We currently do not sell any plan's for any of our machines, only for our scratch and build kit.

Click the link to add information to this solution:
Would you sell a kit that has all of the hardware and electronics with CNC plans for the table and gantry? Some of have access to a CNC temporarily (TechShop) but want one of our own.

Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I purchased the original instructions about 3 years ago and successfully built that device. Now I am looking at the 13X36 Bluechick base kit. Will all my original electronics work with the new kit? Is there a parts list that you could send me for the 13x36 Kit?

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

This would totally work for that application. This cable carrier is used for any object that needs to move and carries some electrical or tubing within it. This cable carrier is great for cable management where you want to make sure the wires and tubes are in a position that you set, not where the wires and tubing want to go.

Click the link to add information to this solution:
[311] I am looking to use this type of thing with a pipe for theater. Where the pipe can be lowered and it would have electrical and signal cable inside. Is this good for that or should I look at something else?

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
Is it possible to buy just the electronics and hardware for the bigfoot along with the plans for the timber components so that I could have them cut here in the UK and reduce the amount of material that needs to be shipped?

We may be able to source those motors. Curious, the 6000 oz-in motor is pretty big. Do you mind explaining the application of the CNC machine and the structure that would require the large motor?

Additional Information:
The largest motors we can offer is 3900 oz-in without any mechanical help. 6000 oz-in can be resolved by mechanical means as an alternative.

Click the link to add information to this solution:
I am converting a 12x36 lathe over to CNC, I am interested in a 2 axis kit. I would love one stepper motor to be no smaller than 1200oz. , and another at 6000z. Is this something that you could offer? I have two other cnc machines but this is my first converstion on my own.

Considering enlarging the machine, might have its down sides do to the structural integrity of the scratch build machine. Primarily by making the width longer it will start to sag in the center, which will lead to having to redesign the gantry to be more structurally rigid to support the added length. Which then will increase the weight and height of your gantry to support the add size, which will always end up to creating a larger CNC.

We usually do not recommend modifying the scratch build CNC, due to the very limited capabilities, and the structural design of the scratch build. We also do not recommend using longer than 48" ACME screw/leadscrew due to the increasing chance of warping and bending in the ACME screws/leadscrew in the given length.
We do recommend modifying the CNC machines we sell to accommodate the added requests that some of our customers desire, but you will be limited to the width of the gantry with our machines.

Click the link to add information to this solution:
I've read your book and I'm looking to purchase the hardware kit with DVD as well as an electronics kit. I would like my machine to have a working area of at least 24" wide by 48" long. Can I just make the bed (and gantry) wider to accommodate larger priceslike 30"x60"? If so what electronics kit would you recommend?

The motor with that model number is here: https://buildyourcnc.com/item/electronicsAndMotors-nema24-425ozin

Click the link to add information to this solution:
In looking for a stepper motor amongst old parts in my lab, I found one with a sticker that says buildyourowncnc.com and PN SM60HT86-2008BF U2 on it. I found a Q&A on your website that says it's a NEMA 24 motor with 425 oz/in holding torque. I was wondering if you were able to confirm this? Any specs sheets and details of the motor would be much appreciated

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
IT POSSIBLE TO BUY THE CAD FILES FOR BLACK FOOT MACHINE, MECHANICAL PARTS AND ELECTRONICS BUT NOT WOODEN PARTS, SAVE SHIPPING COSTS? IN THAT CASE I WOULD INSTRUCT SOMEONE MILL ME.

We do offer discounts for academic institutions and instructors. Please contact us via the phone number above to inquire about our academic discount.

Click the link to add information to this solution:
I need to know if you have prices for educators, or other ways that a teacher could procure a blackToe 2'x4' CNC router. I apologize that this is sort of a bold question, as your routers are already well-priced.

Please contact sales@buildyourcnc.com for a custom quote.

Click the link to add information to this solution:
I want to build a 4 x 4 plasma table. I am not good with the electronic parts of the system. What would you recommend as a turn key electronics package? I also want to build it with chain drive

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

The license file should be called Mach1Lic.Dat, you can copy it to a Mach3 folder on another computer and it will register the program.

Click the link to add information to this solution:
You sent my my activation code which I have jealously, guarded on my Desktop till needed, now, unfortunately I cant get it to copy from Desktop to the computer and Mach3, is it possible to get advice on this or maybe a replacement that can be put on a stick then plugged into my Mach3 computer. This is how I have tried but when I open the folder it is empty. Thanks for your patience with me.

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I am making my own CNC setup using all the electronics from your website and I have many questions. Please advise how to have my computer recognize the USB connection from my breakout board also I would like to use a water cooled spindle but I need to know the parts required for a 4x10 bed area used for woods and plastics

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

You can do raster and vector engraving on the greenBull laser/spindle combination. The methods of this process is not accomplished in the same way as the typical laser machines where CorelDRAW is used. The Mach3 laser plug-in can be used for the raster engraving and standard CNC g-code can be used for vector cutting and engraving.

The raster method will not be fast on the greenBull since the z-axis is heavy and there are inertial limitation on doing fast raster back and forth movement. Vector is the best use of this machine.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am looking at purchasing the greenbull 5X system with the laser/spindle combination. Can the laser do both rastered engraving as well as vectored cutting with the same breakout board and software? If I have this wrong please let me know what would be needed to accompish this.

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!