[ Log In ]
[ Register ]

Question #: 13599

Question: Are there contour type brushes available for leadscrews and round rails

Current Solution

Yes, you can use these flexible strip brushes and create a mount for the contour that you need:

https://www.buildyourcnc.com/item/strip-brush

Respond:

Other Possible Solutions to this Question

  • DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

    We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

    Click the link to add information to this solution:
    DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

  • ARE THERE PRODUCTS AVAILABLE TO THE GENERAL PUBLIC THAT CAN BE PURCHASED PROTECT CELLULAR OR PORTABLE TELEPHONE USERS FROM RADIATION? IF SO, WHERE THESE FOUND?

    There are a number of opportunistic gadgets on the market to allegedly protect the user from hazards of cellular phones. You can search the Internet to find the latest, ranging from antenna shields to whole-body shielding materials. Most experts believe that these devices take advantage of customers' misunderstanding and unfounded fears to sell products with no real value. First of all, cell phones that operate within the guidelines established by national and international safety panels have never been shown to pose a health risk to the user (see answers to other questions on cell phone safety on this website). Secondly, placing any kind of shield over the antenna of a cell phone will in most cases cause it to increase its RF output as it attempts to compensate for signal loss in the shield and maintain a quality phone call. The U.S. Food and Drug Administration published an advisory on cell phones several years ago that said if you are concerned about risks of using a cell phone, then simply use it less. That is still good advice today. Gary Zeman, ScD, CHP Lawrence Berkeley National Laboratory

    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    ARE THERE PRODUCTS AVAILABLE TO THE GENERAL PUBLIC THAT CAN BE PURCHASED PROTECT CELLULAR OR PORTABLE TELEPHONE USERS FROM RADIATION? IF SO, WHERE THESE FOUND?

  • ARE THERE RECOMMENDATIONS FOR THE PREVENTION OF INSTITUTIONAL OUTBREAKS INFLUENZA?

    The most important factor in preventing outbreaks is annual vaccination of all occupants of the facility, and all persons in the facility who share the same air as the high-risk occupants. Groups that should be targeted include physicians, nurses, and other personnel in hospitals and outpatient settings who have contact with high-risk patients in all age groups, and providers of home care to high-risk persons (e.g., visiting nurses, volunteers).

    Click the link to add information to this solution:
    ARE THERE RECOMMENDATIONS FOR THE PREVENTION OF INSTITUTIONAL OUTBREAKS INFLUENZA?

  • THERE ANY STANDARD FOR A DISTANCE BETWEEN CELLULAR BASE STATION AND RESIDENTIAL AREA?

    The two main constraints on siting cellular base stations near residential areas are government exposure limits and local zoning ordinances. Various governments have limits for human exposure to radiofrequency (RF) energy that must be complied with in the siting of cellular base stations and other transmitters. In the United States, the relevant limits are those of the Federal Communications Commission (FCC). Cellular base stations use low-powered transmitters, and RF signal levels are invariably below FCC limits at any distance more than a few feet from the antennas. Thus it is entirely feasible to locate cellular base stations on rooftops of apartment buildings and to locate communications towers within residential areas and indeed these are both common practices. Local zoning ordinances are a different story. Local governments commonly restrict the location of communications towers through zoning ordinances, and they may have provisions that restrict cellular base stations in residential districts. Local attorneys or government officials should be consulted for advice about local requirements, which vary greatly among jurisdictions. Kenneth R. Foster Professor, Department of Bioengineering University of Pennsylvania

    Click the link to add information to this solution:
    THERE ANY STANDARD FOR A DISTANCE BETWEEN CELLULAR BASE STATION AND RESIDENTIAL AREA?

  • IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?

    If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

    Additional Information:
    limit and home switch

    Click the link to add information to this solution:
    IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?

  • THEY ARE ASKING FOR THE ACTIVATION CODE AND SERIAL NUMBER USB BOARD. HOW CAN GET THAT INFORMATION?

    To get the activation code, all you need to do is plug the USB board into the computer using a USB cable, go to machine -> firmware -> update. After the firmware is updated the program will present to you a dialog box containing the activation code.

    Additional Information:
    MUAR-QVXU-CAYW-CBWQ


    Additional Information:
    MUIS-RQPB-PTHB-QTTB

    Additional Information:
    MUIH-EERP-IADB-TRIP

    Additional Information:
    9zYWBVf5TxKSK7hEr8gFX3EBw5wa0AMMllQqgftIAnKvZ8DXItLxaPbOB3jWvnpczl/sM/De0scRPHfSxWGmcA==

    Additional Information:
    Key: LUQR-BQYI-SCEW-QVBT

    Additional Information:


    Additional Information:
    after i copy the code in the lower case i recived the same message (more than 8 times) ,, this is a evaluation...,, what i need to do to register properly?

    Additional Information:
    MUJR-BISM-KRDN-KKER
    056971

    Additional Information:
    0561234

    Additional Information:
    MURL-QPQU-EGBJ-FNMB

    Additional Information:
    MUCE-LFMQ-WBCW-MLHO

    Additional Information:


    Additional Information:
    LUTA-ADVJ-FXTW-FBCE

    Additional Information:
    LUTA-ADVJ-FXTW-FBCE

    Additional Information:
    looking for registration key for MUUK-IBTW-ECTL-CJWD

    Additional Information:
    MUXO-PIYY-KNHD-RKLY

    Additional Information:
    MUUE-YYCR-FCIC-VATK

    Additional Information:
    MUUE-YYCR-FCIC-VATK

    Additional Information:


    Additional Information:
    MUEY-YLJU-OBRR-LJBV

    Additional Information:
    MUSP-JFDV-EKGQ-OVLW

    Additional Information:
    MUSP-JFDV-EKGQ-OVLW

    Additional Information:


    Additional Information:


    Additional Information:
    MULY-XRYF-BBDN-FBWP

    Additional Information:


    Additional Information:


    Additional Information:
    how to generate activation code richauto a11

    Additional Information:
    MUJC-LNIL-EOHS-YKNQ

    Additional Information:
    sdfd

    Additional Information:
    m l

    Additional Information:
    MUXC-RWKB-PKAL-HGNN

    Additional Information:
    57625YY60Y7Y30X5

    Additional Information:
    57625YY60Y7Y30X5

    Additional Information:
    57625YY60Y7Y30X5

    Additional Information:
    57625YY60Y7Y30X5

    Click the link to add information to this solution:
    THEY ARE ASKING FOR THE ACTIVATION CODE AND SERIAL NUMBER USB BOARD. HOW CAN GET THAT INFORMATION?

  • ARE THERE STILL VIDEOS THAT CAN WATCH AS PUT THIS TOGETHER, I'LL BUY THEM IF HAVE TO, VERY FUSTURATED WITH ELECTROCTICS AND WIRING PART.
  • I WOULD LIKE TO KNOW IF THERE IS A STORE OR SHOP WHERE CAN SEE THE PRODUCT AND BUY IT?

    If you are located near Houston, Texas area you can stop by our shop. If you are not near us, you can check in our forums, and see if you can find someone in your area that has one of our machines, and would be willing to let you come see it in action.

    Click the link to add information to this solution:
    I WOULD LIKE TO KNOW IF THERE IS A STORE OR SHOP WHERE CAN SEE THE PRODUCT AND BUY IT?

  • WHAT ARE CURRENT RECOMMENDED IEEE EMF OCCUPATIONAL EXPOSURE LEVELS AND GUIDELINES FOR RADIO BASE STATION ANTENNAS?

    The following answer assumes "radio Base Station Antennas" refers to base stations used for personal wireless communications services such as cellular telephone, Personnel Communications Services (PCS), and Enhanced Specialized Mobile radio (ESMR). In the United States, the frequency band allocated for base stations used for personal wireless communications is 869-894 MHz for cellular service, 851-866 MHz for ESMR, and 1930-1990 MHz for PCS. The IEEE exposure limits (maximum permissible exposure—MPE) for occupational exposure (controlled environments where exposures may be incurred by persons who are aware of the potential for exposure) are frequency dependent and are expressed in terms of incident power density. The appropriate value to compare with the MPE is the incident power density averaged over the vertical cross-section of the human body. The occupational exposure limits are also time-averaged over any six-minute interval. The IEEE C95.1-1991 MPE values are shown in the table below:
    IEEE C95.1-1991 Maximum Permissible Exposure (MPE) Values
    Frequency Band Power Density
    General mw/cm2 W/cm2
    851-866 MHz f/300 mW/cm2 2.84-2.88 28.4-28.8
    869-894 MHz f/300 mW/cm2 2.90-2.98 29.0-29.8
    1930-1990 MHz f/300 mW/cm2 6.43-6.63 64.3-66.3
    NOTE: f is in MHz
    As indicated above, these values are for continuous exposure (t > 6 minutes) and are to be compared with the spatial average of the incident power density. all base stations used for personal wireless telecommunications services in the United States are required to comply with the FCC limits (as mandated by the Telecommunications Act of 1996). The FCC limits are based on a hybrid of the IEEE limits and the 1986 recommendations of the National Council on Radiation Protection and Measurements. The FCC MPEs are the same as the IEEE values for frequencies below 1500 MHz but are capped at 5 mW/cm2 (50 W/cm2) for frequencies greater than 1500 MHz.

    Both the FCC and IEEE MPEs for exposure of the public (uncontrolled environments) are one-fifth of the above values. As above, the value to compare with the MPE is the incident power density averaged over the vertical cross-section of the human body. The averaging time for the general public is 30 minutes. Thus, for transient exposures lasting six minutes or less, the MPEs for occupational exposure and exposure of the general public MPEs are the same. For cases of simultaneous exposure from antennas operating in different frequency bands, the ratio of the spatially averaged incident power density in each frequency band to the corresponding MPE for that band is determined and the sum of all such ratios must be less than unity in order to comply.

    R. C. Petersen
    Manager, Wireless and Optical
    Technologies Safety Department

    Click the link to add information to this solution:
    WHAT ARE CURRENT RECOMMENDED IEEE EMF OCCUPATIONAL EXPOSURE LEVELS AND GUIDELINES FOR RADIO BASE STATION ANTENNAS?

  • WE ARE ALWAYS CONCERNED THAT THERE WON'T BE ENOUGH VACCINE TO VACCINATE OUR PATIENTS IN THE FALL. WHAT CAN DO ASSURED WE'VE DONE ALL POSSIBLY AVOID THIS TYPE OF SITUATION?

    It is never too early to begin planning for the coming fall's influenza vaccination program. The most important thing you can do initially is to place your order for vaccine from your usual source. Some manufacturers often stop taking pre-orders in mid-May. Be sure to include vaccine for pediatric patients needing two doses and also for your facility's healthcare workers as part of your overall campaign.

    Click the link to add information to this solution:
    WE ARE ALWAYS CONCERNED THAT THERE WON'T BE ENOUGH VACCINE TO VACCINATE OUR PATIENTS IN THE FALL. WHAT CAN DO ASSURED WE'VE DONE ALL POSSIBLY AVOID THIS TYPE OF SITUATION?

  • WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

    You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

    Additional Information:
    wire size

    Click the link to add information to this solution:
    WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

  • HOW MUCH RADIATION GIVEN OFF BY A CELL PHONE AND THERE ANY WAY TO STOP THE FROM BEING ABSORBED INTO YOURSELF?

    Portable cell phones emit about 0.6 watts of radiofrequency energy, limited primarily by the power of the battery. As with any radiofrequency transmitter, there will be some amount of absorption in the human body; the amount depends on how close you are to the antenna. The Federal Communications Commission (FCC) limits the amount of radiofrequency energy which cell phones can deposit in the body to levels at which no health effects are to be expected. See an article on Cell Phone Safety on this website for more information.

    Gary H. Zeman, ScD, CHP

    Click the link to add information to this solution:
    HOW MUCH RADIATION GIVEN OFF BY A CELL PHONE AND THERE ANY WAY TO STOP THE FROM BEING ABSORBED INTO YOURSELF?

  • WHAT ARE THE BLACKTOOTH LENS SIZES AND FOCAL LENGTH SPECIFICATIONS?

    The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

    The mirrors are 25mm wide mirrors.

    Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.

    Click the link to add information to this solution:
    WHAT ARE THE BLACKTOOTH LENS SIZES AND FOCAL LENGTH SPECIFICATIONS?

  • WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

    Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

    Additional Information:

    Click the link to add information to this solution:
    WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

  • SIGNAL AND 5V POWER WIRING DIAGRAM FOR RELAY USB BR ABOUT BOARD.

    Here is the wiring diagram for the MAch3 USB breakout board:
    https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

    You will need 24 volt relays for the output on that board since that side of the board requires 24 volt power at the V+ and V-

    Customer Response:
    My inquiry is for the Planet CNC USB and 5v relays.
    I am 99% finished with my 2 axis lathe build and this is the last item for me to conquer.
    I want to control power to router, and vacuum with the BOB going through the 5V relays purchased on this site.
    Thanks again.

    Using the Mist, spindle or flood pins...

    Buildyourcnc response:
    There is an IN, GND and 5V for the digital side to engage the relay. There is an S, O and P for the power line of the device to be controlled.

    The 5V and GND must be connected to the 5V and GND from the USB board. The IN is the wire from the output terminal (i.e. mist, flood, spindle).

    For the power side, here are the scenarios:
    - P to O connection is normally open
    - P to S connection is normally closed

    So, if you have the power wire that would plug into the wall, the L "black" wire from the power cord will pass through this part of the circuit (cutting the wire and one end in the P terminal and the other end in the O or S terminal). Generally, the P to O is used as this connection is normally open and when the relay is engaged, the circuit will close allowing the current to flow through that wire.

    Click the link to add information to this solution:
    SIGNAL AND 5V POWER WIRING DIAGRAM FOR RELAY USB BR ABOUT BOARD.

  • WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

    Shipping crate size 121" X 36" X 92"

    Weight 511 LBS

    Click the link to add information to this solution:
    WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

  • DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

    The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

    Additional Information:

    Click the link to add information to this solution:
    DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

  • WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

    You can expect a two week lead time for the redFrog pick and place machine.

    Additional Information:

    Click the link to add information to this solution:
    WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

  • WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

    Shipping crate 121" X 36" X 92"

    Weight 511 LBS

    Additional Information:
    ship in india pls

    Additional Information:
    International shipping rates can be determined by:
    - adding products to the cart
    - go to the cart and enter shipped by address
    - and pressing the calculate shipping button

    Click the link to add information to this solution:
    WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.