The USB controller will only work with the Planet-CNC software. This software is well made and will provide great functionality. The planet-cnc software delivers instructions to the microcontroller on the board and the microcontroller will send out the pulse trains needed to move the machine correctly.

There are two main alternatives if you want to use the mach3 software:
First, get a parallel port card and add it to your computer and get a parallel breakout board. If you have a laptop/notebook computer, this will not be possible.
Second, if you have a laptop, or really want to use the USB as the main interface for controlling the machine, you will need to get the smoothstepper board which works with mach3. The price combination is much higher than the USB controller with planet-cnc, but will work with Mach3.

Additional Information:


Additional Information:


Additional Information:
The planet cnc controller can be prone to electrical interference and has been known to cause such problems. In the first instance try to use a quality double sheilded USB cable, hopefully this will fix your problem. Alternatively you may need to sheild your limit switch, estop and or motor cabling. My pick is that a quality USB cable will fix it though, worked for me.

Click the link to add information to this solution:
I have your USB controller sitting here and want to control it with something other than PlanetCNC control software?

You can only use the planet-cnc interfaces with the PlanetCNC software. If you like the software and want to remain with that software, the hardware interfaces will need to be purchased from the planet-cnc folks.

I would recommend using the Pokeys57CNC interface which is compatible with Mach3 and Mach4. You can also consider the Mach3 USB interface if the Pokeys57CNc interface is out of your price range.

Pokeys57CNC product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have registered version of planetcnc software that I purchased with a Chinese controller I want to use 3 better drivers with a separate USB controller can you recommend a controller and how to link my existing software. Regards Lloyd from Australia

The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
Hello there, I am a beginner in trying to control a stepper with a pc, you can sell me a kit to control my motor from the pc. I already have a motor, driver, and power supply

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The usb controller will only work with the planet-cnc software which is software that will work in Windows.

Click the link to add information to this solution:
Does USB Controller Breakout support Linux Ubuntu and does the software support command line interface (to control it with python scripts for example)

The usb controller will only work with the planet-cnc software which is software that will work in Windows.

Click the link to add information to this solution:
Does USB Controller Breakout support Linux Ubuntu and does the software support command line interface (to control it with python scripts for example)

Our electronics and plug and play systems can be used with any industry standard software, including but definitely not limited to the Vectric line of software.

Click the link to add information to this solution:
I am getting ready (within a week) to purchase your lug in play controller kits... The software I want to use is Vectric. I notice you talk about Mach software and sketch up. Be fore I purchase I want to make sure I can use what ever software I want... Thank you for your time. Pam

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

We offer a laser/spindle Z-axis attachment for our 4x8 greenBull CNC. The blackFoot 4x8 does not have a large enough gantry to accommodate the 40W laser tube.

Additional Information:


Additional Information:
We do sell the parts to convert your CNC milling machine to a laser, but you will need to develop the mounts that will hold all of the laser parts to the machine, if the machine was design and built by you.

We can offer guidance for this conversion.

The laser parts can be found here:
https://www.buildyourcnc.com/LaserComponents.aspx

Click the link to add information to this solution:
I already built a 4 x 8ft carving machine, I would like to modify for laser cutting wood. Do you sell a conversion kit? I use Mach3 software and steppers. Thanks Ray

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

The Planet CNC Software will require purchase after the trial version is completed, and will be purchased through their website. Currently that is the only software available for the USB Controller.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Must I have licence to run planetpc software, is there any other software that will run the usb controller

We could not guarantee, nor say, whether or not your current software would be able to utilize the USB breakout board. Our USB breakout board is designed for use with Planet CNC software found here, http://www.planet-cnc.com/index.php?page=software

As far as we know, this is the only CNC Controller software that operates on a USB breakout controller.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I want to change my old DSP controller and break out board with new one in your site that support usb it is possible ? if yes can we contact us to talking about details ?

Yes, the redLeaf plug-and-play CNC electronics can include a THC (Torch Height Controller) and motors of any size. The limit of the number of motors that this package can include is 8 motors in total.

Click the link to add information to this solution:
Will the redleaf package allow me to run a torch height controller and 2 nema 34 motors for my gantry? I would prefer to have motors on both sides of the machine with a heavy gantry

The bluchick CNC router is a perfect small format CNC that can handle most jobs. Please check here to see the latest information on this CNC router. blueChick CNC Machine. The machine can be purchased assembled. Al you will need is a computer and spindle.

Click the link to add information to this solution:
I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

You can find instructions for the Mach3 USB here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

You will probably need to use the Mach3 USB board with Mach3. We have not tested the Mach3 usb card with Mach4.

Click the link to add information to this solution:
Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.

If you would like to add a laser to a plasma table, you will need the following parts:

Laser tube at 40 watts:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Tube-CO2-40Watt

Mirror mounts (this will depend on the way you mount the laser tube):
https://www.buildyourcnc.com/item/Laser-Component-Mirror-Mount-20mm

Mirrors for the mirror mounts:
https://www.buildyourcnc.com/Item/Laser-component-20mm-mirror-25mm

Laser Tube Power Supply:
https://www.buildyourcnc.com/item/Laser-Component-Power-Supply-CO2-40W

Laser Focus Lens:
https://www.buildyourcnc.com/item/laser-component-20mm-lens-2-inch-50!80mm

Mirror and Lens Mount and Nozzle:
https://www.buildyourcnc.com/item/Laser-Component-Nozzle-20mm-lens-mirror

High Tension Extension Cable:
https://www.buildyourcnc.com/item/Laser-component-Power-Supply-High-Tension-extension-wire

Laser Control System:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System

Screw Posts (to connect the high tension and return wire to the laser tube, highly recommended as the leads on the laser tube are fragile):
https://www.buildyourcnc.com/item/laser-component-newbiehack-connectors-screw-terminal-binding-post

Safety Eyewear for CO2 laser wavelength:
https://www.buildyourcnc.com/item/laser-components-goggles-safety-tinted

Click the link to add information to this solution:
I have an Eagle Plasma table and I want to add a 40 laser. Can you supply me a list of what I need to make this happen.

Dealing with our scratch Build kit/BYO CNC Book Kit, you will use our basic 3 axis electronics kit (https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo). Now dealing with the Breakout Board, the book specifies the parallel port BoB, but you can use the USB BoB and use Planet-CNC rather than using Mach 3 or Linux-CNC as your control software.

Click the link to add information to this solution:
Correct kit of motors and electronics, I bough a book in Amazons kindle to build a CNC, this book mention a kit of motors and electronics for parallel port, I want to use USB, can you suggest me the correct kit fot this machine.