You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I am looking at one of your electronics packages as a replacement for my excisting electronics. I have a old table top CNC that has a bad electronics pack, but the motors, and the mill are in good shape. could your system be adapted to work in this case?

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

The available options for the blackFoot, is only structural components with hardware, and structure components/hardware with electronic components.
However we currently do not have any plans available for public use/distribution.

Click the link to add information to this solution:
I have a 4x8 CNC and would like to cut my own parts for the Blackfoot. What is the price for the plans and the electronics ?

This is a good video on how to do a vacuum table

Click the link to add information to this solution:
Do you have any videos or plans for how to make a strong table for a large CNC router? I saw the torsion box videos but would like some more guidance on how to build just a good table.

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

I would highly recommend a spindle and VFD rather than a router.

Spindles:
- Have a far longer life longer than a router. You will probably go through a few routers before the end of the spindle's life.
- Are quieter than routers
- And the water cooled spindles we stock do not blow the chips into the air. Chips are much easier to capture with or without a dust removal system.

You can find our spindles here:
https://www.buildyourcnc.com/SpindlesAndAccessories.aspx

Once you get your first spindle, you will never go back to routers. Routers are great for handrouting work, but not the best for continuous CNC milling.

Click the link to add information to this solution:
Hi there, I have a cnc table that I built but I am looking for a higher powered router because I am using the table for flattening slabs with a large straight bit. Would you have any recommendations for the type of router I should buy? Also do you sell large bits for flattening slabs?

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I am making my own CNC setup using all the electronics from your website and I have many questions. Please advise how to have my computer recognize the USB connection from my breakout board also I would like to use a water cooled spindle but I need to know the parts required for a 4x10 bed area used for woods and plastics

Unfortunately, we don't sell the planet-cnc controller anymore. They made a change to their software that prohibits us from creating the open source board.

We do sell three other boards that may work for you.

The Pokeys57CNC board is the mose feature rich and will work with both Mach3 and Mach4:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

The MAch3 USB board is a good inexpensive interface that will work well if you need the interface to be USB only:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Our in-house parallel breakout board (ytou need a parallel port for this interface to work):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay
Most motherboards have the parallel port connector on the motherboard, but not as a connector on the back of the computer case.

Click the link to add information to this solution:
Do you sell the 3 axis electronics combo , for heavy gantry , with the new Planet CNC usb controller ?

I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

Click the link to add information to this solution:
I HAVE NOT SEEN ANY REFERENCES TO STEPPING MOTOR ENCODER FEED-BACK FOR CLOSED LOOP CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
IT POSSIBLE TO BUY THE CAD FILES FOR BLACK FOOT MACHINE, MECHANICAL PARTS AND ELECTRONICS BUT NOT WOODEN PARTS, SAVE SHIPPING COSTS? IN THAT CASE I WOULD INSTRUCT SOMEONE MILL ME.

The USB interface only works with momentary switches unfortunately. If you have extensive knowledge of digital electronics, you can apply a receiver that uses a microcontroller and a transmitter with another microcontroller that produces the pulsing signal with the controls that you need.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I would like to make a handheld remote for the USB CNC Board using a joystick instead of momentary switches. Could you suggest one that will work with your board.

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

Dealing with our scratch Build kit/BYO CNC Book Kit, you will use our basic 3 axis electronics kit (https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo). Now dealing with the Breakout Board, the book specifies the parallel port BoB, but you can use the USB BoB and use Planet-CNC rather than using Mach 3 or Linux-CNC as your control software.

Click the link to add information to this solution:
Correct kit of motors and electronics, I bough a book in Amazons kindle to build a CNC, this book mention a kit of motors and electronics for parallel port, I want to use USB, can you suggest me the correct kit fot this machine.

We do offer all of the parts; but it is best to purchase them a la carte. You will probably not want the hardware since this would not conform to a design in metal.

All of the mechanical parts are available here:
https://buildyourcnc.com/CNCMachineMechanicalParts.aspx

All of the electronics you would need is available here:
https://buildyourcnc.com/electronicscombo.aspx

All of the laser components are available here:
https://buildyourcnc.com/LaserComponents.aspx

And the spindles and VFDs are available here:
https://buildyourcnc.com/SpindlesAndAccessories.aspx

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hello, I'm interested in GreenBull 5'x10' CNC machine kit with 40W laser head. Is it possible to receive an offer for this size cnc machine kit with all the mechanics, electronics and laser parts, but without all the wooden parts? We would like to build this kind of laser cutter machine with metal frame and parts. And is it possible also to get 3D drawing for machine? Waiting for your answer.

With our current models, that is a no. However our machines have the ability to be expanded length wise to the customer's choice. So you can design a share table if you add the required length of chain and rails and design the table accordingly to your specifications.

Click the link to add information to this solution:
The blackFoot 4'x8' CNC machine. Can Gantry be removed for festool track saw operation? A shared table situation. I am thinking that would be a no answer. But maybe a future design feature as run the gantry to far end and add a short opposite end section to allow a shared table set up.

We may be able to source those motors. Curious, the 6000 oz-in motor is pretty big. Do you mind explaining the application of the CNC machine and the structure that would require the large motor?

Additional Information:
The largest motors we can offer is 3900 oz-in without any mechanical help. 6000 oz-in can be resolved by mechanical means as an alternative.

Click the link to add information to this solution:
I am converting a 12x36 lathe over to CNC, I am interested in a 2 axis kit. I would love one stepper motor to be no smaller than 1200oz. , and another at 6000z. Is this something that you could offer? I have two other cnc machines but this is my first converstion on my own.

I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

Click the link to add information to this solution:
I HAVE NOT SEEN ANY REFERENCES TO ENCODER FEED-BACK CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?