I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

Red is A+
Blue is A-
Black is B+
and Green is B-

Click the link to add information to this solution:
I purchased the 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller and the motors supplied only have 4 wires coming out of them (R,G,B,Blk). Your wiring video shows wiring 8 cables. do you have a video showing how to wire the 4 wire version?

There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

Click the link to add information to this solution:
I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

Click the link to add information to this solution:
I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

We currently do not sell any plan's for any of our machines, only for our scratch and build kit.

Click the link to add information to this solution:
Would you sell a kit that has all of the hardware and electronics with CNC plans for the table and gantry? Some of have access to a CNC temporarily (TechShop) but want one of our own.

Controlling a 3-axis or 4-axis motor configuration, you will need the following items drivers/motors/controller. Our electronics combo comes with the items mentioned and with power supply/miscellaneous items.
The only other item needed will be a computer (with controller software) to communicate and view controls of your motors.
Using the Parallel breakout board will use Mach 3 software, and USB will use Planet-CNC software.

Additional Information:
You can use this link to see the videos on how to connect the electronics together and make them work: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
hey, where can i see the steps how can i control 3 or 4 step motor? can i use the Axis Electronics Combo? or i need to connect controller?

Yes, you can use the 4 axis kit and use two of the motors on the gantry. You will need to wire the gantry axis motors to the same step and direction signals on the controller interface. For example, if the gantry axis is the X axis, then on the controller step and direction terminals (CP and CW) is wired to both of the stepper motor drivers for the X axis.

Click the link to add information to this solution:
4 axis kit can I use 2 motors for the gantry with one controller card? or I buy the 3 axis kit instead?

At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

Click the link to add information to this solution:
Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

The parallel breakout board will support up to 5 axes.

Click the link to add information to this solution:
Regarding the heavy gantry electronics combo. When choosing the parallel breakout board option, how many axis/motors does the breakout board support? Thank you!

The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

The 651 oz/in NEMA 34 stepper motor does have a dual shaft. The shaft extends 19 mm at both ends.

Click the link to add information to this solution:
in the 3 Axis Electronics Combo (For Heavy Gantry) the 651oz motor is a dual shaft ?

This version of the blueChick comes with the Parallel Breakout Board.

Click the link to add information to this solution:
Which electronics unit comes with item #230, the 3 axis USB or parallel? If parallel, do you have a package price that includes the USB electronics?

The diagram for wiring the USB interface board is located here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

Under the board illustration, there are three smaller diagrams of limit switch wiring. On each, there are two connections, the GND and the pin which are labeled at the ends of the circuit on the diagrams. The pin side would go to the axis label ++ or -- terminal (i.e. X++, or X--). The other end, labeled GND would connect to any ground terminal on the board.

Click the link to add information to this solution:
I am using 5 limit switches on my 3 axis machine. I am using the usb controller for planet cnc. I would like to know where all the wires related to the limit switches get connected? A diagram would be helpful.

Yes, the redLeaf plug-and-play CNC electronics can include a THC (Torch Height Controller) and motors of any size. The limit of the number of motors that this package can include is 8 motors in total.

Click the link to add information to this solution:
Will the redleaf package allow me to run a torch height controller and 2 nema 34 motors for my gantry? I would prefer to have motors on both sides of the machine with a heavy gantry

These boards are compatible with Mach3 only at this time. We will be adding a Mach4 board in the near future.

Click the link to add information to this solution:
Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

Additional Information:


Additional Information:
Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

Click the link to add information to this solution:
IS THE MACH3 SOFTWARE COMPATIBLE WITH 3 AXIS MOTION CONTROL COMBO KITS? PLANET CNC MENTIONED AS BEING COMPATIBLE.

What is the weight of the gantry, number of teeth on the drive sprocket and tooth pitch?

Click the link to add information to this solution:
I build a 3 axis router CNC the gantry is heavy in aluminium plate, witch plug n'play kit you suggest me 1 or two motor on the longest axis this will be drive with chain?

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
What else to I need to purchase along with the "3 Axis Electronics Combo w/ USB Interface Board" to get the electronics up and running? (software, 5V power supply, 4-conductor wire, etc.)