If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

Probably.

Click the link to add information to this solution:
Are there supposed to sockets on the breakout board I picked up yesterday?

The USB port located on the parallel 5 axis breakout board is for powering the board. There is no communications related to this port.

Click the link to add information to this solution:
What is the usb port for on the 5 Axis Breakout Board with Relay ($28.50)?

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT'S THE DIFFERENCE BETWEEN PARALLEL BREAKOUT BOARD AND USB ITERFACE?

The 5V power required for the breakout board can be a simple USB male to male cable, that will connect from your computer to the board itself.
Now adding a external power supply make sure that it does not exceed a total of 5V and the standard 500 MilliAMP - 1 A.

Click the link to add information to this solution:
I have a YDH-18-5 Power Supply AC Input:100-240v 47-63Hz, Ouput: 5v - 2A and need to know if its safe to use with the Parallel Breakout Board.

The parallel is the most versatile breakout board we have and will work with most of the software out there, but many computers are not equipped with parallel connectors anymore. Parallel adapter cards are available if you don't have a parallel connection on your computer.

The USB interface must be used only with the planet-cnc software, which is great software, but you are still limited to only that software application. This is actually the least expensive option unless you use linux and go with the above option.

Click the link to add information to this solution:
WHATISTHE DIFFERENCE WTIH THE PARALLEL BREAKOUT BOARD AND USB BOARD?

The instructions to connect the USB CNC Interface for the blackTooth Laser Cutter and engraver can be found on instruction #18 on thispage: https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx

Click the link to add information to this solution:
Are there any instructions for use the USP breakout board for a CO2 laser?

The breakout board does not require software to run, specifically. The breakout board serves only as a signal conditioner where the input signal from the computer is output at the corresponding terminal, or the terminal receives a signal and is conditioned and sent to the parallel connector to be read by the computer. As long as the software can communicate to the parallel port of the computer, then the breakout board will function.

Click the link to add information to this solution:
Do the 5 Axis Breakout Board with Relay requires software to setup

If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch

Click the link to add information to this solution:
IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?

These boards are compatible with Mach3 only at this time. We will be adding a Mach4 board in the near future.

Click the link to add information to this solution:
Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

Yes, the 5 axis breakout board is a very suitable replacement and also contains a relay for spindle/router control which is not on the C10 board.

Click the link to add information to this solution:
I have propably blown my C10 breakout board. This is no longer available in your parts list. Is the 5 Axis Breakout Board with Relay a suitable replacement?

The instructions on how to do this are found here, in these two videos, http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx

Additional Information:

Click the link to add information to this solution:
HOW DO I CONNECT A TOUCH PLATE TO THE BREAKOUT BOARD?

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

CP+ to COM
CP- to STEP
CP+ to CW+ (small jumper wire)
CW- to DIR

Additional Information:
If the driver does not have CP or CW labels, the CP is Step and the CW is Direction or DIR. If you connect the 5v to CP+ (or Step+) and CW+ (or DIR+) and the pin to CP- (or Step-) and another pin to CW- (or DIR-), then in software, the configuration for the step on that axis must be active low. Otherwise, if you connect the GND to CP- (or Step-) and CW- (or DIR-) and the pin to CP+ (or Step+) and another pin to CW+ (or DIR+), then in software, the configuration for the step on that axis must be active high.

Additional Information:
If you have a driver that is labeled pul, dir and ena: Pul+ is the Step+ and Pul- is the Step-. Pul is short for pulse. A pulse will create a step. Don't worry about the enable terminals.

On the x-axis, pin #2 can go to pul- and pin #3 can go to dir-. The 5v will go to pul+ and dir+. The configuration for each axis for step will be active low and toggle active low for the dir on each axis to make it go in the direction desired.

Additional Information:


Additional Information:


Additional Information:


Additional Information:

Click the link to add information to this solution:
HOW DO I WIRE FROM THE BREAKOUT BOARD TO DRIVER?

Are you using Mach3 or Mach4?

Additional Information:
using Mach3

Click the link to add information to this solution:
[816] PLS HELP ON TEST MODE THE LED DO COME ON BUT THERE IS NO MOVEMENT ON THE Z AXIS

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

The dimensions for our USB breakout board are:

L: 2.745"/ 69.723mm
W: 2.244"/ 56.9976mm
H: .501"/ 12.7254mm

Currently we do not have a CAD model on hand.

Click the link to add information to this solution:
What are the overall dimensions of the USB interface board? Is there a CAD model available?

No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I HAVE A 2000 WK 11–3 Z LIMIT SWITCHES GOING TO C10R10 BREAKOUT BOARD . CAN ALSO USE THEM AS MY HOME POSITION WELL. NEED THE WIRING CONFIGURATION

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I have the usb breakout board https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-USB-Controller-Breakout and need to run the A axis as a slave the software greys out the box how do I fix this?