cutter Comp Yes Yes
    Fixture Offsets Yes Yes Yes
    G51 Scaling Yes Yes Yes
    G92 Offsets Yes Yes Yes
    G52 Offsets Yes Yes Yes
    Event Driven Yes Yes
    Multi Line MDI Yes Yes
    Subs In MDI Yes Yes
    OpenGL Optimization Yes Yes
    Multi-platform OS Compatibility Option Yes Yes
    Online Support Yes Yes Yes
    Phone Support Option Available Yes
    Support Priority Yes
    Available to End Users as "Do-it-yourself" Yes Yes
    Summary - Mach3 versus Mach4 :
    Mach4 Hobby is the closest comparable version to Mach3, yet it is still much more advanced. The price point of these versions is nearly
    identical. Mach3 is very popular for hobby enthusiest and is used in highly modified form by some great OEM's. In general, Mach4 is more
    complex than Mach3 and follows cnc industry standards. Mach3 has many customizations to make it easier for hobby users, but can lead to
    difficulties if users plan to apply their knowledge to more advanced systems. Mach4 is built as a full featured cnc controller capable of high
    speed machining for servo and stepper systems. Mach3's feature set is complete, while Mach4's will continue to expand. If you are new to cnc,
    Artsoft highly recommends using and learning Mach4 even if it appears that Mach3's feature set will be adequate for your needs.

    Click the link to add information to this solution:
    WHAT IS THE DIFFERENCE BETWEEN MACH3 AND MACH4?

  • WHAT THE DIFFERENCE BETWEEN 3 AXIS AND 5 CNC?

    3 axis machines cannot create undercuts in the part.

    These videos show the capabilities of 3 and 5 axis machining:

    3-axis CNC:

    &feature=fvwrel

    5-axis CNC:
    &feature=related

    Additional Information:


    Additional Information:


    Additional Information:


    Additional Information:


    Additional Information:


    Additional Information:


    Additional Information:

    Click the link to add information to this solution:
    WHAT THE DIFFERENCE BETWEEN 3 AXIS AND 5 CNC?

  • WHAT IS THE DIFFERENCE BETWEEN ROCK CRYSTAL ?

    The first number is the amount of chromium that is contained in the stainless, i.e., 18 is 18% chromium. The second number is the amount of nickel, i.e., 8 stands for 8% nickel. So 18/8 means that this stainless steel contains 18% chromium and 8% nickel. 18/10 is 18% chromium and 10% nickel. The higher the numbers the more corrosion resistant the material. 18/0 is a misleading designation. Both 18/8 and 18/10 contain nickel and are part of the grade family "300 series" stainless. 18/0 means that there is 18% chromium but zero nickel. When there is no nickel the stainless grade family is the "400 series". 400 series are not as corrosion resistant as the 300 series and are magnetic, where the 300 series are non-magnetic.

    Click the link to add information to this solution:
    WHAT IS THE DIFFERENCE BETWEEN ROCK CRYSTAL ?

  • WHAT'S THE DIFFERENCE BETWEEN PARALLEL BREAKOUT BOARD AND USB ITERFACE?

    The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

    The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

    The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

    Additional Information:


    Additional Information:


    Additional Information:
    USB Motion controller breakout board work with planet cnc software?

    Click the link to add information to this solution:
    WHAT'S THE DIFFERENCE BETWEEN PARALLEL BREAKOUT BOARD AND USB ITERFACE?

  • WHAT IS THE DIFFERENCE IN A 2.5 AXIS MACHINE?

    An axis is a direction of motion controlled by the CNC machine control. It can be linear (motion along a straight line) or circular (a rotary motion). The number of axes a machine has determines it's machining capabilities. A 2.5 axis machine really has three moving axes, but only two axes can move together (most machines sold today are full three axis machines). For machining centers, a three axis machine will have three linear axes. A four or five axis machine will have three linear axes as well as one or two rotary axes.

    Note that 2.5 versus 3 axis has yet another context. 2.5 axis machining requires that the machine have three axes, but only two axes must be moving simultaneously at any one time. (Simple operations, like drilling and most milling, fall into this category). On the other hand 3-axis machining requires that all three axes be moving at the same time (More complex operations, like the machining of sculptured surfaces required in molds and airfoils, fall into this category.)

    Additional Information:


    Additional Information:

    Click the link to add information to this solution:
    WHAT IS THE DIFFERENCE IN A 2.5 AXIS MACHINE?

  • WHATISTHE DIFFERENCE WTIH THE PARALLEL BREAKOUT BOARD AND USB BOARD?

    The parallel is the most versatile breakout board we have and will work with most of the software out there, but many computers are not equipped with parallel connectors anymore. Parallel adapter cards are available if you don't have a parallel connection on your computer.

    The USB interface must be used only with the planet-cnc software, which is great software, but you are still limited to only that software application. This is actually the least expensive option unless you use linux and go with the above option.

    Click the link to add information to this solution:
    WHATISTHE DIFFERENCE WTIH THE PARALLEL BREAKOUT BOARD AND USB BOARD?

  • WHAT COMMON BETWEEN KUTTY, SHANKAR, LAXMAN AND SUDHIR DAR?

    Drawing Cartoons

    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    WHAT COMMON BETWEEN KUTTY, SHANKAR, LAXMAN AND SUDHIR DAR?

  • WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

    Shipping crate size 121" X 36" X 92"

    Weight 511 LBS

    Click the link to add information to this solution:
    WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

  • WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

    Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

    Additional Information:

    Click the link to add information to this solution:
    WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

  • WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

    You can expect a two week lead time for the redFrog pick and place machine.

    Additional Information:

    Click the link to add information to this solution:
    WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

  • WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

    Shipping crate 121" X 36" X 92"

    Weight 511 LBS

    Additional Information:
    ship in india pls

    Additional Information:
    International shipping rates can be determined by:
    - adding products to the cart
    - go to the cart and enter shipped by address
    - and pressing the calculate shipping button

    Click the link to add information to this solution:
    WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

  • WHAT IS THE PICK AND PLACE LEAD TIME?

    You can expect a two week lead time for the redFrog pick and place machine.

    Additional Information:

    Click the link to add information to this solution:
    WHAT IS THE PICK AND PLACE LEAD TIME?

  • WHAT DOES THE GREENBULL KIT INCLUDE AND DO I NEED TO INCLUDE?

    The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

    Click the link to add information to this solution:
    WHAT DOES THE GREENBULL KIT INCLUDE AND DO I NEED TO INCLUDE?

  • WHAT ARE THE BLACKTOOTH LENS SIZES AND FOCAL LENGTH SPECIFICATIONS?

    The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

    The mirrors are 25mm wide mirrors.

    Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.

    Click the link to add information to this solution:
    WHAT ARE THE BLACKTOOTH LENS SIZES AND FOCAL LENGTH SPECIFICATIONS?

  • WHAT IS THE MOST EASY WAY TO HOOK UP MILL IN THAT AUTOMATICALLY STARTS WHEN CYCLE STARTS, AND STOPS GCODE THROUGH?

    Does your breakout board (interface) have a relay? If so, you can connect one of the router/spindle's ac lines through the relay. The M3, M4 and M5 codes are used to control the router/spindle. Typically, the M codes are automatically added to the g-code regardless if you configure this in your CAM software. If you have the breakout board from buildyourcnc, you can go to the product page for the breakout board and the relay connection diagram and narrative is in the instructions on that page.

    Click the link to add information to this solution:
    WHAT IS THE MOST EASY WAY TO HOOK UP MILL IN THAT AUTOMATICALLY STARTS WHEN CYCLE STARTS, AND STOPS GCODE THROUGH?

  • AND WHAT SIZES ARE THE PACKAGES OF MACHINE.

    the package sizes will be listed in your shopping cart, in the item detail. The site will also fully calculate shipping charges directly from the carrier, for each package you purchase.

    Additional Information:

    Click the link to add information to this solution:
    AND WHAT SIZES ARE THE PACKAGES OF MACHINE.

  • THERE ANY STANDARD FOR A DISTANCE BETWEEN CELLULAR BASE STATION AND RESIDENTIAL AREA?

    The two main constraints on siting cellular base stations near residential areas are government exposure limits and local zoning ordinances. Various governments have limits for human exposure to radiofrequency (RF) energy that must be complied with in the siting of cellular base stations and other transmitters. In the United States, the relevant limits are those of the Federal Communications Commission (FCC). Cellular base stations use low-powered transmitters, and RF signal levels are invariably below FCC limits at any distance more than a few feet from the antennas. Thus it is entirely feasible to locate cellular base stations on rooftops of apartment buildings and to locate communications towers within residential areas and indeed these are both common practices. Local zoning ordinances are a different story. Local governments commonly restrict the location of communications towers through zoning ordinances, and they may have provisions that restrict cellular base stations in residential districts. Local attorneys or government officials should be consulted for advice about local requirements, which vary greatly among jurisdictions. Kenneth R. Foster Professor, Department of Bioengineering University of Pennsylvania

    Click the link to add information to this solution:
    THERE ANY STANDARD FOR A DISTANCE BETWEEN CELLULAR BASE STATION AND RESIDENTIAL AREA?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.