If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
I have a parallel. breakout board. and no parallel port at the back of my computer do those parallel. cards. work with the breakout board?

I don't see why Mach3 under windows 64-bit wouldn't work with an interface that uses USB as it's primary communication method. I am a bit vague on this, so I will do more research on it.

We recommend Mach3 run under Windows 32-bit when using the parallel interface as this is a legacy function.

Additional Information:


Additional Information:
mach 3 usb board setup

Additional Information:
I am running Mach3 under Windows 7 Pro 64bit without any problems.

Additional Information:


Additional Information:


Additional Information:
Are you also able to use the parallel port as your controller on the WINDOWS 7 64bit OS?

Additional Information:
Are you also able to use the parallel port as your controller on the WINDOWS 7 64bit OS?

Additional Information:
Are you also able to use the parallel port as your controller on the WINDOWS 7 64bit OS?

Additional Information:
Are you also able to use the parallel port as your controller on the WINDOWS 7 64bit OS?

Click the link to add information to this solution:
Will the Mach 3 USB breakout board work with a Windows 7 64 bit system?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

You can find the cnc machine interface board here that works with Mach4:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This board will work with Mach3 and Mach4. The board is filled with a wealth of options and features, including the ability to connect up to 8 axes (motor drivers), pendant, LCD, many outputs and inputs, separate pins for limit switches , 2 relays, Ethernet and USB interfacing.

Additional Information:

Click the link to add information to this solution:
Do you have a breakout board that will work with Mach4?

The breakout board will work with 3.3 volt parallel port. The integrated circuits on the board bring the level up to 5 volts for each pin when engaged. The breakout board is powered from the USB port and this is where the 5 volts is acquired.

Click the link to add information to this solution:
Does your breakout board work with low voltage 3.3volt parallel ports?

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router

A parallel to USB adapter will not work. You will need to use a USB interface like the ones below:

Mach3 USB interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Poeys57CNC Interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Additional Information:
To answer the question in more detail, the parallel port is actually an extension straight from the CPU and is also called the GPIO (General Purpose I/O) pins. These pins carry signals independently, hence the description as being a parallel port.

The stepper motor driver receives a pulse train (series of pulses). A single pin on the parallel port sends a pulse train to one stepper motor driver and stepper motor for a single axis. Another pin on the parallel port sends a pulse train to another stepper motor driver on another axis. This happens simultaneously as with the direction signals for each axis.

If a parallel port is adapted through a USB (using an adapter), the parallel port cannot have these signals happen in a simultaneous fashion and will cause the stepper motors of a CNC router or machine to be very clunky, if it works at all. To elaborate, the computer sends an instruction to the USB to send a high signal to pin 1, so it does, then another signal to pin 2, so it does. This is happening one after another. The speed at which this happens is reduced dramatically, and the position of one axis may now be out of sync to another axis.

The reason the USB interfaces (linked above) work is that the USB delivers broad instructions to the interface (to a microcontroller) and the interface parses the instructions and outputs simultaneous signals to the stepper motor drivers.

Hope this helps.

Click the link to add information to this solution:
My computer doesn't have a parallel port connection. Can I use a usb to parallel port cable to communicate with my breakout board?

The 5V power required for the breakout board can be a simple USB male to male cable, that will connect from your computer to the board itself.
Now adding a external power supply make sure that it does not exceed a total of 5V and the standard 500 MilliAMP - 1 A.

Click the link to add information to this solution:
I have a YDH-18-5 Power Supply AC Input:100-240v 47-63Hz, Ouput: 5v - 2A and need to know if its safe to use with the Parallel Breakout Board.

Yes, you can select the price option for the electronics combos that include the interface board you desire.

Go to the electronics category page:
https://www.buildyourcnc.com/electronicscombo.aspx

Select the motors and drivers combination you desire and select the price option that contains the interface card you desire.

Click the link to add information to this solution:
Does your 3 axis comboi have the same controller board (i.e. parallel option) as the 4 axis combo?

Yes, the 5 axis breakout board is a very suitable replacement and also contains a relay for spindle/router control which is not on the C10 board.

Click the link to add information to this solution:
I have propably blown my C10 breakout board. This is no longer available in your parts list. Is the 5 Axis Breakout Board with Relay a suitable replacement?

Yes, here is the URL for the parallel breakout board that we sell:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
can I purchase just the parallel controller board? I purchased the usb option 4 axis combo and would like to also try the system with my parallel port computer. Any help with this will be greatly appreciated; my goal is to implement mach4.

These boards are compatible with Mach3 only at this time. We will be adding a Mach4 board in the near future.

Click the link to add information to this solution:
Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

Unfortunately no. The parallel port allows for digital signals to be output from 17 pins simultaneously (in parallel). Parallel port adapters tries to achieve this by receiving instructions in a two wire (USB) data signal and convert that to 17 disparate signals. This type of data transmission is too slow for the drivers of a CNC machine or router.

Click the link to add information to this solution:
can i use a usb to parallel port adapter to connect breakout board to computer? (using mach 3)

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am installing a mach 3 usb controller into a wright cnc plasma table and I need instruction on wiring the thc (proma compact ) torch height controller to this board. IE will this board work to replace the parallel port board with usb controller board?

The USB on the Parallel breakout board, is used for powering the board itself (5v USB), and the Parallel to communicate directly between the drivers and the computer/mach 3.
Planet-CNC cannot be used with our Parallel Breakout Board, it is only intend to be used with Mach 3/other open source programs.

To use Planet-CNC, please refer to our USB breakout board! (https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout)

Click the link to add information to this solution:
can I use the usb on the parallel breakout board with planet cmc

The mapping of the input pins of the parallel breakout board is configured through software. The input pin are very versatile and can be mapped to all kinds of different types of input including axis limits and axis homing.

Click the link to add information to this solution:
Is there a mapping on the input (switch) pins to an axis on the parallel breakout board?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

Yes, the Mach3 USB controller will work with the latest Windows version and in 64-bit mode. The 32-bit mode is only relevant for using the parallel port driver if you are using a parallel port breakout board. Since this controller is connected via a USB cable, the 64-bit state will work fine.

Additional Information:
mach3 not showing in device manager

Click the link to add information to this solution:
[575] I have a 64 bit Windows 11 laptop. Will this interface board work with this? If not is there an option you can suggest.