You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
Do you have the data sheets for the motors so that I can use the dimensions in my model?

We currently do not sell any plan's for any of our machines, only for our scratch and build kit.

Click the link to add information to this solution:
Would you sell a kit that has all of the hardware and electronics with CNC plans for the table and gantry? Some of have access to a CNC temporarily (TechShop) but want one of our own.

Red is A+
Blue is A-
Black is B+
and Green is B-

Click the link to add information to this solution:
I purchased the 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller and the motors supplied only have 4 wires coming out of them (R,G,B,Blk). Your wiring video shows wiring 8 cables. do you have a video showing how to wire the 4 wire version?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

The blackToe 2'x4' cnc machine is sold as a kit only. We offer plans for the scratch (book) build machine that can be found here for purchase and also comes with a DVD showing the build process: http://www.buildyourcnc.com/cnckitintro.aspx and the plans for build in the book is on the CNC book page: http://www.buildyourcnc.com/Book.aspx.

You can use the same size stepping motors referenced in the book: http://www.buildyourcnc.com/category/elcombo

Click the link to add information to this solution:
I would like to build the 2’x 4’ blackToe2x4v40 CNC router. I have your book. I want to build the latest model blackToe2x4 v40. Are those the correct plans on your web book page ? Is there a bill of materials? If I use a Porter Cable 3-3/4 router motor what size stepper motors do I need?

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I am making my own CNC setup using all the electronics from your website and I have many questions. Please advise how to have my computer recognize the USB connection from my breakout board also I would like to use a water cooled spindle but I need to know the parts required for a 4x10 bed area used for woods and plastics

This is a good video on how to do a vacuum table

Click the link to add information to this solution:
Do you have any videos or plans for how to make a strong table for a large CNC router? I saw the torsion box videos but would like some more guidance on how to build just a good table.

Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I am looking at one of your electronics packages as a replacement for my excisting electronics. I have a old table top CNC that has a bad electronics pack, but the motors, and the mill are in good shape. could your system be adapted to work in this case?

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

If you would like to come to the office, please call the office at 281-815-7701 to request a visit at your specified time within our business hours so we can make sure that the right person will be there to assist you.

Click the link to add information to this solution:
I am considering the purchase of a Black foot or Green Bull CNC router and would like to come and visit your facility to see them in person and to discuss my requirements. Please can you tell me your address. I am based in NW Houston. Many thanks.

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

Considering enlarging the machine, might have its down sides do to the structural integrity of the scratch build machine. Primarily by making the width longer it will start to sag in the center, which will lead to having to redesign the gantry to be more structurally rigid to support the added length. Which then will increase the weight and height of your gantry to support the add size, which will always end up to creating a larger CNC.

We usually do not recommend modifying the scratch build CNC, due to the very limited capabilities, and the structural design of the scratch build. We also do not recommend using longer than 48" ACME screw/leadscrew due to the increasing chance of warping and bending in the ACME screws/leadscrew in the given length.
We do recommend modifying the CNC machines we sell to accommodate the added requests that some of our customers desire, but you will be limited to the width of the gantry with our machines.

Click the link to add information to this solution:
I've read your book and I'm looking to purchase the hardware kit with DVD as well as an electronics kit. I would like my machine to have a working area of at least 24" wide by 48" long. Can I just make the bed (and gantry) wider to accommodate larger priceslike 30"x60"? If so what electronics kit would you recommend?

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

The motor is helped by the mechanical leverage of the screw. The 425 oz-in motors that are included in the standard electronics combo has very high torque for that type of machine. You will have no problem using that motor for the book machine.

We use that motor for very heavy spindles on the blackToe and blackFoot CNC Machine kits.

You will need to do the mechanical leverage calculation along with the torque of the motor to determine the actual weight it will lift. The calculation will need to consider the type and pitch of the screw and it would also consider the gravity constant of 9.8 m/s/s.

If you need me to determine this formula and work out the calculation based on the screw you are using, please let me know.

Additional Information:
thank you for the reply. I would be really good to know the calculation. The lead screw is 1/2" diameter with 13 TPI. Please provide the calculation. And one more question. If I am cutting 18mm MDF with 6mm cutting bit (so 6mm pass), what can be the maximum speed rate of cutting and spindle speed of router?
thank you

Click the link to add information to this solution:
I received the electronics for book build cnc machine. I need to know how much weight the z-axis motor can hold since my (craftsman) router seems to be heavy. It is 2HP with variable speed

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
I am building the CNC in your book - Build you own CNC Machine. One of the bearing thicknesses is 1/4" I can't find that bearing online. I can find 9/32, will that be a problem. Do you have a source? Thx

Yes, servo motors can be mounted on this machine. If the mounting dimensions are different than NEMA 23 or NEMA 34, then all you need to do is keep the center of the motorshaft with the center of the bearing location and locate the mounting holes for he servo you wish to use. Most industrial servos used for these machines share the same mounting dimensions and NEMA specifications.

Additional Information:
This machine is one of the most customizable machines out in the wild. Customers of these machines have fashioned many modifications to suit their needs.

Additional Information:
20

Click the link to add information to this solution:
[796] Hello. To what extent can the design plans be customized? For example, if I wanted servo motors instead of steppers? That would requirements for motor mounting, controls, and electrical. Thank you.

Dealing with our scratch Build kit/BYO CNC Book Kit, you will use our basic 3 axis electronics kit (https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo). Now dealing with the Breakout Board, the book specifies the parallel port BoB, but you can use the USB BoB and use Planet-CNC rather than using Mach 3 or Linux-CNC as your control software.

Click the link to add information to this solution:
Correct kit of motors and electronics, I bough a book in Amazons kindle to build a CNC, this book mention a kit of motors and electronics for parallel port, I want to use USB, can you suggest me the correct kit fot this machine.

Yes, the redLeaf plug-and-play CNC electronics can include a THC (Torch Height Controller) and motors of any size. The limit of the number of motors that this package can include is 8 motors in total.

Click the link to add information to this solution:
Will the redleaf package allow me to run a torch height controller and 2 nema 34 motors for my gantry? I would prefer to have motors on both sides of the machine with a heavy gantry